MISFIRE/SPARK PLUG REPLACEMENT / MERCEDES
HTML-код
- Опубликовано: 1 окт 2024
- Mercedes-Benz 2006 c230 v6
+SPARK PLUG REPLACEMENT /regaping
+air filter replacement
+COIL PACK REPLACEMENT
🔵PLEASE LIKE & SUBSCRIBE 🔵COMMENT BELOW
🔵 / joshyodenn
🔵[SOCIAL MEDIA]
🔵 = / joshyoden
🔵= / joshyoden-158441003833...
🔵= / joshyoden
🔵= / joshyoden
🔵[DONATE]=www.paypal.me/...
🔵[SEND STUFF HERE]= PO BOX 336, MIDDLEBURY, IN 46540
🔵[Disclaimer] THANKS FOR WATCHING!!
Joshyoden cannot guarantee against improper use or unauthorized modifications of this information. Joshyoden assumes no liability for any property damage or injury incurred as a result of any of the information contained in this video or any information on this channel. Use this information at your own risk. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the responsibility of the user and not Joshyoden.
{I HOPE THIS VIDEO HELPED YOU}
Please comment with any questions!
![FendiDa Rappa - Clock Dat ft. Shamar Marco [Official Music Video]](http://i.ytimg.com/vi/3NBU8KHdxYY/mqdefault.jpg)
If you have a misfire, you might as well change all plugs and coils if youre gonna crack it open for one plug, and a check engine light.....and the screws are called Torx head screws.
Cylinder numbering is incorrect.
actually, that is correct for the C class of this generation
@@TheRebuilt1 - You are correct.
What is the firing order for 2010 E350? 4matic
I was told that the spark plugs go back and forth side to side so one on the right two on the left three on the right four on the left
DON'T use an Allen/hex key on Torx screws, you will damage the screw heads.
I found that the plug gap increases with use. Mercedes specs .031" and I measured twice that. Remove all the plugs, clean the threads and bend the ground electrode till you get .031". If you do this every 20000 miles or so, you will save the coils. Also, use electronic contact cleaner on the coil connector. I had no bad coils after doing this.
For anyone doing this, save yourself the hassle and just give yourself a full tuneup in this situation. Spark plugs are put in at the same time. If one goes the others are bound to go eventually. So don't go through the hassle twice! Do it right the first time!
Not true with my experience
@@merlincaren1 could of been changed prior to you doing the work, or u may also have had bad intake gasket, which would have caused your spark plug to fowl out or could have just changed everyone but that one you changed, they're constantly being used, and usually have around the same life expectancy unless uneven engine power is being distributed. Ur situation CAN happen, but now ur risking doubling if not 4-11x the labor by changing one by one out.
Yeah mines gone Ive just ordered 6 bosch plugs and 6 NGK's 456 and missfire and its started at 4 so Im just going to replace the whole lot incase they are like light bulbs
If you don’t know whether or not your coil is bad, use a voltmeter to check the ohms. A new coil should have a resistance of 1.3. There’s no need to guess.
Please my GLC 300 the cylinder 3 is misfiring and the car vibrates code P030385
Amazing video! Very helpful! My car is no longer misfiring! The only issues I have now is my temperature gauge is dancing up and down. Hopefully I can figure that out
You. Have you cylinders wrong #1 is passenger front of the motor not the rear
many videos, none speak of proper gap, mine 2006 c230 v6
Awesome video, I'm having the same issue, and coincidently ordered k&n filters
This sparkplug could have been dropped during installation. I've seen this over and over once you set the gap on your plugs then one slips and lands on the end of the plug it mashes the gap closed. Always recheck your gap if the plug is dropped.
Nice work,and helping.
thank you,,,my friend
My 6th one is misfiring should I change all 6 or just the one?
That really depends how old they are.
They recommend changing them every 50,000 miles.
Thank you
Then if your OBD says it’s fine why there’s still a check engine light?
You have to reset the code or drive for about 60miles for it to clear
Hi there sir. How r u. My car cranks but wont start when its hot. I keep getting code p0300 p0301 and p0302 p0303 and p0306 p0304 and p0101 and p0113
Hi great job. Do you have video on Rear SAM removal replacement for w251 mercedes or similar model.
I don't have a video for that, but it should be located inside the car behind the rear passenger side wheel well ,underneath everything, mounted to the shell of the car. Make sure to disconnect negative battery cable when taking this apart so you don't end up with fault codes.
images.app.goo.gl/iJxMfA2mVoi6T5LV7
How to solve this problems?
Do you have to torque the spark plugs?
hey bud there is a round disk for sparkplug gapping
Whats the spark gap for these plugs for this engine?
The spark plugs for this car come pre-gapped. They dont make a manual gap plug for these cars
.031 as in the owners manual. Most all modern plugs do come pre gapped, but the spec is still listed for a reason.
Mine has cylinder 1 and cylinder 3 spark plugs misfiring should I change just both or all 6?
I recommend changing all 6 unless they were recently changed
Yes always change all the plugs at once it's the best and they're not expensive