Thanks Tino for another great video. I feel quite confident now to remove the main sail and set it up again. Your videos are great and very informative and you always manage to explain it so simple. Looking forward to more videos (y)
I’ve just stuck at the lower mast corner swivell… I was about to squese mt finger into sail gap to unleash, then I deicided to search in RUclips for if there’s a way 😂😂😂 I made may headsail furler lubricating also 5 months ago thanks to your videos…
as the sail halyard connection is in such a cramped space, a tip, use some "never seize" on the threads of the shackle, that way it's easy to remove the next time, but also perhaps a good idea to "wire in" the pin, on the hole in the shackle pin head, so it doesn't vibrate loose (and so you DON'T have to use Loctite on the thread, which will make it harder to remove).
Thanks again Tino. I have exactly the same setup. But my halyard swivel is stuck in the down position. Help! I dropped and removed the mainsail. Now the halyard swivel is stuck between the 2 inspection ports. I cannot raise it.
@16:49, you ALSO use the topping lift to support the boom weight while the sail is NOT set, for "rope" boom vangs, as with these 'loose' systems the boom WILL fall without topping lift tension. also this allows hydraulic vangs to be stored at low load/ pressure conditions enhancing life of rigging.
Good Morning. Useful video , I need to remove my mainsail tomorrow. How long is your continuous line, and what is the size of rope you use? What tension do you put on the haliyard? Cheers
I am thrilled to have discovered your video. Thanks for your efforts. Question: to reef before setting sail must you unfurl the main fully then reef in to shorten the sail. Or can unfurl the amount of sail I require? I hope you have the time to answer.
The furling system is made so you have two modes. In "free" you can furl the main in and out as desired with the endless rope. In "ratchet" it is only possible to furl the main in, the point with "ratchet" is the furl is locked in one direction so your main sail can't furl out in a storm. You don't have to furl the main sail all the way out to use "ratchet".
Hi Tino, Thank you for the video, I’m new to inmast furling and just wondered if you are at sea and want to take a reef do you also try and tighten the rod kicker to try and keep the sail straight at the leach. I have the same rod kicker and it does not support the mast when the topping lift is off, it drops onto the cockpit cover . That was very useful ,thank you again .
Think the gas damper inside your rodkicker is defective. I have a video how to change it, think a 1200N would be the best choice. Yes the rodkicker must be tight and the topping lift must be loose when reefing.
I wanted you to show how you control the spindle line and out haul simultaneously and on which winches during setting and unsettling the main. I have used the same never ending line and ratchet system you have, but in combination with what we call the German sheet system {double ended main sheet} and no cabin top winches. In that system the out haul is to port and never ending lines to the spindle are to starboard. Two people are needed to get it in and out. So I really don't like it.
Ok nice to know. I know "the german system" is on the new models of the Bavarias but I have never tried it. The old system has also got some critics over the years but for my use I think it's ok.
@@twiper The German system is great for accessing the mainsheet from the helm, especially with electric winches. But not if you're crew and and forward of the winch. Also not great for self tacking jib..... which has only one sheet that half the time must share the mainsheet winch (on starboard tack in the case of this particular jeanneau 410). That winch is also used by the never ending in boom line. So on this boat I spend a lot of time squeezed behind the helmsman, scrunched over that winch. So combination of never ending line furling and German mainsheet and self tacking..... Is the pits. IMHO
Hej . jeg har købt en LM 28 som har en selden mast og ved ikke de fjerneste om sådan en fin rulle mast . tror den skal strammes op inde i masten , er det noget du ved en masse om jeg har pillet masten af for vinteren og til foråret skulle jeg jo gerne ha den på igen og trimmet ind så sejlet ikke folder . så jeg kunne rigtig godt bruge nogle gode råd med venlig hilsen Henrik B Hadsund ps. ellers rigtige gode videoer du har lage op
Tino Nice video but you did not mention how you tensioned the main Halyard before reefing in the sail. I use one of the pulleys at the base of the mast and lead the halyard trough the sprayhood window and tension up the halyard using one of the winches on the cockpit roof. I found that `I could not get sufficient tension by just pulling the halyard through the mast clutch even when using my foot in a loop of the line. My system requires that you have to unreeve one of the lines at the base of the mast in order to provide the required pulley. In my case, I use the kicker line but it is a little tricky to pass the line back to the cockpit under the deck fairing. Hope this helps. Carry on with your useful Videos.
Thanks :) I did not tighten the main halyard crazy, it is also bad for the sail if it is to tight for a long period of time. If it wrinkles under sail it's too loose but for my use a good handtight halyard is enough.
TG- The only decent Selden maintenance on RUclips.
A GREAT video.
Wish SELDEN would produce an OFFICIAL video on the SAME procedure.
Great job! One of the most useful video for furling mainsail owners. Thank you for filming the process.
Great video Tino You explained clearly and showed us everything I need to know about the Seldon in mast furling system Thank You
Thanks Tino for another great video. I feel quite confident now to remove the main sail and set it up again. Your videos are great and very informative and you always manage to explain it so simple. Looking forward to more videos (y)
I’ve just stuck at the lower mast corner swivell… I was about to squese mt finger into sail gap to unleash, then I deicided to search in RUclips for if there’s a way 😂😂😂 I made may headsail furler lubricating also 5 months ago thanks to your videos…
Very good your explication about remove the mail sail furlex mast.... Gooood... I liked👍👍👍
Tino, That looks like Egaa! Thank you for the great explanation.😃
So glad I found this video. Most informative one yet! Thank you.
Thank you... I am considering buying a boat with the Seldon Furling Mast.
as the sail halyard connection is in such a cramped space, a tip, use some "never seize" on the threads of the shackle, that way it's easy to remove the next time, but also perhaps a good idea to "wire in" the pin, on the hole in the shackle pin head, so it doesn't vibrate loose (and so you DON'T have to use Loctite on the thread, which will make it harder to remove).
Nice video Tino, itäs pretty much the same as ours, except we have a load of battons in the sail to deal with as well. Nicely done
Very helpful videos Tino, simple and practical! Thank you.
one tip, to save your sanity, use a "captive pin" shackle, that way you can't lose it, and makes the removal easier.
Very useful, thanks! I am new to almost everything so if any of you have video of removing the genova i would be ever som greatful for that too!
Just a brilliant video. Thanks for posting
Thanks again Tino.
I have exactly the same setup.
But my halyard swivel is stuck in the down position. Help!
I dropped and removed the mainsail. Now the halyard swivel is stuck between the 2 inspection ports. I cannot raise it.
@16:49, you ALSO use the topping lift to support the boom weight while the sail is NOT set, for "rope" boom vangs, as with these 'loose' systems the boom WILL fall without topping lift tension. also this allows hydraulic vangs to be stored at low load/ pressure conditions enhancing life of rigging.
Good Morning. Useful video , I need to remove my mainsail tomorrow. How long is your continuous line, and what is the size of rope you use? What tension do you put on the haliyard? Cheers
nice video. good tip about using the ratchet mode while furling
Thank you for the tutorial, very helpful :)
good video. thanks for that. it seems it can be done on the way too in case there is some need for that.
I am thrilled to have discovered your video. Thanks for your efforts. Question: to reef before setting sail must you unfurl the main fully then reef in to shorten the sail. Or can unfurl the amount of sail I require? I hope you have the time to answer.
The furling system is made so you have two modes. In "free" you can furl the main in and out as desired with the endless rope. In "ratchet" it is only possible to furl the main in, the point with "ratchet" is the furl is locked in one direction so your main sail can't furl out in a storm. You don't have to furl the main sail all the way out to use "ratchet".
In this video I show how the "ratchet" system works under sail : ruclips.net/video/aix2qCT8QxE/видео.html
Very informarive, thanks Tino
Thanks for sharing.
Hi Tino, Thank you for the video, I’m new to inmast furling and just wondered if you are at sea and want to take a reef do you also try and tighten the rod kicker to try and keep the sail straight at the leach. I have the same rod kicker and it does not support the mast when the topping lift is off, it drops onto the cockpit cover . That was very useful ,thank you again .
Think the gas damper inside your rodkicker is defective. I have a video how to change it, think a 1200N would be the best choice. Yes the rodkicker must be tight and the topping lift must be loose when reefing.
I wanted you to show how you control the spindle line and out haul simultaneously and on which winches during setting and unsettling the main.
I have used the same never ending line and ratchet system you have, but in combination with what we call the German sheet system {double ended main sheet} and no cabin top winches.
In that system the out haul is to port and never ending lines to the spindle are to starboard.
Two people are needed to get it in and out.
So I really don't like it.
Ok nice to know. I know "the german system" is on the new models of the Bavarias but I have never tried it. The old system has also got some critics over the years but for my use I think it's ok.
@@twiper The German system is great for accessing the mainsheet from the helm, especially with electric winches.
But not if you're crew and and forward of the winch.
Also not great for self tacking jib..... which has only one sheet that half the time must share the mainsheet winch (on starboard tack in the case of this particular jeanneau 410). That winch is also used by the never ending in boom line.
So on this boat I spend a lot of time squeezed behind the helmsman, scrunched over that winch.
So combination of never ending line furling and German mainsheet and self tacking..... Is the pits. IMHO
THANKS!!!! 😀😀
Thank you
Looks like your boom vang is upside down. Thick part usually goes to the top so it doesnt fill with water.
This helps me alot, tnx :D
Hej . jeg har købt en LM 28 som har en selden mast og ved ikke de fjerneste om sådan en fin rulle mast . tror den skal strammes op inde i masten , er det noget du ved en masse om
jeg har pillet masten af for vinteren og til foråret skulle jeg jo gerne ha den på igen og trimmet ind så sejlet ikke folder . så jeg kunne rigtig godt bruge nogle gode råd
med venlig hilsen
Henrik B
Hadsund
ps. ellers rigtige gode videoer du har lage op
Tino
Nice video but you did not mention how you tensioned the main Halyard before reefing in the sail. I use one of the pulleys at the base of the mast and lead the halyard trough the sprayhood window and tension up the halyard using one of the winches on the cockpit roof. I found that `I could not get sufficient tension by just pulling the halyard through the mast clutch even when using my foot in a loop of the line. My system requires that you have to unreeve one of the lines at the base of the mast in order to provide the required pulley. In my case, I use the kicker line but it is a little tricky to pass the line back to the cockpit under the deck fairing. Hope this helps. Carry on with your useful Videos.
Thanks :) I did not tighten the main halyard crazy, it is also bad for the sail if it is to tight for a long period of time. If it wrinkles under sail it's too loose but for my use a good handtight halyard is enough.
what was that polish you used?
how do you solve when it jams during reefing in strong winds?
I have not yet tried where it jams, think it jams more often when you have the version with sail battens.
@@twiper I have heard it jams if you reef down without enough tension, but same it might happen with regular mainsail.
I wish this guy knew the names of the parts he was showing.
Great job self editing your terminology. LOL Thanks of the video. You need a head mount or a videographer.
O
Learn the boat and sail part names.