In this video you will know why soft stater use, and it's circuit diagram also about NTC and Resistance type soft starter circuit diagram drive.google.c...
Sir i think it is not the back emf. The main reason is "impedance". Impedance is like a load which can be seen by inductor loads(like transformer or motor)when they ar connected to AC power supply. Impedance only can be seen in ac current not in dc because for DC impedance of a inductor is zero. The main reason we use soft starter is to slowly charge the big heavy supply capacitors,because they consume a lot of inrush current. Hope this information is useful. And it is also a Nice video 👍❤️
capacitor is not the main reason, transformer core saturation / delay in ac impedance generation is the main reason. in other words, back emf isn't too wrong. 😑
Bahut sundar explanation hai Sir. Sach hai aapki videos se ideas generate hote hain. Jo followers thode bhi technical hain unko apne kaam ki information mil jaati hai aapki videos se.
Sir apne jo 3000watt wala circuit diagram bataya tha main usme output main 12pair njw0281 and njw0302 transistor lagana chatahu. To mujhe kitne volt or kitne amp ki transformer lagana chahiya. Jesse mera transistor safe rahe or asshi output de sake. Plz sir reply digeaga 🙏
Sir passive crossover design pe full detail video bnaye or sath me amplifier ke output watt ke hisab se network plate me kitne ohm or watt ke resistance lagege speaker or hf ke watt mach Karne me
sir according to the diagram i build it and it is working ( I did not connect to the transformer. ) but wanted to check whether it is OK, and it is ok. but one problem is that is 220 ohms 2 watt why it is getting hot. ( before connecting to the transformer ) after connecting to the transformer the output secondary reading is showing correctly 24 0 24 but 220 ohms is becoming hot pls help
Sir mene 4pcs salcon k 5 pair 5200/1945 k amp hook kiye hai for low pass subwoofer , usmay se ek amp on/off me thump karta hai , kya ye SOFT START use kar k thump remove hoga ?
Sir bohut si amplifier pe speaker output pe fuse lagaya jata hai protection ke liyea but uspe kuch likha nehi he to fuse kitna Ampere ka hai vo kaise pata kare amplifier board ke hisab se.
soft started ko 12v 18v 24v ko transformers laga sakta hei amplifier ko switch on karthey hee starting sound hata hei like mere pas yamaha hei on karaney se no sound if i hv to use 12 0 transfomer dp i hv to use 12 v relay pls explain
Dear friend any electrical or mechanical equipment will have in rush current( in mechanical it's something else) even nion lamp will have in rush current. After stability the current will be much less. FYI PL. ITS NOT THAT SMALL MOTORS DONOT HAVE IN RUSH CURRENT. EVEN a 0 .1 hp motor will have. Accordingly we have to use switch gear. Pure resistive load will also take higher current. Normal 100w bulb , heaters pl check. No way we can escape from starting load if you want 100 percent of efficiency right from beginning.
Thank you so much sir aapke soft starter diagram ke liye Sir main aapka बहुत-बहुत dhanyvad karta hun Kyunki aapka 500 watt diagram Ko Dekhkar Maine 500 watt ka emplifier Banaya jo ki bahut hi lajawab banaa hai aur Sir main aapka phone number chahta hun Meherbani Karke dijiyega please Kyunki Main DJ ka kam karna chahta hun Ek company kholna chahta hun usmein Sir main aapko chief guest banana chahta hun Sir main speaker bhi Khud assemble karta hun aur Transformer bhi Khud winding karta hun sound box bhi Khud banata hun
Dada spikar potaksan jo pcv bayana tha,ham na banaya,kam to kor raha ha .lakin sarkit sa mach nahi kor raha ha.4148 didod 2n5401 ka bas ma na lagaka e ma laga dia.
Q - ट्रांसफार्मर के प्राइमरी सेक्शन पे input voltage २४ v DC fix कर दिया तो फिर आउटपुट पे required dc voltage कैसे मिलेगा ? आपका यह circuit ( same as led driver circuit ) ac को dc पे convert कर देगा , क्या २४ v relay dc को ac में convert कर देगा ? 🙏❤️
Aapne sahi kaha ki relay bhi inductive load hai lekin dc dene se kyo nahi jalti? Kyoki relay me bahut hi patli wire se winding hoti hai is liye usme winding resistance add ho jata hai, dc voltage dene se winding resistance ke karan current limit me rahta hai aur winding nahi jalti. Agar aap us relay ko 80v ac volt denge to bhi nahi jalegi, lekin dc 80v dene.se coil jal jayegi.
Sir i think it is not the back emf. The main reason is "impedance". Impedance is like a load which can be seen by inductor loads(like transformer or motor)when they ar connected to AC power supply. Impedance only can be seen in ac current not in dc because for DC impedance of a inductor is zero. The main reason we use soft starter is to slowly charge the big heavy supply capacitors,because they consume a lot of inrush current. Hope this information is useful. And it is also a Nice video 👍❤️
Absolutely correct
capacitor is not the main reason, transformer core saturation / delay in ac impedance generation is the main reason.
in other words, back emf isn't too wrong. 😑
Bahut sundar explanation hai Sir.
Sach hai aapki videos se ideas generate hote hain.
Jo followers thode bhi technical hain unko apne kaam ki information mil jaati hai aapki videos se.
ruclips.net/video/8r6144aI8Ko/видео.html
Electronic device full details
very good video nice explen sir thank you👌👌👌👌👌
Thank you sir mujhe aapki ISI video Ka Intezar tha very thank you sir
sir very much use full circuit diagram .good job....... thanks .
🙏🙏सर नमस्कार साफ्टस्टार्टर के बारे में जानकारी देने के लिए बहुत बहुत आभार🙏🙏
Guru ji very good information
Aap ka sukriya hame explain k liye😊
Excellent video 🎉🎉🎉🎉
Importent topic think you sir
Bahut achha samjhaya aapne
Bhut hi अच्छी vido
Thanks for knowledge
Bohut acha sair.
Dhanyvad Sar bahut acche
Good tiching karte hai 👌👍👍👍👌
Thank you sir ji.......aap ek baar bass baising volt ko details se smjhaiye plz
कितनी आसानी से सॉफ्ट स्टार्टर का कंसेप्ट और डायग्राम समझा दिया । मजा आ गया
👍👍👍
मैक्सिमम कितने वॉट तक इसका उपयोग कर सकते हैं?
5000w tak ke amplifier me
@@AmplifierWorld 😱😱😱
It's Very useful and unique
Thank you for sharing sir ji ❤️
🕉️🙏🙏🙏
Aapki video ka besabri se intzaar karte hain..sir.....
Plz sir bass bising volt ko bhi details me smjhaiye
Sir apne jo 3000watt wala circuit diagram bataya tha main usme output main 12pair njw0281 and njw0302 transistor lagana chatahu. To mujhe kitne volt or kitne amp ki transformer lagana chahiya. Jesse mera transistor safe rahe or asshi output de sake.
Plz sir reply digeaga 🙏
Informative tutorial 🙏❤️ description pe schematic upload kar dene se humlog is circuit ko bannane ka kosish karte
Very very important topic, thanks
Very good presentation thanks
Very nice video sir 👍 👏 👌
App ko thanks sir,
Very good sir
Very nice
Simple & nice diagram.
Hi, This circuit working well. But the 220 ohm resistor is overheating. How this fix it. I used 5w resistor.
Good 😊😊😊😊 job
Good job
Good knowledge sir
ruclips.net/video/8r6144aI8Ko/видео.html
Thank you sir ,for this video.
Thanks for the vedio
Good morning. 👍👍👍
Sir passive crossover design pe full detail video bnaye or sath me amplifier ke output watt ke hisab se network plate me kitne ohm or watt ke resistance lagege speaker or hf ke watt mach Karne me
Thanks Sirji
sir according to the diagram i build it and it is working ( I did not connect to the transformer. ) but wanted to check whether it is OK, and it is ok. but one problem is that is 220 ohms 2 watt why it is getting hot. ( before connecting to the transformer ) after connecting to the transformer the output secondary reading is showing correctly 24 0 24 but 220 ohms is becoming hot pls help
aprox. 70ma is flowing through ckt. around 1.1w power across resistor. so it is normal.
Very nice explanation sir..
ruclips.net/video/8r6144aI8Ko/видео.html
Ek request hai industrial ya home use wale SMPS ki repair ki kuch knowledge share kare sir.
ruclips.net/video/8r6144aI8Ko/видео.html
Smps power supply repair
Sir mene 4pcs salcon k 5 pair 5200/1945 k amp hook kiye hai for low pass subwoofer , usmay se ek amp on/off me thump karta hai , kya ye SOFT START use kar k thump remove hoga ?
Use speaker protection, it will provide delay
@@AmplifierWorld thanks sir
Sir bohut si amplifier pe speaker output pe fuse lagaya jata hai protection ke liyea but uspe kuch likha nehi he to fuse kitna Ampere ka hai vo kaise pata kare amplifier board ke hisab se.
Sir 105 value ka badla or konsa value ka capasitor use kar sakta hu..
Sir ho saka to iska upar ek details or practical video banaiya na please...
Behtarin video👍
Thanks for sir
soft started ko 12v 18v 24v ko transformers laga sakta hei amplifier ko switch on karthey hee starting sound hata hei
like mere pas yamaha hei on karaney se no sound
if i hv to use 12 0 transfomer dp i hv to use 12 v relay pls explain
you can use 12v relay with 12v transformer and 12 v regulator. for speaker click sound you can use dc protection and delay on ckt for speaker.
Very nice 👌
classic sir👌
👍
kafi Emportent information
Super
Nice
nice
Good information thanks
Very nice Sir
Dear friend any electrical or mechanical equipment will have in rush current( in mechanical it's something else) even nion lamp will have in rush current. After stability the current will be much less. FYI PL. ITS NOT THAT SMALL MOTORS DONOT HAVE IN RUSH CURRENT. EVEN a 0 .1 hp motor will have. Accordingly we have to use switch gear. Pure resistive load will also take higher current. Normal 100w bulb , heaters pl check. No way we can escape from starting load if you want 100 percent of efficiency right from beginning.
Sir आप ने कहा से amplifair का काम सीखा है बिल्कुल एक शिक्षक की तरह बताते हैं
Sir, NTC type circuit me NTC kaha pe fit hoga?
Resistance ki jagah
sir mere pas Sony ka 40 0 40 v 5 Amp transformer h is me kya ye soft start lgana prega
Nhi
Sanjay Ray sahab ne jawab de diya
❤
Sir 220ohm resistance hit horaha hai🤔🤔 keya karu?
Jai hind sir
NTC Laga diya hai bhi kya sem results milenge sir
Mujhe 400 watt ka sircut banna hai help chahiye apki
Sir ji ptc ke jagah ntc lga skte hai kya
No
Thank you so much sir aapke soft starter diagram ke liye Sir main aapka बहुत-बहुत dhanyvad karta hun Kyunki aapka 500 watt diagram Ko Dekhkar Maine 500 watt ka emplifier Banaya jo ki bahut hi lajawab banaa hai aur Sir main aapka phone number chahta hun Meherbani Karke dijiyega please Kyunki Main DJ ka kam karna chahta hun Ek company kholna chahta hun usmein Sir main aapko chief guest banana chahta hun Sir main speaker bhi Khud assemble karta hun aur Transformer bhi Khud winding karta hun sound box bhi Khud banata hun
Aapke pyaar aur mohabbat ke liye dhanyawaad
Hii sir im from tripura india
Thankyou sir ji
Dada spikar potaksan jo pcv bayana tha,ham na banaya,kam to kor raha ha .lakin sarkit sa mach nahi kor raha ha.4148 didod 2n5401 ka bas ma na lagaka e ma laga dia.
Thank you sir 🙏🙏
Sir maine sonodyne amplifier itne defferent kyu hote hai please ek video bna do sonodyne amplifier is topic per
4700....35.volt ka candensar lag sakta hai ?
Lag jyega
Sir power amplifier pr video banaye
sir 40 ohms 20 ohms not available but 47 ohms 5w × 4 is it ok
@@ronaldfernandes5697 47ohm 5w
2 piece can be use in parallel connection
Thanks sir.
Sir 12 volt ka realy use kar sakta hu ka...
Yes lekin 105 ki jagah 334 use kijiye
Thanks
Ac mai line aur neutral ka input line agar nahi pata hai konsa kya hai tab input kya kare
Thanks sir
Thank you sir 😊👍
गुरुजी जय श्रीराम 1000 watt amplifier me soft starter ntc ki valu kya laganar kya resistance nikalje ntc lagana hai
Resistance wala bhi work karta hai, and low power amplifier me resistance based soft starter lagana thik hai
@@AmplifierWorld ok sir
sir 24v relay is not available i use T type relay 12 v T type relay 12 v zenor
Ofcourse
Q - ट्रांसफार्मर के प्राइमरी सेक्शन पे input voltage २४ v DC fix कर दिया तो फिर आउटपुट पे required dc voltage कैसे मिलेगा ? आपका यह circuit ( same as led driver circuit ) ac को dc पे convert कर देगा , क्या २४ v relay dc को ac में convert कर देगा ? 🙏❤️
Relay to only by paas ke liye lagai hai
Delay time ke saath
Iska dc ya ac se koi lena dena nhi hai
Agra me chipitola bajar me old rajitens or trajitar 3773 .3055 and Adar pards mil jati he Philips ke old amplifier bhi milte he
Nice sir
Thank you sir
ruclips.net/video/8r6144aI8Ko/видео.html
Sir Ji mera 220om 1watt ka resistence bahut garm ho raha hai
Sir ji relay bhi to ek transformer ki tarah hi he phir wo dc current se kese operate ho jata he
Aapne sahi kaha ki relay bhi inductive load hai lekin dc dene se kyo nahi jalti?
Kyoki relay me bahut hi patli wire se winding hoti hai is liye usme winding resistance add ho jata hai, dc voltage dene se winding resistance ke karan current limit me rahta hai aur winding nahi jalti. Agar aap us relay ko 80v ac volt denge to bhi nahi jalegi, lekin dc 80v dene.se coil jal jayegi.
Sir magnet charger machine ka 1500watt ka diagram video daliye sir
Sir, tda 2050 ka bridge mode circuite banaiye...please
First
Aapki first comment ka Swagat hai
सर मूंदे ९ चानेल का मिक्सचर केबिनेट चाहिए कैसे और कहां से मिलेगा ?
आप ऑप एम्प आई सी में बैलेंस्ड इनपुट और बैलेंस्ड आउटपुट सर्किट को प्रीएंप्लीफायर के रूप समझाइए।
Sir CA 20
Sounds staderd ka madual
Ka pura digaram bnao
Diod kunsa lagaye
Sir app ki आवाज pahle fm rediyo चैनल पर एक अमीन सेयानी नाम के उन्हीं की तरह आप की आवाज है
Soft start+high voltage cut off banaye.
Sir zenner diode ka number boliye plz ?
24v
3915 ic का vu मीटर बनाए
Practical please sir