PPF Pro Tips - Gel Vs. Slip Solution
HTML-код
- Опубликовано: 8 дек 2022
- In this video, Eric goes over what the differences are between using PPF Installation Gel and the traditional soap/water Slip Solution.
If you have any questions about installing PPF on your vehicle or any questions, comments or concerns, feel free to email Eric at eric@driveprotected.shop
Follow Eric on Instagram: @eric_sawatzky
Follow us on Twitter: @Drive_Protected
Follow us on Instagram: @driveprotected.shop
Follow us on Facebook: @ Drive Protected Shop
Find your pre-cut patterns here: driveprotected.shop Авто/Мото
Great videos. Thank you. What is the hardness for ceramic coating?
Thanks ❤
Cool!
Do you have video link where you mix the tack and slip??
I enjoyed the video. Very helpful. Where do I find the squeegees and glove to wrap the edges?
Check amazon!
Great vid 👍 what can I use at Home Depot for your “scraper” would a similar paddy knife work? I have a blk rubber thingy that came with a ppf kit not sure I like it much… thanks :)
Do NOT use anything from Home Depot for your install. Use the item that came with your PPF kit.
Great video which film are you using now? And how does it compare to xpel
Thanks! Using our Defense+ PPF. I love it.
Great video. What ratio do you mix the soap (j&j) and water?
This has been discussed many times on this channel.
Could you please measure "two pumps" of J&J for us. Your slip works really well for how you use it. I want IN because what I've used has still been pretty tacky. ...and if you are going to give us an actual measurement, has there been any refinements on this older video?
Going into exact measurements has not been productive I've found. A simple rule of thumb would be, if the slip is feeling tacky, add more soap until it stops being tacky. If the slip has way too much slip feel to it, just dial back the amount of soap you're using. 2 pumps is a general rule of thumb and works very good for us in our cold Canadian climate. However, if you live in a hot and humid climate, 2 pumps more than likely won't be enough soap. Hope this helps and clears stuff up.
@@DriveProtected Understood. Since I'm doing this on my own vehicles, I only bought myself an itty-bitty travel bottle. No pumps :(
Id recommend just playing around with it to find the perfect balance.
Thanks! Your content is so helpful!
Thank you so much!!!!
hello friend))) what can be used instead of Johnson baby, we don’t have it in Russia now (((what other formulations are suitable? what kind of baby shampoo is possible? and why only Johnson baby is used?
I would see if you can find dawn dish detergent. It works, just not as good as baby shampoo.
Попробуй Amwey, с белой крышкой, там почитай по щелочи, что бы минимум был) 1.5 инсулинового шприца на 1.5 л балона за глаза будет, а там как по кайфу)
Great video!! what is your tack solution? i guess i missed that part.
Tack solution is just hot water.
Hi. really helpful video for me to diy. Thank you.
Just have one question. Is it okay to use car shampoo for slip solution? Which one do you recommend between car shampoo and J&J baby shampoo?
Baby shampoo for slip solution. Do not use regular car shampoo.
@@DriveProtected Okay. Thanks for the advice :)
What is the process after ppf is on squeegeed and all the water is off?Do you wipe area with a towel or just let ppf area dry?
Always wipe it dry
Hi, what do you think about foam.
I did my first hood and roof with foam
and it turned out in a disaster. Water pockets and the edges are not tacking.
Greetings from Germany
Ralph
What kind of foam?
this gel same hight tak solution..same or different???
Different
Which software are you using for templates on your ppf kits?
We have used many kinds.
@Drive Protected so what are you using now then?
Very vague answer I would like to know also
how much soap in a 32oz bottle with distilled water?
Two pumps
Hi there
I really can't find you link under this video about J&J mixture... 🥺
Here you go: ruclips.net/video/RNWrxZGxL0M/видео.html
do you thing installing with gel will help push some potential small particles of dust trapped under ppf?
No. In my opinion it makes it harder to get them out.
@@DriveProtected thank you
I like gel in deep channels but mainly use j&j.
Agreed. Gel is really good in valleys!
Hi you said in this video you would put a link to how to make your slip solution I don't see that link can you send me the link please thanks!
PPF Pro Tips - How To Mix PPF Solutions
ruclips.net/video/DmcxmvRNUjs/видео.html
@DriveProtected hi there I subscribe to the channel and I just commented on your fender preping video with a few questions so I just wanted to ask you those questions when u get a chance to reply on the comments on that video just wanted to lyk thanks again...trying to get clarity and get to preping appreciate it.
@anthonyboria5738 that’s a lot of questions to ask in one comment.
How hot is the water you are using?
As hot as I can get out of the tap.
Whats in your tack solution
Hot water.
@@DriveProtected thanks brotha
@@DriveProtected no alcohol just hot water?
@anthonyboria5738 correct.
@DriveProtected thanks Eric hey I just sent you another message I'm trying.g to find your video on making slip solution I didn't see the link in one of the videos I was watching! BTW your videos are awesome dude best on RUclips I'm started a project with a gr86 can you send me a link I tried going all of your videos but couldn't find it lmk or if you could just lmk the ratio by message either or would be great...one this I wish I could find is in basic measurements like one half gallon to onces of baby shampoo hate the ml..ratios to be honest and liters stuff, throwing me off kinda of but yeah pls lmk that's eric!!