An Thread Method Using For Repairing to Broken Truck Axle Which is Very Amazing Technical Process..
HTML-код
- Опубликовано: 9 мар 2023
- An Thread Method Using For Repairing to Broken Truck Axle Which is Very Amazing Technical Process..
#brokentruckaxle
#usingthreadmethod
#pkprocess Авто/Мото
В 93 году по такому принципу я укоротил мост газ 51под двигатель т 25 с газоновской КПП. До первого рывка. В выигрыше только токарь.
привет
Nice job
"You picked a find time to leave me, Loose Wheel"
Отличный ремонт полуоси,
говорю как водитель с сорокалетним стажем!!!
Так делали(не все правда) настоящие специалисты - в СССР!!!
Теперь после сварки, термическая обработка - отжиг - закалка - отпуск!!!
привет
Pierde temple por la soldadura, se rompe como queso, la dureza no es igual, zona afectada termicamente
наверное это самая некачественная работа которую я видел! количество косяков просто зашкаливает за все разумные пределы!
❤❤❤ greet
Good work
Nice video shot, thanks for sharing, keep it up :)
Just because something is broken does not mean the need for it has gone away. You use your tools with great skill. Very fine job.
Mlh❤
You obviously never trained in a machine shop. And by the looks of it, neither did these guys. Agricultural is too much praise.
Poop
Now THIS is a quality repair with serious longevity.
I like your sarcasm.
The turner's work is very good. The end result will depend on the hardening and thermal tempering of this truck drive shaft, greetings 😀.
Thank you for the like 😀.
Well done . Botchers INC
Needs a bit of practice with the cutting torch.
Non so l inglese lo dico in italiano vedere lavorare in questo modo è veramente fantastico, con poco fate cose che sono impensabili, grazie ❤
Buen trabajo maestro.
Mua chiếc mới rẻ hơn công làm lại
Muito profissional parabéns pelo trabalho Brasil
Very professional congratulations on the work
Brazil
YOUR SYSTEM OF FIXING THE AXLE IS BRILLIANT AND UNIQUE KEEP UP THE GOOD JOB
Es un trabajo que se hace cundo no encuentras el eje original ,pero veo que con la soldadura dentro y afuera queda bien fuerte....
Somebody should learn how to use an oxy/acetylene cutting torch, the cutting shown at the start, that was a complete screw up
What about cutting away where the "hub centric" wheel is supposed to ride. Also, cutting away and/or not measuring the seal surface against the back of the flange.
@@ashleydog45 33
@ashleydog45
Pure genius with the lathe, the torch not quite so well done. Still exciting to watch though. Thank you.
Best way❤
Токарь от бога, и инструмент у него классный. Еще интересно куда они эту укороченную полуось применят
❤😂🎉😢😮😅
Зато резаком резать не умеют😂
привет
Very talented..
Man, These dudes get stuff done, Hats off to them for that. At least that vehicle will move again. How long? They have HUGE faith in that 3 jaw chuck. What is the T.I.R. on that?
Con pulidora y Disco de corte se corta mas rapido
Excellent and very creative work 👍👍
👍👍👍
عاشت يدك عملك متقن
С помощью токарного станка на иномарке проявлялась граната от Ваз 2108. Может кто-то вспомнит.
привет
Если бы на конус проточил и на горячую затянул, то может быть и ездило, а так вряд ли.каким боком резьба поможет?
Exselente trabajo.cuando no.ay.partes.nuebas.tienes.k aseralgo
Сварки мало!!! Всё порвёт!!
Don't lathes need water or fluid on the job
👌👌👌👌👌👌👌
Nossa muito bom seus vídeos falo de São Paulo Brasil
👍
So many things done wrong! Where do you start??
NEVER trust that axle on a public roadway!!!
No matter, customer will overload the truck again & the axle will snap right at the inside weld!
Hubiera quedado más fuerte si le hicieras un buje al platillo en la parte exterior con una cuña y unas décima de apriete y lo metías a precion y usaras soldadura en la parte de afuera solamente para que no parta Coelho calentamiento
Сварка через сломанное стеклышко одним глазом, не думаю что хорошо влияет на зрение и организм в целом.
Rutilo y sin precalentar. Con un par.
Это типа, кап ремонт, без гарантии 😄😄😄
Totalmente de acuerdo, un craso error
Will it hold ?
Belo trabalho. 🇧🇷
The perfect job, thank you
How long will this hold ? I’m assuming not very long.
Bravo
Hay
Bro how they do the thumb up at the end 😂😂😂
BRAVO !!!!
انتم من اي بلد
انتم فنانين وعباقرة
Все, новая, даже муха не сидела!
don't buy a new shaft?
clean the tip !
Perhaps the most important lesson is that if the result looks good, that means nothing. A lot of time is spent on making things look smooth and shiny. Too bad that time wasn’t spent on making it stronger. Or at the very least, paint in the windshield “max load 5 tons”. Or better yet “DANGER”
Супер
He should have used a grinder ist fast and clean
Nhìn chuyên nghiệp qua
Жесть, потом удивляемся почему колеса отваливаются.
Ты чимо
привет
С такими непроварами шов я бы не принял
Тебя ни кто не спрашивал чмо
привет
Welding current passing through lathe bearings is a NO NO
What about heat treatment ?
Most of welds machined away
JUNK !
Well done...
press fit weld is strongest
Muy bien
Jode to diya ye chalega?? Thareding ki jagah miling kiya kro. Ye bacho wale kam hai
Where does the outer axle bearing ride? shouldn't that area be mic'ed and cleaned up?
It's a floating axle, the bearings are usually located in the drum assembly for large trucks.
До первого груза а потом на чермет .
привет
Заварили плохо и без термо обработки это брак !!!
Serviço perdido não aguenta
привет
No habria sudo mejor hacer soldadura con dos puntas sin roscar o porque lo roscaron
A possibilidade de quebrar , sem a rosca é maior. A rosca reforça é diminui a chance de quebrar. Milton - Brasil
💀🤡😎🌝
Poor old lathe, how mistreated.
сварка плохая проточка для сварки маленькая
привет
Бедная страна. Талантливые люди.
Рф тоже нищая,😂
Bakwas log v phodo ban jaty hein😂
😂😂
こんなのすぐ壊れておしまいだよ。
ネジ切ったって、何の周り止めにもならないんだから、まだ圧入の方がマシ。結局は溶接でくっつけただけの強度しか無い。
スプライン切るなら分かるけど、ネジ切ったのは無意味。
No strong this ideas totly fail
👍👍
👍👍👍👍👍