WHAT IS A MOTOR DRIVER | ROBOTICS FOR BEGINNERS

Get 90 % discount on "HANDS ON ROBOTICS WITH ARDUINO | BUILD 13 ROBOT PROJECTS course" by clicking on the below
www.udemy.com/course/robotics...
In this course I will introduce to the basics of Motor Driver. You will understand the basics of Motor Driver IC i.e
the L293D

[@sippy_cups]

Great video, but the music at the end is way too loud.

[@floriskeune5456]

I was wearing earbuds an it scared the hell out of me

[@ch0ms]

@@floriskeune5456 same XD

[@himalshadharmapala5530]

Thank you .nicely explained

[@teamhydra2789]

Thanks bro it's what is. 👍👍

[@induwaragimhana7312]

Thanks .it is perf

[@vikasma1000]

Helpful video

[@umargul5644]

Well done

[@decent9506]

nice video

[@Willy_Tepes]

Strange question for you since I am doing some strange drone stuff:
How would I manage to control a stepper motor driver like the L293D with a flight controller (FC)?
The small 3-5V stepper motor must be able to stop in a specific location, and rotate both directions with rapid response time. The motor is not moving much mass as this is a small control surface, but there needs to be some degree of "braking" in the motor movement which can be achieved through the FC.
I don't need to keep absolute track of steps moved, but only rotation in degrees. Can I do this with or without position "feedback" from the motor? I may be able to use sensor inputs like the gyro and accelerometer instead of rotaion in degrees for feedback. Can I progam the motor output signals on the FC to do what I need with only PWM? I know only a bit about electronics and programming. If this does not makes sense to you, can you recomend me someone who can answer my question?
I need to get this built because the imaging system on the drone is really cool, like something out of The Matrix.

[@gorlamanishkumarkmqumwuazl2736]

Tnks bro 😁

[@navarasp8000]

from where i can get this driver board [second driver]

[@rohit-gi6wh]

Can't I use voltage regulator Instead of motor driver by using transistors

[@ryaanshaikh360]

Hey if i lost the en1 and en2 caps from the 2nd motor driver will it work

[@biswajitkar5741]

i have same m.driver like the second type.But their are 4 more mail socket (EN1& EN2). in this video which are in blackcolour in trans position of the main chip. please... explain it

[@bharathram4136]

For the second motor driver how can i give enable signal so that u can use PWM

[@kaushalsorte9870]

Yes I have the same question. Are the pins that are covered with caps the Enable Pins?

[@GaneshJadhav-kn8mb]

Can it run the motor in reverse and forward mean does it amplify current for forward and backwards??

[@nimishkhattar2017]

How many motors can we connect to one socket containing 2 holes?

[@tonysicily2687]

A great explanation, but I am still confused as to why this is this better than using a relay module.

[@krishmittal2517]

what if my board does not have vcc

[@amoladep]

Can I connect stepper motor instead of dc motor?

[@prasad6217]

Amol Adep There is usually a different motor drivers for stepper motor

[@nil870]

Sir how to make 3 phase motor driver?

[@souhailahmed8146]

Isn't the phase system for ac current bro

[@satendrabhardwaj7896]

There is loss in voltages

[@aklapotherpothik9056]

How to make micro motor driver

[@BalwantSingh-cs7vj]

Hi

[@pranitadhikary5732]

Can i CONNECT MOTOR DRIVER WITH RF Wireless Encoder & Decoder Board With HT12D & HT12E IC ????

[@alokawasthi1478]

i dont think uh can connect it directly. uh will need a microcontroller for the purpose. so receiver -> HT12D -> microcontroller -> motor driver -> dc motor

[@AnilKumar-ks8wb]

Hindi bol angrej