If your plane still show strong oscillations on the pitch axis try lowering the D term back to the original value of 0.04 or even lower. Autotune sometimes give nonconservative values of Pitch-D, which causes the oscillations that you show. On my wings (z84 and S800) I use 0.02 with good results. Awesome series of videos, congrats!
Awesome series, I decided to purchase all the hardware and AR Mini Wing to give it a go. I only had one issue and that was inability to connect to Mission Planner via the radio telemetry module, I would get the following error "no heartbeat packets received". - Connecting to Mission Planner with an USB was no problem. - The board in use in the Omnibus F4 Pro (v3) with the Omnibus 4.0.6 31-08-2019 selected and arduplane_with_bl.hex firmware flashed. - The radio telemetry module load settings checkout which indicates they are communicating - I triple checked the comm ports and baud rate setting, After doing some digging around, it turns out some telemetry module Tx and Rx pins are not marked correctly, so I switched my configuration and everything now works as advertised. Appreciate all the valuable content keep posting!
@5;30 was exactly the thing i have been dealing with I started to manually adjust to fix it but i think I have something else going on. Probable something basic I have overlooked, because the software was not able to correct it. Love this series Thanks again.
I have this little beauty and nothing but problems on launch specifically pitch oscillations at pre cruise speeds. No dought the ARDU boys have this figured out.. All I can say is goodbye INAV although thank you so much for INAVS contribution
When performing AUTOTUNE, do you take off in FBWA mode, then switch to AUTOTUNE mode, perform pitch and roll operations 20 times or more, and land in AUTOTUNE mode as it is? Or do you want to switch to FBWA before landing?
What are those little clips you use to keep the canopy on? Those would be great to keep the cover on mine from breaking the foam tabs that hold the front on during hard landings
Hi, Great info buddy but to go of topic I wanted to ask about the Paramotor. I have been watching them video you did but you have not done a flight test yet ( How come ) I have been told it's a pig to fly and I wanted to know your thoughts before I picked one up.
It's not too tricky but there is a few tips to get it flying with the minimum of hassle. I'm waiting to a nice enough day where my video buddy can film me from the 3rd person as you need to 'see' how to do the launch and how to test the brake line lengths before your first flight..
Hi,I have I am using GPS in APM board,I have APM 2.8.i have ublox neo8m .the gps work in rover firmware,I get GPS lock ,GPS work well rover firmware,but it doesn't work in arducopter 3.2.1. So if some could help ?
Sounds like a bug in the Arducopter code if it's working in the other types of Ardupilot code. APM is very old now and the retirement of the support happened then fixes are not happening (ruclips.net/video/Vbz3vN3JH6Y/видео.html)
If your plane still show strong oscillations on the pitch axis try lowering the D term back to the original value of 0.04 or even lower. Autotune sometimes give nonconservative values of Pitch-D, which causes the oscillations that you show. On my wings (z84 and S800) I use 0.02 with good results. Awesome series of videos, congrats!
It should be clearly stated that D gain of 0.02 should be a mandatory starting point for small agile planes. The defaults D gains are really bad.
Awesome series, I decided to purchase all the hardware and AR Mini Wing to give it a go.
I only had one issue and that was inability to connect to Mission Planner via the radio telemetry module, I would get the following error "no heartbeat packets received".
- Connecting to Mission Planner with an USB was no problem.
- The board in use in the Omnibus F4 Pro (v3) with the Omnibus 4.0.6 31-08-2019 selected and arduplane_with_bl.hex firmware flashed.
- The radio telemetry module load settings checkout which indicates they are communicating
- I triple checked the comm ports and baud rate setting,
After doing some digging around, it turns out some telemetry module Tx and Rx pins are not marked correctly, so I switched my configuration and everything now works as advertised.
Appreciate all the valuable content keep posting!
Post your settings for PTCH2SRV_P, PTCH2SRV_I, PTCH2SRV_D. You must have experienced oscillations with stock Arduplane settings.
Really fantastic what Arduplane can do, Lee! And it's not something new, which is even more impressive!
Thanks a lot for the series! 😃
@5;30 was exactly the thing i have been dealing with I started to manually adjust to fix it but i think I have something else going on. Probable something basic I have overlooked, because the software was not able to correct it.
Love this series Thanks again.
I’m excited to see AutoLaunch come as a dedicated flight mode. It’s one of the things that keeps iNav on top of Ardu for me.
It's simple to setup as it is now...
I have this little beauty and nothing but problems on launch specifically pitch oscillations at pre cruise speeds. No dought the ARDU boys have this figured out.. All I can say is goodbye INAV although thank you so much for INAVS contribution
Half your P gain if its a small wing... Happy flying!
Fantastic video as always, quick one here, Please can you share GPS link the one you are using
It's a generic M8N unit.. Nothing special.. Happy flying
When performing AUTOTUNE, do you take off in FBWA mode, then switch to AUTOTUNE mode, perform pitch and roll operations 20 times or more, and land in AUTOTUNE mode as it is? Or do you want to switch to FBWA before landing?
The best place to check any confusion is in the Ardupilot wiki. Things can change over time. Best of luck!
Can the Mission Planner hidden menus, such as found by pressing "Ctrl f " be used with such a FC?
What are those little clips you use to keep the canopy on?
Those would be great to keep the cover on mine from breaking the foam tabs that hold the front on during hard landings
I designed them. They are available to download for free from my Thingiverse page..
@@Painless360 oh, cool!
Thank you!
What if we try to fly plane with automode without making autotune,is this big problem ? (We dont have a pilot for autotune)
I wouldn't... Best of luck
Hi, Great info buddy but to go of topic I wanted to ask about the Paramotor. I have been watching them video you did but you have not done a flight test yet ( How come ) I have been told it's a pig to fly and I wanted to know your thoughts before I picked one up.
It's not too tricky but there is a few tips to get it flying with the minimum of hassle. I'm waiting to a nice enough day where my video buddy can film me from the 3rd person as you need to 'see' how to do the launch and how to test the brake line lengths before your first flight..
Hi,I have I am using GPS in APM board,I have APM 2.8.i have ublox neo8m .the gps work in rover firmware,I get GPS lock ,GPS work well rover firmware,but it doesn't work in arducopter 3.2.1.
So if some could help ?
Sounds like a bug in the Arducopter code if it's working in the other types of Ardupilot code. APM is very old now and the retirement of the support happened then fixes are not happening (ruclips.net/video/Vbz3vN3JH6Y/видео.html)
Should i try to use different GPS brand?,or I should use naze32 board?.or thier is any GPS fix for apm ?
Takeoff mode, coming soon!
Is there a way to get RSSI on the OSD?
Yep, check out the wiki.. Happy flying!
Amazing,