Although i disagree wiith you oneaning i means go to church i do agree with the message. We have to remember in churches we are hearing the interpretation of the bible from the pastor. We need more importantly to interpret it ourselves and compare to others.
”For whosoever shall call upon the name of the Lord shall be saved. How then shall they call on him in whom they have not believed? and how shall they believe in him of whom they have not heard? and how shall they hear without a preacher? And how shall they preach, except they be sent? as it is written, How beautiful are the feet of them that preach the gospel of peace, and bring glad tidings of good things! But they have not all obeyed the gospel. For Esaias saith, Lord, who hath believed our report? So then faith cometh by hearing, and hearing by the word of God. But I say, Have they not heard? Yes verily, Their sound went into all the earth, And their words unto the ends of the world.“ Romans 10:13-18 KJV bible.com/bible/1/rom.10.13-18.KJV
@@hattcreekfarm yes but a preacher is anyone spreading the word of Christ not just churches. John the Baptist wasn't a church nor was he a preacher of the church but he was a preacher. Preaching and baptizing without the arrival of the churches.
”not forsaking the assembling of ourselves together, as the manner of some is; but exhorting one another: and so much the more, as ye see the day approaching.“ Hebrews 10:25 KJV bible.com/bible/1/heb.10.25.KJV
Try adding the water to merely bring the cells to an equal level. Then dissolve the salt into your water bottle. THEN put it in your battery. I have never done this, but I heard that you can do it with a small amount of baking soda. Although baking soda is also used to neutralize battery acid. So I assume you would use only enough to trigger a chemical reaction.
Doin it incorrectly ! First drain battery upside down overbite put a box of baking soda in a gallon of di h2o soak in over nite shake it into a suspended solution fill up my batt let sit over night then drain bakin soda water out / take a pot heat up a gallon of di water 270 then dump in a package of Rodin salt stir into solution must desolve! Then let sit cool off then transfer liquid back into jug water add water to batt let sit over night too off in morning charge at 20 amps over night 13.5 surface charge! Dissipates in 1/2hr-12.66%then cover instal rite up vehicular and drive one hr that is a refurbished battery a Thomas Edison crude method if storage! Takes three days to do it correctly no telling how kind it will last don’t drain all the way down use it and keep a charge on it@2%
Thanks for the input, I’m just doing it the way someone showed me, I’ve done 3 batteries this way & 2 outta the 3 are still cranking, the one in the video was a bad battery, 2 of the cells had collapsed together, I will try this method!!
Lead acid batteries are properly and correctly filled when the electrolyte (the water/ acid mix) is approximately 1/8th of an inch above the tops of the plates, any higher causes voltage bleed out and liquid expansion out of the fill holes as in this case when it expands due to normal plate heating and over time only being (over)refilled with distilled water alone meaning its acid percentage drops, many a battery has been rendered useless by over filling thus causing boil off of the electrolyte most battery failures and diminishing charge retention are a result of the plate faces phosphating up over time lowering their abilities to tranfer ions to each other through the electrolite, and sluffed off lead oxide dropping off the plates and congealing on the floor of the battery where they sludge up and basically it continually shorts itself out meaning even a high amperage charge wont budge it. When a battery heats up under charging load it evaporates off the water....it loses barely any sulphuric acid - that mostly stays put...the bit that does however get out is what causes all that green and white shmoo on the battery connections ...that bubbling is actually highly explosive hydrogen gas which is being liberated from the H part of H2O(water) during the charging phase not as a result of epsom salts being added and was the reason you were coughing with stinging eyes, for the good of your continued health NEVER be tempted to use any kind of naked flame anywhere around where you can smell that gas ! but if the cells do over heat significantly due to massively high charge currents the plates can warp badly and buckle against each other causing a dead short the length of the battery and then it really IS game over for that particular battery the scam today is non servicable no fill batteries.........that way you cant service them and HAVE to junk them and buy another which pleases the manufacturers no end . by the way the charging process DOESNT "create" sulphuric acid THAT acid is pre installed diluted into distilled water at the correct percentage on first fill to act as its catilyser...hence why it is called ...a lead/ ACID battery. when fully charged it SHOULD read 13.5/13.6 volts, but the only way to really know if it is any good is with a deep draw discharge amperage test. its the amperage that does all the hard work not the voltage.....which is why they display the output in amps on the case. in future try to obtain a correct ratio acid/water mix first then lay the battery on its side and try to flush out all the shmoo on the case floor through all openings with a hose pipe for quite some time before drying and refilling it (one eigth above the plates remember) then charging it on a lower output.....try it and see.
That’s some very good information!! I only tried this because someone told me they tried it & it worked so there you go!! I’ve done 3 batteries so far & 2 out of the 3 are still cranking my mowers, I do have a so called maintenance free non serviceable battery that the same person told me what you just said about the manufacturer & why they say NON SERVICEABLE!! I’m gonna do a video on it when I get the chance!! Again thanks for the added information!!
@@hattcreekfarm My absolute pleasure my friend, as an automotive engineer for nearly fifty years it was just a part of my job, I wasnt calling you in any way shape or form, its just that chinese whispers and uneducated speculation seem to get real traction - I know a guy who knows a guy who's grandpa swears by, kind of thing, epsom salts are merely a kind of soda and may be beneficial in cleaning some of the crap off the plates - how much ??? I would be lying if I gave an amount. but I can say at least they dont cause any harm that I'm aware of, as I said try hosing out the inside of the battery (wearing sufficient protection obviously - sulphuric acid doesnt like people !) and try to come by some ready mixed battery fill - the acid content should be about three to five percent overall if memory serves me correctly, then charge it slowly on no more than a trickle charge, by the way I subscribed lol
@@usernamesreprise4068 I want to charge my Ebike batteries (6 - 72v 20ah) I watched a fews video's at first that used epsum salt & distilled water, most were to flush out and clean the batteries. Then I found a mechanic's video that demo's adding just distilled water nothing else however his technique is a bit different. He uses high cranking amps (200A) for 15 min. & then rest's the battery for 1 hour. He repeats this process 5x - 15min On - 1hr Off .. I don't have a charger that outputs 200A and I doubt many do, so I'm going to add just the distilled water, since there's a little acid left in the batteries, 1/8" above the plates' then use a trickle charger to charge them over night or 16hrs to 24hrs and see how that works. These deep cycle lead acid batteries are the same used on electric Forklift's and that's all we ever did was add the distilled water at the end of the shift and let it charge over night for the morning shift. THere is a pH tester you can use, I believe it was 4% but when they're being constantly filled it doesn't really matter testing them if the machine is running prop[erly.
i have seen folks do this in the past. and it takes a charge shows 12 volts. but when a load is put on it ,it dies so i will check to see if you are lucky and have a good battery
It does pretty good, it holds about 12.4 volts & cranks every time, I have done one other battery that didn’t do well but it’s because 2 cells were collapsed but have done 3 so far & 2 out of the 3 did good!!
Many years ago learned ago I found out how explosive car batteries can be, I had a freshly charged battery at my feet I was cutting steel with an abrasive cutter I had had a face shield on, I heard a loud pop finished cutting I found the top of the battery blown off, I had no injuries I lucked out.
i noticed no action in the cell at the positive terminal end, in my experience with batteries (20 yrs. ) that cell is bad check with a hydrometer, after the battery cools down
Yessir I don’t edit nothing out lol!!! There are those that have had negative things to say like I was boring or doing it wrong but if it gets good results then it’s not wrong!! However this battery in the video was in fact a bad battery, I have done 3 so far like this & the other 2 are doing great cranking!!!
I would have dissolved the Epsom salt into the water in the water bottle first, then added the solution to the battery with a small funnel. I'm not a chemist, but believe that by adding the Epsom salt, you're basically adding more sulfate ions to the liquid in the battery from the Epsom Salt (the SO4 in MgSO4). The original Sulfuric Acid in the battery also has the sulfate ions (the SO4 in H2SO4). I have a few dead batteries in my shop that I will try this on. Thanks for the video!
The recipe called for 1tsp of Epson salt per hole so I did it like that, as for the funnel I only had a big one thus the reason I used the spoon, funnel was bigger than the holes so more mess
It is new to me!! And it works, I have 2 batteries that it has worked on, the one in the video didn’t work cause it had 2 cells collapsed together so I melted the lead down into fishing weights
@@hattcreekfarm shoulda recorded one of the successful ones lol idk why u said it worked at the end while its on the charger without load testing it or anything. sorry about the comments maybe turn them off...pray for them,
I usually fill each hole with 1 table spoon of Epson salt then put it on charge, watch for the ones that don’t start to bubble then add another spoon full until it bubbles, when you see bubble activity I let it charge overnight, then check it asap that mawnin, no this battery had a collapsed cell I’m assuming because the charger read BAD BATTERY when I went to check it
@@au_gmentedreality it really works if the cells haven’t collapsed, some folks on here don’t know what it means to keep comment’s respectable & they will be removed, I don’t allow them on my channel!!
I study to show thyself approved. I went behind the Vail, and baptized myself. I am in the many membered body of Christ. I don't go to church the Bible spelled them out. He had 7 churches, 5 he snuffed out because they are nothing other than the sinaguages of Satan. He had 2 he liked and those were Smerna and Philidelphia they entertained and became 1. Hope you don't think you flying away. Put the gospel armor on and in place. Serve the purpose we are here for. 1st taken is by deception from Satan claiming to be God. Yes we are living in the last days of the 6 year creation. Warning it's happening as you read this Truth.
This was cool. Never tried the epsom salts trick so I might just have to do that next time. Here in the Texas heat I've had to top off some batteries with acid from the auto parts store in years past but that stuff is nasty. I've also tried the battery repair setting on the charger but thats a hit or miss depending on the type of battery. Anyways, God bless you brother.
The problem is that this trick doesn't always work? often on worn batteries this don't work! People think it works because they don't have a good battery tedters and don't know the condition of the battery. The car battery is also not designed to run on this white
All I know is, I tried it on my small engine batteries & 2 outta the 3 I did this to worked great & are still working!!! Haven’t done it on car batteries!!!
Apparently there are some folks who can’t read!!! I said keep your comments respectful or they will be removed!!! Listen to the video folks, I didn’t say that distilled & purified water were the same, I said that the big jug & what was in the bottle were the same, because I poured distilled into the small bottle because it was easier to pour from!! Some comments have been removed like I said they would be!!
Yes I didn’t know that it was collapsed at the time but after it kept heating up on that side I googled I & it said collapsed cell!! They say that some batteries during shipping if they get banged around or dropped this is what the most causes them to collapse!!
If your derp cycle battery holds a charge good there’s no reason to do this, only reason I did this was it wouldn’t hold a charge but I found out it had a cell collapsed
Very well said friend. I really thank you for your reading on going back to church to get recharged in our mind and spirit. We all need to get closer to God. ✝️
Yes, that is the number 1 priority!!! Thanks for watching, please like & Subscribe, it helps me to keep videos like this on here to keep Gods word flowing!!
@@hattcreekfarm I'm about a week into trying to restore a 12v deep cycle battery. 1st day was reading 1.8 volts and had a few bubbles in one cell. Now i can get it up to 9volts and there are 3 cells bubbling alot and the other 3 are just now starting to bubble a little bit. The metal inside the three cells that are boiling alot looks brand new and clean. The metal inside the other three cells still looks corroded. How long does it usually take to desulfate every cell? As long as the voltage slowly climbs higher, I assume that it is still progressing and desulfating.
I saw someone put something on RUclips about desulfurization using baking soda but you pour all the acid/water whatever you want to call it out into a container or bowl big enough to hold it all then they poured in a mixture of water & baking soda sloshed it around in the battery (with the caps back on of course) then let it set for some time (don’t remember how long) poured the mixture out then flushed the battery out with the water hose & refilled the battery with poured out contents & charged it!! You can go to google type in how to desulfurization a battery or bring a old battery back to life using baking soda & see where that takes you!!
What about the results ? What was the final voltage after doing the chemical additive and charging ? Were you able to place it back in the mower and show that it cranks like a charged battery?
This battery as I’ve commented in several replies, had a collapsed cell which resulted in it not holding a charge, but if you’ll read in these replies I stated that 2 others did great & are still cranking mowers!! Thanks for watching!! Please Subscribe!!
@@hattcreekfarm Before changing the polarity, the battery must of course be completely discharged and the voltage must be 0 volts. Then there is no risk of the battery overheating or exploding.
Ok thanks for the info may try this!! The battery in the video showed charging while I was doing the video but after the 24hr charge cycle my charger showed bad battery on the screen so I assumed it had collapsed cell so I’m just melting it down for the lead
I’m sure it would but not sure, just going by what I’ve seen others do with what they had that I’ve seen work!! You can google it to find out, I don’t have all the answers, just following someone else’s advice!!!
Grand pa taught me this epsom salt trick. I wish i could find a way to do this with sealed batteries, and agm. Thanks most of all for the bible verses. God bless sir.
You can prize the top off of maintenance free batteries with a screw driver or small pry bar what I’ve been told, just wear safety glasses & gloves & have a tube of silicone to reseal the top!! Might try this later & docs video
Although i disagree wiith you oneaning i means go to church i do agree with the message. We have to remember in churches we are hearing the interpretation of the bible from the pastor. We need more importantly to interpret it ourselves and compare to others.
”For whosoever shall call upon the name of the Lord shall be saved. How then shall they call on him in whom they have not believed? and how shall they believe in him of whom they have not heard? and how shall they hear without a preacher? And how shall they preach, except they be sent? as it is written, How beautiful are the feet of them that preach the gospel of peace, and bring glad tidings of good things! But they have not all obeyed the gospel. For Esaias saith, Lord, who hath believed our report? So then faith cometh by hearing, and hearing by the word of God. But I say, Have they not heard? Yes verily, Their sound went into all the earth, And their words unto the ends of the world.“
Romans 10:13-18 KJV
bible.com/bible/1/rom.10.13-18.KJV
@@hattcreekfarm yes but a preacher is anyone spreading the word of Christ not just churches. John the Baptist wasn't a church nor was he a preacher of the church but he was a preacher. Preaching and baptizing without the arrival of the churches.
”not forsaking the assembling of ourselves together, as the manner of some is; but exhorting one another: and so much the more, as ye see the day approaching.“
Hebrews 10:25 KJV
bible.com/bible/1/heb.10.25.KJV
Try adding the water to merely bring the cells to an equal level. Then dissolve the salt into your water bottle. THEN put it in your battery. I have never done this, but I heard that you can do it with a small amount of baking soda. Although baking soda is also used to neutralize battery acid. So I assume you would use only enough to trigger a chemical reaction.
Thanks for the advice!! And thanks for watching!! Please like & subscribe!!
Doin it incorrectly ! First drain battery upside down overbite put a box of baking soda in a gallon of di h2o soak in over nite shake it into a suspended solution fill up my batt let sit over night then drain bakin soda water out / take a pot heat up a gallon of di water 270 then dump in a package of Rodin salt stir into solution must desolve! Then let sit cool off then transfer liquid back into jug water add water to batt let sit over night too off in morning charge at 20 amps over night 13.5 surface charge! Dissipates in 1/2hr-12.66%then cover instal rite up vehicular and drive one hr that is a refurbished battery a Thomas Edison crude method if storage! Takes three days to do it correctly no telling how kind it will last don’t drain all the way down use it and keep a charge on it@2%
Thanks for the input, I’m just doing it the way someone showed me, I’ve done 3 batteries this way & 2 outta the 3 are still cranking, the one in the video was a bad battery, 2 of the cells had collapsed together, I will try this method!!
Lead acid batteries are properly and correctly filled when the electrolyte (the water/ acid mix) is approximately 1/8th of an inch above the tops of the plates,
any higher causes voltage bleed out and liquid expansion out of the fill holes as in this case when it expands due to normal plate heating and over time only being (over)refilled with distilled water alone meaning its acid percentage drops, many a battery has been rendered useless by over filling thus causing boil off of the electrolyte
most battery failures and diminishing charge retention are a result of the plate faces phosphating up over time lowering their abilities to tranfer ions to each other through the electrolite, and sluffed off lead oxide dropping off the plates and congealing on the floor of the battery where they sludge up and basically it continually shorts itself out meaning even a high amperage charge wont budge it.
When a battery heats up under charging load it evaporates off the water....it loses barely any sulphuric acid - that mostly stays put...the bit that does however get out is what causes all that green and white shmoo on the battery connections
...that bubbling is actually highly explosive hydrogen gas which is being liberated from the H part of H2O(water) during the charging phase not as a result of epsom salts being added and was the reason you were coughing with stinging eyes,
for the good of your continued health NEVER be tempted to use any kind of naked flame anywhere around where you can smell that gas !
but if the cells do over heat significantly due to massively high charge currents the plates can warp badly and buckle against each other causing a dead short the length of the battery and then it really IS game over for that particular battery
the scam today is non servicable no fill batteries.........that way you cant service them and HAVE to junk them and buy another which pleases the manufacturers no end
. by the way the charging process DOESNT "create" sulphuric acid THAT acid is pre installed diluted into distilled water at the correct percentage on first fill to act as its catilyser...hence why it is called ...a lead/ ACID battery. when fully charged it SHOULD read 13.5/13.6 volts, but the only way to really know if it is any good is with a deep draw discharge amperage test.
its the amperage that does all the hard work not the voltage.....which is why they display the output in amps on the case.
in future try to obtain a correct ratio acid/water mix first then lay the battery on its side and try to flush out all the shmoo on the case floor through all openings with a hose pipe for quite some time before drying and refilling it (one eigth above the plates remember) then charging it on a lower output.....try it and see.
That’s some very good information!! I only tried this because someone told me they tried it & it worked so there you go!! I’ve done 3 batteries so far & 2 out of the 3 are still cranking my mowers, I do have a so called maintenance free non serviceable battery that the same person told me what you just said about the manufacturer & why they say NON SERVICEABLE!! I’m gonna do a video on it when I get the chance!! Again thanks for the added information!!
@@hattcreekfarm My absolute pleasure my friend, as an automotive engineer for nearly fifty years it was just a part of my job, I wasnt calling you in any way shape or form, its just that chinese whispers and uneducated speculation seem to get real traction - I know a guy who knows a guy who's grandpa swears by, kind of thing, epsom salts are merely a kind of soda and may be beneficial in cleaning some of the crap off the plates - how much ??? I would be lying if I gave an amount. but I can say at least they dont cause any harm that I'm aware of, as I said try hosing out the inside of the battery (wearing sufficient protection obviously - sulphuric acid doesnt like people !) and try to come by some ready mixed battery fill - the acid content should be about three to five percent overall if memory serves me correctly, then charge it slowly on no more than a trickle charge, by the way I subscribed lol
I understand
@@usernamesreprise4068 I want to charge my Ebike batteries
(6 - 72v 20ah) I watched a fews video's at first that used epsum salt & distilled water, most were to flush out and clean the batteries.
Then I found a mechanic's video that demo's adding just distilled water nothing else however his technique is a bit different. He uses high cranking amps (200A) for 15 min. & then rest's the battery for 1 hour.
He repeats this process 5x - 15min On - 1hr Off ..
I don't have a charger that outputs 200A and I doubt many do, so I'm going to add just the distilled water, since there's a little acid left in the batteries, 1/8" above the plates' then use a trickle charger to charge them over night or 16hrs to 24hrs and see how that works.
These deep cycle lead acid batteries are the same used on electric Forklift's and that's all we ever did was add the distilled water at the end of the shift and let it charge over night for the morning shift. THere is a pH tester you can use, I believe it was 4% but when they're being constantly filled it doesn't really matter testing them if the machine is running prop[erly.
Remember to keep your comments respectful or they will be removed!!!
Brother you spent too much time pouring salt you can use funnel would more effective than the spoon with all do respect
If I had a funnel that small I’d used I woulda used it, the 1 I have is bigger than the holes in the battery so I wouldn’t be helping nothin!!
i have seen folks do this in the past. and it takes a charge shows 12 volts. but when a load is put on it ,it dies so i will check to see if you are lucky and have a good battery
It does pretty good, it holds about 12.4 volts & cranks every time, I have done one other battery that didn’t do well but it’s because 2 cells were collapsed but have done 3 so far & 2 out of the 3 did good!!
acid is absorbed into the plates when discharged, so acid never leaves the battery, adding more acid gives an over concentration
Yes & too much acid is just as bad as not enough!! Thanks for watching!!! Please subscribe!!!
Many years ago learned ago I found out how explosive car batteries can be, I had a freshly charged battery at my feet I was cutting steel with an abrasive cutter I had had a face shield on, I heard a loud pop finished cutting I found the top of the battery blown off, I had no injuries I lucked out.
Yes they are dangerous for sure!!! That’s why you wear your PPE
Thanks for watching, please subscribe!! Will be doing some hay cutting raking, & baling videos in a week or so
It’s like every other job you do, it’s dangerous & that’s why you have your PPE & use caution!!!
i noticed no action in the cell at the positive terminal end, in my experience with batteries (20 yrs. ) that cell is bad check with a hydrometer, after the battery cools down
Your right, that cell was bad thus the battery is bad cause that cell collapsed!!! Thanks for watching!!! Please subscribe!!
You are great! Very entertaining as well as teaching a thing or two! Great tip on purified water! PS, Love the chicken walking through the shot!
Yessir I don’t edit nothing out lol!!! There are those that have had negative things to say like I was boring or doing it wrong but if it gets good results then it’s not wrong!! However this battery in the video was in fact a bad battery, I have done 3 so far like this & the other 2 are doing great cranking!!!
@@hattcreekfarm No, you by yourself are very far from boring! You are a blast!!
Lol thanks for watching
I would have dissolved the Epsom salt into the water in the water bottle first, then added the solution to the battery with a small funnel. I'm not a chemist, but believe that by adding the Epsom salt, you're basically adding more sulfate ions to the liquid in the battery from the Epsom Salt (the SO4 in MgSO4). The original Sulfuric Acid in the battery also has the sulfate ions (the SO4 in H2SO4). I have a few dead batteries in my shop that I will try this on. Thanks for the video!
The recipe called for 1tsp of Epson salt per hole so I did it like that, as for the funnel I only had a big one thus the reason I used the spoon, funnel was bigger than the holes so more mess
It worked on the 2 batteries prior but this one gad a collapse cell so no it didn’t on it
@@hattcreekfarm You did it best you could with the tools at hand and I applaud you.
Thank you sir
Thank you that was very informative. I joined ez battery recycling and I'm learning how to recondition used batteries to save lots of money!
It works!!! And you can make a little too!!!
Epsom Salt? How quaint! Everybody has used this before and results are always less than expected. I thought you were coming with something new.......
It is new to me!! And it works, I have 2 batteries that it has worked on, the one in the video didn’t work cause it had 2 cells collapsed together so I melted the lead down into fishing weights
@@hattcreekfarm shoulda recorded one of the successful ones lol idk why u said it worked at the end while its on the charger without load testing it or anything. sorry about the comments maybe turn them off...pray for them,
@@brad3933 don’t know till you try it!! My videos aren’t rehearsed their done live so whatever happens happens
Awesome!! I remember doing this with my papaw and just like you he would turn it into a life lesson.
Yes, I love doing things like this using it for illustration, it helps get the message over better!! Please subscribe!! Thanks for watching!!
Enjoyed the video,especially the devotional. Thanks!
Yessir and please subscribe & tell others about our channel
Did it work?
How long do u charge with the Epsom salt? Then what do u fill it back up with to use when you're done?
Good video thanks...
God Bless
I usually fill each hole with 1 table spoon of Epson salt then put it on charge, watch for the ones that don’t start to bubble then add another spoon full until it bubbles, when you see bubble activity I let it charge overnight, then check it asap that mawnin, no this battery had a collapsed cell I’m assuming because the charger read BAD BATTERY when I went to check it
Thanks for watching, I’ve had success fir 2 other batteries I did so far!!! Please subscribe
Can we use funnels for the distilled water and the Epsom salt?
You can use whatever at your place, my funnels were larger than the holes so I still had to use the spoon
Thanks for watching, please like subscribe
Omg what a plank dont forget your vinigar with your epsom salts 😂
This recipe didn’t call for vinegar
Ive got a deep cycle, I've been wanting to run my pump, gonna give it the ol' Lazarus treatment
@@au_gmentedreality it really works if the cells haven’t collapsed, some folks on here don’t know what it means to keep comment’s respectable & they will be removed, I don’t allow them on my channel!!
@@hattcreekfarm hahahaha
@@lifeisgood3386 lol
i tried before in 5 batters and din't work
I’ve done 3 so far & only 1 didn’t do good & it’s the one in the video, the cells had collapsed, it doesn’t work if the cells have collapsed
I study to show thyself approved. I went behind the Vail, and baptized myself. I am in the many membered body of Christ. I don't go to church the Bible spelled them out. He had 7 churches, 5 he snuffed out because they are nothing other than the sinaguages of Satan. He had 2 he liked and those were Smerna and Philidelphia they entertained and became 1. Hope you don't think you flying away. Put the gospel armor on and in place. Serve the purpose we are here for. 1st taken is by deception from Satan claiming to be God. Yes we are living in the last days of the 6 year creation. Warning it's happening as you read this Truth.
GOD BLESS HIM HE IS TRYING..... l.m.a.offff.😇😇
So slow,,,,,,,
@@DennisRoberson-m3b the process is slow!! Anything with batteries & acid is slow so you don’t get it where it doesn’t belong!!!
This was cool. Never tried the epsom salts trick so I might just have to do that next time. Here in the Texas heat I've had to top off some batteries with acid from the auto parts store in years past but that stuff is nasty. I've also tried the battery repair setting on the charger but thats a hit or miss depending on the type of battery. Anyways, God bless you brother.
Yessir thanks for watching
no followup video
It’s coming, I work doing several things so it’s hard to make videos preparing for hay season & work my regular job & do my hobbies!!
Amen look around at the world its crazy out here
Love the Harbour Freight VOM
Yes, it works great!!!
Please subscribe
The problem is that this trick doesn't always work? often on worn batteries this don't work! People think it works because they don't have a good battery tedters and don't know the condition of the battery.
The car battery is also not designed to run on this white
All I know is, I tried it on my small engine batteries & 2 outta the 3 I did this to worked great & are still working!!! Haven’t done it on car batteries!!!
Please subscribe
I have just subscribed to you
Thanks for watching & subscribing!!!
Apparently there are some folks who can’t read!!! I said keep your comments respectful or they will be removed!!! Listen to the video folks, I didn’t say that distilled & purified water were the same, I said that the big jug & what was in the bottle were the same, because I poured distilled into the small bottle because it was easier to pour from!! Some comments have been removed like I said they would be!!
Looks like a dead cell on the far right?
Yep collapsed
IT WAS ALREADY COLLAPSED BEFORE U STARED THE FIXX@@hattcreekfarm
CORRECT YOU ARE.....YES
Yes I didn’t know that it was collapsed at the time but after it kept heating up on that side I googled I & it said collapsed cell!! They say that some batteries during shipping if they get banged around or dropped this is what the most causes them to collapse!!
My deep cycle boat battery is completely dead ,will this work ?
If no cells are collapsed it should, be safe & wear your PPE though!!
If your derp cycle battery holds a charge good there’s no reason to do this, only reason I did this was it wouldn’t hold a charge but I found out it had a cell collapsed
I put the charger on it and it wo t charge at all
You’ve probably got a bad battery if it won’t charge at all
Very well said friend. I really thank you for your reading on going back to church to get recharged in our mind and spirit. We all need to get closer to God. ✝️
Yes, that is the number 1 priority!!! Thanks for watching, please like & Subscribe, it helps me to keep videos like this on here to keep Gods word flowing!!
you just dump a bunch of salt in there?
No start with a table spoon full at a time to each hole then add more!!!
If you see no bubbles after a few add another spoon per hole
@@hattcreekfarm I'm about a week into trying to restore a 12v deep cycle battery. 1st day was reading 1.8 volts and had a few bubbles in one cell. Now i can get it up to 9volts and there are 3 cells bubbling alot and the other 3 are just now starting to bubble a little bit. The metal inside the three cells that are boiling alot looks brand new and clean. The metal inside the other three cells still looks corroded. How long does it usually take to desulfate every cell? As long as the voltage slowly climbs higher, I assume that it is still progressing and desulfating.
I saw someone put something on RUclips about desulfurization using baking soda but you pour all the acid/water whatever you want to call it out into a container or bowl big enough to hold it all then they poured in a mixture of water & baking soda sloshed it around in the battery (with the caps back on of course) then let it set for some time (don’t remember how long) poured the mixture out then flushed the battery out with the water hose & refilled the battery with poured out contents & charged it!! You can go to google type in how to desulfurization a battery or bring a old battery back to life using baking soda & see where that takes you!!
Thanks for watching, please subscribe
What about the results ? What was the final voltage after doing the chemical additive and charging ? Were you able to place it back in the mower and show that it cranks like a charged battery?
This battery as I’ve commented in several replies, had a collapsed cell which resulted in it not holding a charge, but if you’ll read in these replies I stated that 2 others did great & are still cranking mowers!! Thanks for watching!! Please Subscribe!!
Have you tried changing the polarity of a battery? I haven't done it but have seen others do it to give new life to the battery.
No you never change polarity of a battery it could cause it to overheat & explode!!! The instructions on my charger say to never reverse polarity!!!
Thanks fircwatching
@@hattcreekfarm Before changing the polarity, the battery must of course be completely discharged and the voltage must be 0 volts. Then there is no risk of the battery overheating or exploding.
Ok thanks for the info may try this!! The battery in the video showed charging while I was doing the video but after the 24hr charge cycle my charger showed bad battery on the screen so I assumed it had collapsed cell so I’m just melting it down for the lead
If battery acid was purchased from an Auto store, would that be better to use then charge the battery??
I’m sure it would but not sure, just going by what I’ve seen others do with what they had that I’ve seen work!! You can google it to find out, I don’t have all the answers, just following someone else’s advice!!!
Thanks for watching
Grand pa taught me this epsom salt trick. I wish i could find a way to do this with sealed batteries, and agm. Thanks most of all for the bible verses. God bless sir.
You can prize the top off of maintenance free batteries with a screw driver or small pry bar what I’ve been told, just wear safety glasses & gloves & have a tube of silicone to reseal the top!! Might try this later & docs video
Thanks for watching, please like & subscribe
i thought is was suppose to be distilled water instead of regular water because of the minerals. I'm looking forward to trying this.
It is, I just poured the distilled water in the smaller bottle because it’s easier to pour in the holes
Are you sure sulphuric acid is correct?
Was told the acid is stored in the cells so there’s no need to add more.
Why not use a funnel to svoid spillage.
Have you got one that small? I don’t!!! That’s why I used the spoon!!!
It’s not an automobile battery, the holes are lots smaller on these small batteries
Thank you for the speech, and Amen
Thanks for watching