Fiddling with the dials trying to get signals to be understandable is half of the fun when using a Regen. Not the best radios for casual listening, but lots of fun.
Many years ago I had a 2-transistor arrangement courtesy of a kit, possibly made by Philips and on just a ferrite rod was surprised how well it pulled in the stations. By comparison, the battery tube radios I made in the early 60s needed an outside antenna to do something similar.
what are the Values for L2-MW and L2-SW ?. The question is based on the very high possibility that my ferrite rod might have different properties than yours and will yield a value that will not get me to the correct bands. Withe value I can build my coils very close to what you have in yours.
@@dz-abouttechnique1849 minute 03 has only the amount of turns and the diameter of the rod, but not the inductance value in Henry's..(thanks for the quick reply, I have already completed most of the work just needed to verify that the inductance of K2 was close enough to response correctly
Salut !Fain proiectul!De unde ati achizitionat modulele de amplificare.Cele pe care le-am cumparat au probabil un factor de amplificare de mai putin de 20 de ori cu toate ca ar trebui sa fie 200.
Salut! Este constructie proprie. Am incercat tot felul de variante constructive, pana am ajuns la forma de la minutul 8:59. Am incercat si cu 3 etaje de amplificare, insa montajul devine prea sensibil, probabil trebuie realizat intr-o carcasa metalica.
@@dz-abouttechnique1849Mă refeream la amplificarea audio. La minutul 9:02 se vede ceva care seamănă a modul de amplificare audio lm386 ... Dar oricum e frumos radioul! L-am constituit și pe cel cu "reactie" AM și am reușit să îl fac să meargă. De fapt am făcut vreo 3 . La cat mai multe videouri!
It's amazing what you've done with so relatively few components.
Thank you!
Fiddling with the dials trying to get signals to be understandable is half of the fun when using a Regen.
Not the best radios for casual listening, but lots of fun.
That is why a superheterodyne is in the works.
Rapaz gostei do seu projeto muito bom e o receptor te um ótimo potencial incrivel
Muito obrigado!
Nice proje.
@@arifceylan3730 Thank you!
Many years ago I had a 2-transistor arrangement courtesy of a kit, possibly made by Philips and on just a ferrite rod was surprised how well it pulled in the stations. By comparison, the battery tube radios I made in the early 60s needed an outside antenna to do something similar.
👍
Excellent project 👏
Thank you!
I love the Manhattan style breadboard/components!
Thank you!
Sơ đồ này ra đời cách đây thập niên 60,70 của thế kỷ trước thì ứng dụng rất hay... giờ không thông dụng chỉ là đam mê điện tử thôi..
Really.
excelente buen tabajo no savia que podias usa ese circuto asi muy bueno
Thank you!
It's amazing, impressed.
Thank you!
Very nice project!!
Thank you!
Awesome . Great work 👍👍👍👍
Thank you!
Wah nyasar kesini kang jenall tok hehe
Boa noite. Me tire uma dúvida por favor. O T1, poderia usar também o BC 548, 2n2219? Obrigado.
Teoricamente... sim. O receptor provavelmente ficará instável.
@@dz-abouttechnique1849 Boa noite. Em SW sintoniziu a banda de 40Metros? Radioamador.
Very informative video
Thank you!
I’m curious. Why did you use a potentiometer and not a variable capacitor to control the regeneration setting?
Read the description.
Hello, very nice.
Where is the diode detector?
Or is it integrated with the amplifier chip?
Audio signal detection is performed by transistor T1.
@@dz-abouttechnique1849 Thank you very much
@@نايفالاحمدي-ي3ض 👍
what are the Values for L2-MW and L2-SW ?. The question is based on the very high possibility that my ferrite rod might have different properties than yours and will yield a value that will not get me to the correct bands. Withe value I can build my coils very close to what you have in yours.
Details: minute 0:03
@@dz-abouttechnique1849 minute 03 has only the amount of turns and the diameter of the rod, but not the inductance value in Henry's..(thanks for the quick reply, I have already completed most of the work just needed to verify that the inductance of K2 was close enough to response correctly
@@dz-abouttechnique1849 L2 not K2, sorry for the typo.
@@noelrodriguez I don't have an inductance measuring device. I estimate as follows: L2 MW: 550 - 600 uH. L2 SW: 10 - 12 uH.
Good luck!
@@dz-abouttechnique1849 thanks, I will add more turns and test, removing some as i go till they are in range..
can this receive ssb-lsb-usb and if so does this have a BFO? thanx
From experiments, it works between 500 Khz and 7 Mhz.
Seçicilik Nasıl ? Komșu istasyon Karıștırması Yapıyormu ? 🤔
İstasyonlar çakışmıyor. Mümkün olduğu kadar çok istasyonu alabilmek için bir anten gereklidir.
Inget masa lalu
Sure.
What did you use to scribe thru the copper?
Cutter.
I have a question
What is the range of mw and sw that we can receive with this radio????
Pleas answer
MW/SW maximum 2000 km.
This device has excellent performance: ruclips.net/video/ApwX6qniuos/видео.html
please give details how make L3 RFC coil by resister
Resistor 100 k + 20 turns. Minute 0:10
رائع
Thank you!
NİCE proje.
Thank you!
Its SSB yes?
What tool was used to cut the grooves?
Cutter. Good luck!
Salut !Fain proiectul!De unde ati achizitionat modulele de amplificare.Cele pe care le-am cumparat au probabil un factor de amplificare de mai putin de 20 de ori cu toate ca ar trebui sa fie 200.
Salut! Este constructie proprie. Am incercat tot felul de variante constructive, pana am ajuns la forma de la minutul 8:59. Am incercat si cu 3 etaje de amplificare, insa montajul devine prea sensibil, probabil trebuie realizat intr-o carcasa metalica.
@@dz-abouttechnique1849Mă refeream la amplificarea audio. La minutul 9:02 se vede ceva care seamănă a modul de amplificare audio lm386 ... Dar oricum e frumos radioul! L-am constituit și pe cel cu "reactie" AM și am reușit să îl fac să meargă. De fapt am făcut vreo 3 . La cat mai multe videouri!
Aha. Scuze. Am ramas blocat pe frecventmetru 😂. Intr-adevar este cu LM 386. Multumesc!@@instructoruldemeditatie2367
Very good
Thank you!
Je voudrais avoir le schéma s'il vous plaît
You can find the diagram in the video.
How to switch between waves There is no switch in the circuit diagram
The MW coil (90 turns) is replaced with the SW coil (20 turns).
@@dz-abouttechnique1849hey which guage wire have you used sir?
details: minute 0:12@@awaismushtaq5719
L3 if done in a small rounded ferrite core or plastic pen refill as inductor their was any problem in reception??
Not. The coil is not important. It also works without a coil. Use a 1 - 100 ohm resistor.
Tape recorder make diygram
👍😎
Thank you!
Falta sintonia fina ...
Esquema simplificado para iniciantes.
in NAME this video reWrite ... #Regenerative
Es mentira no sirve
Cómo llegaste a esta conclusión? 😨
Very informative video
Thank you!