Great video, very clear. Thanks. Can I suggest something: add a short demo of the end result at the beginning and end. Like: We are going to build this functionality... Your showing of the end-result was only a few seconds. A bit more time there would make it easier to understand what the goal (end-result) is.
Thanks a lot for the fantastic video!! May I ask such a basic project, what could possibly cost? (just a rough estimations - exclude wiring. Just all h/w parts)
Thanks for the comprehensive tutorial! What I don't understand though why do you need a led controller, 24v power supply and a dimming actuator? I thought if I'd get the MDT AKD-0424R.02 that this unit would provide the power and dimming capabilities for the led lights to dim, power on and switch on & off? Am I wrong in my assumption? Either way good video man :)
In this video i used a 1-10V Dimming Actuator and that is why i had to use a LED Controller. 1-10V Dimming Actuators are very common and you can use them to drive Led Strips without worrying about the load. MDT AKD-0424R.02 can drive directly 1 to 4 Led Strips (4A per Channel) without the need of external LED Controller.
Hello, Many thanks, those videos helped answer a lot of questions I had about KNX. As you have a broad knowledge of Weinzierl devices, I would have a question about the Multi I/O 570 : I would like to use it to read the state of regular switches in a house (As I would prefer them over push-buttons) and wonder if this unit can trigger a telegram whenever a regular switch has its state changed (regardless if it changes from off->on OR on->off). I would then simply toggle an output on each rising or falling-edge for example. From their documentation I feel like it is possible but I'm not 100% sure.Also would see any reason not to go for this setup ? Many thanks for your insights, have a lovely day !
Thank you for your comment! You can also check : How to program KNX Devices - KNX Programming Tutorial : ruclips.net/video/WxD8TScEAP4/видео.html KNX IP Baos 777 - Visualization and Voice Control with Alexa : ruclips.net/video/2It2pQsjwAM/видео.html More episodes will come in a while!
Thanks for doing this! I'm currently setting up a KNX system myself, and my KNX bus cable has 4 wires like yours but with an additional bare copper wire in there too, what would that be used for??
Thank you! You can find the list of all KNX Devices in the description section of this video. For every product at the beginning of this video there will be a tutorial, so stay tuned!
Hi very helpfull and easy for biginners to understand. I am interrested to know thé price of all parts in tout démonstration. Thanks and keep on tour vidéos.
Thanks! The KNX devices are : 1) K-Bus KNX Power Supply : www.video-star.com.cn/en/ProductsDetail.aspx?code=010107&id=27 2) MDT KNX Dimming Actuator : www.mdt.de/EN_LED_Controller.html 3) Vimar KNX Switch : www.vimar.com/en/int/catalog/product/index/code/20840 4) Weinzierl KNX Baos 777 : www.weinzierl.de/index.php/en/all-knx/knx-devices-en/knx-ip-baos-777-en You can find also useful links in the description section of this video!
@@PoseidwnTech thanks for great video, I love to start to integrate with our alarm system, camera, alarm, intercom, locks so can you suggest the list of KNX units.
A circuit breaker is an electrical switch designed to protect an electrical circuit (in our case the KNX Devices) from damage caused by excess current from an overload or short circuit. In this video i made an electrical demo cabinet so i tried to make it as close as possible to a real installation. Of course this was only for Demo, since in a real installation further protection is required.
Ωραίο βίντεο έβγαλες. Δουλεύω με αυτοματισμους εδώ στον Καναδά. Η τυποποίηση εδω δεν είναι KNX είναι BACNET. Έχουμε και MODBUS που και που. Έλεγα να μετακομίσω Ελλάδα να κάνω αυτοματισμους εκεί αφού είμαι και Έλληνας.
Try to restart the KNX device and try again. Are you sure that you are using the correct library for the device? Have you tried to make a full download instead of partial download?
hi .thanks for video .i have a question about smart draw .devices which you located in smart draw are pictures or are schematic of real device?how can i add them to the smart draw and wiring them same as you
I used images from the real products(Insert --> Picture) and then i connected them using the line tool of smartdraw. I will make a short video about this, so stay tuned!
@@PoseidwnTech Thank you have reply comment of me. I am learn on Room master in the lamp control, do not know any connection, you can only be only? tks.
Please someone help me , i didn’t get the all required components for KNX system , because of my English. 1- power supply 2- 3- 4- 5- What r all of them ??
I believe that it comes from the latin word "CONEXIO" which means Connection. So "CONEXIO" --> "KONEX" --> "KNX" When i will find the original source for the meaning i will write it in the comments!
Thank you all for your support!
KNX Tutorials Playlist : ruclips.net/p/PLNJVyvij10Ftuv3Ng7gcBgU-Ztco8T_SJ
Φίλε πραγματικά είσαι απίστευτος, σου βγάζω το καπέλο... Από σήμερα είμαι φανατικός σου οπαδός
Σε ευχαριστώ για τα καλά σου λόγια!
I`m not commenting so often on youtube videos, but yours deserves that. Very helpfull introduction to KNX.
Thank you very much for your comment. I really appreciate it!
Thank you for refreshing what i learned in school a couple years back :)
You are welcome! Thank you for your comment!
nice video, thank you for help me 6 years later
I am glad that my video helped you!
Smart Home . Smart Life
This is our motto❤️
Nice!
This is one of the best videos for KNX explains. Witting fro next episode. Thank you very much.
Thank you very much for your comment! The next episode will be available soon!
Great video, very clear. Thanks. Can I suggest something: add a short demo of the end result at the beginning and end. Like: We are going to build this functionality... Your showing of the end-result was only a few seconds. A bit more time there would make it easier to understand what the goal (end-result) is.
Thank you for your comment! I will try to do that to the next videos!
Maybe a stupid question… why do you need a second power supply for the LED stripe? You already have a power supply for your installation?
If you make reviews for all these products it will be amazing! I am waiting for more. Thank you!
I will make reviews for all of them, so stay tuned!
Thanks a lot for the fantastic video!! May I ask such a basic project, what could possibly cost? (just a rough estimations - exclude wiring. Just all h/w parts)
Μπράβο επαγγελματίας!
Σε ευχαριστώ για το σχόλιο!
Excelente explicação e didática ,,, parabéns pela iniciativa e ajuda aos profissionais .
Thank you!
Verry good explain...
Thanks
Thank you for your comment!
This channel is the best! Thanks a lot. Would you please make a video about Heating Actuators and thermostats?
Thank you for your comment! Of course there will be an episode about KNX Thermostats!
Very good,.. tutorial
Thank you!
Thanks for the comprehensive tutorial!
What I don't understand though why do you need a led controller, 24v power supply and a dimming actuator?
I thought if I'd get the MDT AKD-0424R.02 that this unit would provide the power and dimming capabilities for the led lights to dim, power on and switch on & off?
Am I wrong in my assumption?
Either way good video man :)
In this video i used a 1-10V Dimming Actuator and that is why i had to use a LED Controller. 1-10V Dimming Actuators are very common and you can use them to drive Led Strips without worrying about the load. MDT AKD-0424R.02 can drive directly 1 to 4 Led Strips (4A per Channel) without the need of external LED Controller.
Very useful video sir thank you.... Please share how to connect motion sensor with knx
Thank you for your comment! I will try to make a video for KNX presence detector.
Thank a lot ! very helpful .
You are welcome!
Hello, Many thanks, those videos helped answer a lot of questions I had about KNX.
As you have a broad knowledge of Weinzierl devices, I would have a question about the Multi I/O 570 :
I would like to use it to read the state of regular switches in a house (As I would prefer them over push-buttons) and wonder if this unit can trigger a telegram whenever a regular switch has its state changed (regardless if it changes from off->on OR on->off). I would then simply toggle an output on each rising or falling-edge for example. From their documentation I feel like it is possible but I'm not 100% sure.Also would see any reason not to go for this setup ? Many thanks for your insights, have a lovely day !
Great, more video tutorial is needed
Thank you for your comment!
You can also check :
How to program KNX Devices - KNX Programming Tutorial : ruclips.net/video/WxD8TScEAP4/видео.html
KNX IP Baos 777 - Visualization and Voice Control with Alexa : ruclips.net/video/2It2pQsjwAM/видео.html
More episodes will come in a while!
Thank you very much
You are welcome!
Thanks for doing this! I'm currently setting up a KNX system myself, and my KNX bus cable has 4 wires like yours but with an additional bare copper wire in there too, what would that be used for??
i guess thats just a ground wire
Which is the building with the pool at the beginning of the video ?. Good job, keep going.....
Thank you! This is a Hotel in Greece!
Very beautiful country, I would like to come for holidays.
Great video! Could you please give a shortlist items and where to purchase as well?
Thank you! You can find the list of all KNX Devices in the description section of this video. For every product at the beginning of this video there will be a tutorial, so stay tuned!
Cheers bud.
Good one..!
Thank you so much 😀
Great video Poseidwn,can you tell me what is the name of this simulation program?
Thank you! The visualization program i am using is Iridium Pro by Iridium Mobile.
www.iridiummobile.net/pro/
Hi very helpfull and easy for biginners to understand.
I am interrested to know thé price of all parts in tout démonstration.
Thanks and keep on tour vidéos.
Hi! Thank you for your comment. For prices please contact the manufacturers or your local distributors.
thanks for the helpfull vedio, can you tell me what kind of program or software have you used for drawing of the knx component?
You are welcome! For my drawings i used SmartDraw : www.smartdraw.com/
Great video!
Could you also provide a list of materials so that we can start practicing ?
Thanks! The KNX devices are :
1) K-Bus KNX Power Supply : www.video-star.com.cn/en/ProductsDetail.aspx?code=010107&id=27
2) MDT KNX Dimming Actuator : www.mdt.de/EN_LED_Controller.html
3) Vimar KNX Switch : www.vimar.com/en/int/catalog/product/index/code/20840
4) Weinzierl KNX Baos 777 : www.weinzierl.de/index.php/en/all-knx/knx-devices-en/knx-ip-baos-777-en
You can find also useful links in the description section of this video!
@@PoseidwnTech thanks for great video, I love to start to integrate with our alarm system, camera, alarm, intercom, locks so can you suggest the list of KNX units.
what is a circuit breaker and why do I need it? why wouldn't I just plug the power supply into the power outlet directly?
A circuit breaker is an electrical switch designed to protect an electrical circuit (in our case the KNX Devices) from damage caused by excess current from an overload or short circuit. In this video i made an electrical demo cabinet so i tried to make it as close as possible to a real installation. Of course this was only for Demo, since in a real installation further protection is required.
Ωραίο βίντεο έβγαλες. Δουλεύω με αυτοματισμους εδώ στον Καναδά. Η τυποποίηση εδω δεν είναι KNX είναι BACNET. Έχουμε και MODBUS που και που. Έλεγα να μετακομίσω Ελλάδα να κάνω αυτοματισμους εκεί αφού είμαι και Έλληνας.
Σε ευχαριστώ! Αν και δε γνωρίζω πως είναι τα πράγματα στον Καναδά για να συγκρίνω, πιστεύω ότι στην Ελλάδα θα υπάρχει αντικείμενο να ασχοληθείς.
hi,
how can send date and time over knx devices?
which device proper for achieve this?
thank you so much
S3 or S7 touch panel of GVS.
When downloading the program to the device, the download fails and it prompts that there is an error writing to the memory block. What is the reason?
Try to restart the KNX device and try again. Are you sure that you are using the correct library for the device? Have you tried to make a full download instead of partial download?
Very nice
Thank you!
hi .thanks for video .i have a question about smart draw .devices which you located in smart draw are pictures or are schematic of real device?how can i add them to the smart draw and wiring them same as you
I used images from the real products(Insert --> Picture) and then i connected them using the line tool of smartdraw. I will make a short video about this, so stay tuned!
AWESOME AWESOME AWESOME
Thank you!
Καλησπερα
Μπορεις να με συμβουλέψεις για μια μισοτελειωμένη εγκατάσταση στην περιοχή της ΒΑΡΗΣ αττικης;
Καλησπέρα, μπορείτε σας παρακαλώ να μας στείλετε email στο info@poseidwntech με τα στοιχεία σας προκειμένου να επικοινωνήσουμε μαζί σας;
Name of program please
Hi ! Can you use smartdraw software to draw intelligent knight lighting control knx using RM / S 2.1. tks very much
Hi! I am not sure that i understand. Do you need the connections of ABB Room Master?
@@PoseidwnTech
Thank you have reply comment of me.
I am learn on Room master in the lamp control, do not know any connection, you can only be only? tks.
Please someone help me , i didn’t get the all required components for KNX system , because of my English.
1- power supply
2-
3-
4-
5-
What r all of them ??
1) Power Supply
2) Sensors (Switches, Thermostats, Brightness Sensors, etc)
3) Actuators (Switching Actuators, Dimming Actuators, etc)
4) KNX Bus Cable
Poseidwn Tech so these are the all things i need to convert my home to smart.
Thank u so much for helping
Can i ask u please : how much approx each one cost.
将程序下载到设备时,下载失败,并提示写入内存块时出错。原因是什么?
Try to restart the KNX device and try again. Are you sure that you are using the correct library for the device?
god job
Thank you!
where can I find the Video about the KNX controller from Weinzierl?
You will find it in a few days... Now i am working on the Episode 2 that it will be about ETS and the next one will be a review of Weinzierl Baos 777!
You can find the episode regarding KNX IP Baos 777 to the following link : ruclips.net/video/2It2pQsjwAM/видео.html
where did you buy knx bus cable?
Hi! For KNX bus cables i am using local stores with electrical supplies in Greece.
i wanna ask for meaning KNX what full name.thank you
I believe that it comes from the latin word "CONEXIO" which means Connection.
So "CONEXIO" --> "KONEX" --> "KNX"
When i will find the original source for the meaning i will write it in the comments!
@@PoseidwnTech i will be thank you
Of anyone watching this wants a KNX installation job, near Faro, please message me !
nervous video
he dose not know that KNX is not SMART ;-) !
😃