If you want to learn how to perform basic service on your car, this full collor book is the best you can get! www.amazon.com/Your-Care-Companion-Clint-Hightower/dp/1517466946/ref=sr_1_1?ie=UTF8&qid=1493398557&sr=8-1&keywords=your+car+care+companion
Sir I want to thank you this video has been beyond educational. I want to thank you for taking the time to calmly and simply explain what is going on. You have been an immense help to this project.
Can you not just set everything to top dead center before taking the timing belt off? Then as long as you don’t move anything but everything back together as you found it including the camshafts because shouldn’t the cam shafts alignment marks be lined up perfectly whenever the engine is at top dead center?
Yes you can, but why would you want to? It make if very hard to double check to make sure the timing is correct. You could damage the engine and for what? too much risk for no reason.
I read somewhere if taking the cam shaft out with engine in tdc you could bend a valve when installing the cam back in again as when your tightening the bolts for the cam it compresses the valves and a valve could open which piston 1 could hit into if the valve was to open whilst tightening the cam down? Was told it's best to set everything tdc and remove but when installing the cam back in you should rotate the crank 90 degree left or. Right so piston 1 isn't all the way up. Ones the cam is torqued back down then you can turn the crank back 90 degree and fit the rest of the car back together. It ensures no damage to valves etc. What do you Think to this theory?
Very very good instructional how-to-do-it video! Thank you so very much, dear, sir, for this fine help you are sharing and giving with us Toyota owners! Wishing immensely richly blessing from God and stay blessed! Best regards from Sweden!
Just checking to see if you caught my question in the discussion below? I would like to hear your opinion, since the rest of what I have seen of your videos indicate you are quite knowledgeable. Thanks.
Clint, thanks for the video. It helps, as I am putting my 1994 Celica ST back together. At present time am trying to put a rebuilt head on its 7AFE engine block, but realized that the camshafts are in the way of the head bolt holes, so the camshafts have to come out first. The manual instructions say that the service bolt screws in to the two gears (one is called a sub-gear) of the intake cam, and pulls them together to squash the spring inside, to remove as much thickness as possible so you don't mess up the head or cam material, breaking or scarring either one when pulling out. They say you MUST bring out and put in the camshafts holding them perfectly level. I am having trouble getting the two gears lined up for the service screw to catch he threaded gear, and will try to buy that spanner you used, thanks. I hope it works. Maybe it would be helpful to future readers if you posted the name of the tool, with a link to a source. Way down in the comments, I found you had posted a link. It now leads to an eBay error page.
Thanks for your comment Bill. The reason they say lift the camshafts out level is so you don't crack or break one. They are very brittle and when loosening their bolts loosen a little at a time so that the cams come up even, you don't want any stress on them or you can easily break one.
Hello again Clint. I received the tool you suggested, the "Pin Pliers." Now, I am using those pliers, to try to turn the sub-gear clockwise while holding a cresent wrench on the flats of the camshaft and putting my maximum force into the effort, but just cannot get the sub-gear to turn any, so cannot line up the hole to insert the bolt to pull the two gears together on the intake camshaft. The repair manual states that this bolt MUST be installed before attempting to remove the camshaft. Remember, I am attempting to remove the camshafts from a re-manufactured head for my 7AFE engine, so the two cam sprockets (gears) are meshed and the camshafts are still bolted in with 4 caps each. Only the intake number 1 cap has been removed, nothing else. Given that assembly, should the sub-gear be able to turn the slight amount needed to line up the holes? Is it just that I am not applying enough torque? Maybe a bigger, stronger man could do it? BTW: the 1994 Celica ST manual specifies the intake camshaft for this 7AFE requires a 6 mm 1.0 bolt of from 15 to 20 mm length. You said yours was a 10 mm bolt. The threaded gear is the thicker one, so I think I would have to screw the bolt from the other side than you showed in your video, i.e., the sub-gear side, to pull the two gears together so the shaft can be eased out. @@Engineerboy100
@@billcowhig5739 If the gears are still engaged, you don't need the tool, the hole is already lined up. You only need the tool if you take the cams out and forget to put the screw in before removing them.
Clint Hightower today, I have finished the installation of the camshafts on my sisters Cuore. As feedback: this video does also applies on that 3 cilinder EJ-VE engine. Camshaft lobe facing to the front of the verhicle (with engine at timing positions), timing marks on the gearlinkage and the springloaded gear with a set screw (Daihatsu is M5~8mm though). Again, many thanks and a happy and great newyear!! Hero
What a great video! I watched mainly to confirm the bottom timing marks before I take the t-belt off and this shows everything so clearly. One thing I don't understand is why the Haynes manual goes through a whole rigamarole involving the #1 cylinder based on the position of the distributor rotor, which seems totally unnecessary since these marks show everything and you're in there looking at them anyway. Why mess around with the distributor if you don't need to?
Hello Mr. Hightower. Can you do a video on replacing the camshaft seal on the 93-97 1.8 7afe engine. You seem to take the most time explaining things in detail. My 96 Corolla dx has 363k and still going strong. Thanks.
Finally a through explanation I really appreciate this maybe I can get the car to start now thanks buddy for taking the time, I knew the lobes needs to point somewhere specific
hey sir thank you for all the explanations...but could you do me one favour...is the stock camshaft sprocket really adjustable...if it could can you show me how to adjust please...my car is very slow to gain speed even my timing engine is correct.
@@Engineerboy100 I have a ticking sound and it seems near the intake manifold. I know injectors make some ticking noise but on what I am hearing it is a bit louder and it is coming near the intake manifold.
This video has been extremely helpful. Thank you. Question; On my 7AFE 1.8L with 140K turns out the Camshaft bolt backed out 1/2 in and the Knock Pin dropped out. I did find it. It must have slapped against the wheel groove widening it by a few mm. About 3to4mm of slap. So wil replace the Top Timing Wheel for sure. Do you think I would need to replace the Exhaust Cam as well? Im looking for a new knock pin but I believe it's sold with the Cam only.
There's no way for me to be able to know if the exhaust camshaft needs to be replaced or not. One rule of thumb I have found to be true with camshaft damage, they don't usually "bend" they are fairly hard and a little bit brittle. usually camshaft damage is they either crack or they don't.
Thank you Mario, I'm glad you liked it. I explain things in my book the same way, you should down load it here for free or you can purchase a hard copy on Amazon. Have a great day!
Is this cam shaft installation the same for the 4AGE Blacktop? At TDC, shouldn’t the cam lobes over No. 1 cylinder be pointing toward each other, not pointing towards the front of the car like what you have shown in this video?
Hi sir,i have a cuestion...the book for toyota four runner use the two points dot marks to do the head gasket replacement.what to do if the dot marks are aligned but the little hole of the cams is like 5 o clock instead at twelve o clock. I hope you understand my broken English.
It means you are probably 180 degrees out of time. You are trying to time the engine on the exhaust stroke and it needs to be on the compression stroke. Turn the engine over one more time manually, by hand and try it again and the marks should align. and yes your English is fine.
Thanks for replied.im doing a head gasket job, the timing belt is not in place,it's posible to rotate the camshaft using the bolt and rotating it to the right? Or it's better to dissamble and start over again.
How do I know if I’m 1 belt tooth forward or back, off? When I align the camshaft holes with the camshaft pulley hole and crank to 0 my belt is in 1/2 tooth of the belt. I’m not sure if I should move either the camshaft or crankshaft forwards or backwards to align with the belt tooth… Any help appreciated thank you for the video as well!
@@Engineerboy100 the dots on the cam were aligned and the crank was aligned at tdc, just it aligned at a half tooth so either I had to go a bit back or a bit forwards to fit the sprocket groove. Ideally I think it’s on time now just the extra 1/2 - 1 second of starting. Before I’d turn the key and it would fire almost instantly, so I do believe either I’m off a bit or the parts are new and it’s tighter. I think more so I’m off a bit, first time doing a timing belt.
The service bolt is for holding the spring tension of the sprung sprocket so you can get the gears to mesh. If you assemble the engine without the spring tension of the cam gears, they will rattle quite noisily.
How can I remove the bottom timing belt sprocket? I tried prying a little with screw driver. Not much area to pry. I was planning to replace the seal behind there.
Here is a free copy of my book. Check out the Trouble Shooting Chapter especially, download pdf from my Dropbox. www.dropbox.com/s/mcwpv0rb7lun038/0%20Entire%20book%20with%20covers%20and%20QRC%20for%20eBay.pdf?dl=0
Man i sure appreciate u and this video. Lol.. Im doing head work on this same engine. I thought it was a sohc to i took the valve cover off and it was a dohc. Man u save me. Lol. Greatly appreciate it..
i have a 1mzfe am putting back together. the spring gear is what im confused about. the 1mzfe doesnt have a set screw, so where should the spring gear line up? I can make it so you can partially see through the hole or i can turn it some and make it so i cant.
I'm not sure what the thread pitch is on the 1MZFE, but a common bolt is the typical 10mm, test the threads with a few bolts to figure out what the thread pitch is or you can cheat and look in the shop manual for your camry or whatever your 1MZFE is in and it should tell you. or you could call the dealer and ask, sometimes they are helpful.
Thanks for the quick response! i have both heads off and both dont have set screws on either of the the given cams. So you are saying its suppose to have set scerws there? not sure if im the first one to rebuild this but it was running fine without the set screws whole time ive had the vehicle.
i just looked at it this am. the cam with the spring gear can be moved to 3 diffent teeth, if that makes sense. probably the middle one is the right one?
I replace my Toyota corolla 1.6 2000 model cylinder head gasket, set timing and everything but the engine crank but don't start. I replace ignition coil, spark plug wires.
Hey I’m working on 2002 tundra 3.4 liter v6 5VZ. Been stuck for bout 4months . Trying figure out if I got cam gears set rite if the timing is rite . I’ve been watching your video over over . I’m not quite sure if my timing is rite . Oil pan is still off I could send picture video if it would help you to better understand .
I’m trying do same thing to the motor like your video same concept . I’m just thrown off by . Your corolla had two cam gears which in my case I have two sets . And that’s where I’m assuming Why I’m not able to understand clearly.
Clint Hightower yeah I purchase one from advanced Haynes manual . I wanted to get the dealership manual price for the knowledge is reasonable n fair for the info it contains . Not able to afford it yet. But hey thank you . Least you took the time to reply with honest advice .
The 1994 doesn't have a separate CPS, only OBD2 (95.5-96+) 4afe/7afe have a crank position sensor for determining cylinder misfire. It's part of OBD2 emissions self diagnostics. 94's rely on a cam position sensor that is inside the distributor.
Yes. That ticking sound is your lifters. Toyota's have solid lifters and can only be adjusted by replacing shims. the thickness of the shims establish the distance of clearance between the camshaft lobes and the lifter "discs" there are specs the manual and you have to measure the clearance with a feeler guage ... it is not a beginner project .... read up on this more before attempting.
TurboFo_Oil_Changer Porsche_Light_Saver thx for quick reply, you know where I could find the manual online as I bought the car and the previous owner did not have the manual
Clint Hightower I just replaced the cylinder head on my tacoma 3rz and could not figure out why it was making noise at idle and also slightly misfiring. I guess the backlash was just enough for a slight misfire, Thanks to your video it runs 100% now thanks a ton happy new year ✨
You should get all of your torque spec . information from your shop manual, never trust someone telling a torque value on an importing internal engine component. If that is how you get your torque information, you should not be building engines.
If you want to learn how to perform basic service on your car, this full collor book is the best you can get!
www.amazon.com/Your-Care-Companion-Clint-Hightower/dp/1517466946/ref=sr_1_1?ie=UTF8&qid=1493398557&sr=8-1&keywords=your+car+care+companion
Clint Hightower this was awesome, you speak in such a clear voice
Clint Hightower hi sir where can I buy that tools please thank
Can you tell me right or left on the hydraulic balance and that's the what is it harmonic balance to take it off thank you
The marks on the exhaust cam on the front vs back are going to be after you put the bolt in it correct?
That you sir 6yrs on and still helping people, helped me on my 2tz I appreciate it ❤️
Yep, love helping people. Thank you for your encouraging comment.
Sir I want to thank you this video has been beyond educational. I want to thank you for taking the time to calmly and simply explain what is going on. You have been an immense help to this project.
" very clear" instructions of this procedure!!!!!!!!!!!!!!!!!!!!!!!!! and the video was great!!!!! thank you!!!!!
Can you not just set everything to top dead center before taking the timing belt off? Then as long as you don’t move anything but everything back together as you found it including the camshafts because shouldn’t the cam shafts alignment marks be lined up perfectly whenever the engine is at top dead center?
Yes you can, but why would you want to? It make if very hard to double check to make sure the timing is correct. You could damage the engine and for what? too much risk for no reason.
I read somewhere if taking the cam shaft out with engine in tdc you could bend a valve when installing the cam back in again as when your tightening the bolts for the cam it compresses the valves and a valve could open which piston 1 could hit into if the valve was to open whilst tightening the cam down?
Was told it's best to set everything tdc and remove but when installing the cam back in you should rotate the crank 90 degree left or. Right so piston 1 isn't all the way up. Ones the cam is torqued back down then you can turn the crank back 90 degree and fit the rest of the car back together. It ensures no damage to valves etc. What do you Think to this theory?
Very very good instructional how-to-do-it video! Thank you so very much, dear, sir, for this fine help you are sharing and giving with us Toyota owners! Wishing immensely richly blessing from God and stay blessed! Best regards from Sweden!
Just checking to see if you caught my question in the discussion below? I would like to hear your opinion, since the rest of what I have seen of your videos indicate you are quite knowledgeable. Thanks.
Clint, thanks for the video. It helps, as I am putting my 1994 Celica ST back together. At present time am trying to put a rebuilt head on its 7AFE engine block, but realized that the camshafts are in the way of the head bolt holes, so the camshafts have to come out first.
The manual instructions say that the service bolt screws in to the two gears (one is called a sub-gear) of the intake cam, and pulls them together to squash the spring inside, to remove as much thickness as possible so you don't mess up the head or cam material, breaking or scarring either one when pulling out. They say you MUST bring out and put in the camshafts holding them perfectly level.
I am having trouble getting the two gears lined up for the service screw to catch he threaded gear, and will try to buy that spanner you used, thanks. I hope it works.
Maybe it would be helpful to future readers if you posted the name of the tool, with a link to a source. Way down in the comments, I found you had posted a link. It now leads to an eBay error page.
Thanks for your comment Bill. The reason they say lift the camshafts out level is so you don't crack or break one. They are very brittle and when loosening their bolts loosen a little at a time so that the cams come up even, you don't want any stress on them or you can easily break one.
The name of the tool in the video is "Pin Pliers" I will put a link in the description to a set on Amazon.
@@Engineerboy100 Thank you, Clint. I can see you are a good man, and appreciate your helpfulness.
Hello again Clint. I received the tool you suggested, the "Pin Pliers." Now, I am using those pliers, to try to turn the sub-gear clockwise while holding a cresent wrench on the flats of the camshaft and putting my maximum force into the effort, but just cannot get the sub-gear to turn any, so cannot line up the hole to insert the bolt to pull the two gears together on the intake camshaft. The repair manual states that this bolt MUST be installed before attempting to remove the camshaft.
Remember, I am attempting to remove the camshafts from a re-manufactured head for my 7AFE engine, so the two cam sprockets (gears) are meshed and the camshafts are still bolted in with 4 caps each. Only the intake number 1 cap has been removed, nothing else. Given that assembly, should the sub-gear be able to turn the slight amount needed to line up the holes? Is it just that I am not applying enough torque? Maybe a bigger, stronger man could do it?
BTW: the 1994 Celica ST manual specifies the intake camshaft for this 7AFE requires a 6 mm 1.0 bolt of from 15 to 20 mm length. You said yours was a 10 mm bolt. The threaded gear is the thicker one, so I think I would have to screw the bolt from the other side than you showed in your video, i.e., the sub-gear side, to pull the two gears together so the shaft can be eased out. @@Engineerboy100
@@billcowhig5739 If the gears are still engaged, you don't need the tool, the hole is already lined up. You only need the tool if you take the cams out and forget to put the screw in before removing them.
You. Are. My. Saving! The first part with the spring loaded gear was what I was searching for, over 4 hours.. Thank you sir!!
Thank you for the comment Richard, glad I could help. Happy new year!
Clint Hightower today, I have finished the installation of the camshafts on my sisters Cuore. As feedback: this video does also applies on that 3 cilinder EJ-VE engine. Camshaft lobe facing to the front of the verhicle (with engine at timing positions), timing marks on the gearlinkage and the springloaded gear with a set screw (Daihatsu is M5~8mm though). Again, many thanks and a happy and great newyear!! Hero
Sweet! That is awesome, thanks for the feedback.
This is very detailed very well explained. Thank you for helping us!!
What a great video! I watched mainly to confirm the bottom timing marks before I take the t-belt off and this shows everything so clearly. One thing I don't understand is why the Haynes manual goes through a whole rigamarole involving the #1 cylinder based on the position of the distributor rotor, which seems totally unnecessary since these marks show everything and you're in there looking at them anyway. Why mess around with the distributor if you don't need to?
Enjoyed your vid, thanks
Thanks for watching John, and thank you for your comment.
@@Engineerboy100 No worries I have a mechanical business in Australia so these things come in handy, thanks again
Thank you for this!....you are an excellent teacher!
God Bless you Clint! Thank you brother. Great video.
Thank you kindly
Hello Mr. Hightower. Can you do a video on replacing the camshaft seal on the 93-97 1.8 7afe engine. You seem to take the most time explaining things in detail. My 96 Corolla dx has 363k and still going strong. Thanks.
Very clean instructions, professionalism all the way.
Thanks man. This helped me so much after replacing my head gasket
Thank you for your comment, I absolutely love helping people :)
Finally a through explanation I really appreciate this maybe I can get the car to start now thanks buddy for taking the time, I knew the lobes needs to point somewhere specific
Did you succeed?
@@steveakendo8579 Yep ;)
hey sir thank you for all the explanations...but could you do me one favour...is the stock camshaft sprocket really adjustable...if it could can you show me how to adjust please...my car is very slow to gain speed even my timing engine is correct.
Yes, the sprocket is supposed to be sprung, see this video ruclips.net/video/VhGWPQTQDOU/видео.html
Thank you. i needed this info. I was replacing the waterpump and i pressed against the timingbelt and that broke the timing belt. Thanks again.
You are welcome, glad it helped you, thank you for your comment.
Love this video, thats for sharing, you are an excellant teacher, slow and precise for old timers like me:)
Thanksss boss's..this verry clear...to understand....
Does the two cam lobes is at same angle or the intake cam lobe will be facing higher / upper?
The lobes will not be exactly at the same angle but the lobe angle is only to be used as a reference. Go by the timing marks for the correct timing.
@@Engineerboy100 thank you I got it right. But I still have issue. Can I get your facebook account so I can message the video
@@Engineerboy100 I have a ticking sound and it seems near the intake manifold. I know injectors make some ticking noise but on what I am hearing it is a bit louder and it is coming near the intake manifold.
This video has been extremely helpful. Thank you.
Question; On my 7AFE 1.8L with 140K turns out the Camshaft bolt backed out 1/2 in and the Knock Pin dropped out. I did find it. It must have slapped against the wheel groove widening it by a few mm. About 3to4mm of slap. So wil replace the Top Timing Wheel for sure. Do you think I would need to replace the Exhaust Cam as well? Im looking for a new knock pin but I believe it's sold with the Cam only.
There's no way for me to be able to know if the exhaust camshaft needs to be replaced or not. One rule of thumb I have found to be true with camshaft damage, they don't usually "bend" they are fairly hard and a little bit brittle. usually camshaft damage is they either crack or they don't.
Thanks,really explained alot
You are good at explaining, l understand you more in this video than the explicasion in the career of automotive technician, greetings from mexico
Thank you Mario, I'm glad you liked it. I explain things in my book the same way, you should down load it here for free or you can purchase a hard copy on Amazon. Have a great day!
Mario antonio Olvera hernandez
With your set screw in place, how did you get the sub gear lined up with the main exhaust cam gear? trying to realign mine on my 2fzre 2.4L
you need a cam gear alignment tool, something like this: www.amazon.com/EWK-Universal-Camshaft-Sprocket-Holding/dp/B00VFPOF1E
Is this cam shaft installation the same for the 4AGE Blacktop? At TDC, shouldn’t the cam lobes over No. 1 cylinder be pointing toward each other, not pointing towards the front of the car like what you have shown in this video?
I believe so. 7afe and 4age are very similar. I think the heads are the same but the bock displacement is 1.8 and 1.6 litre respactively
So far the best explanation i have seen
Thank you.
Thank you :)
Hi sir,i have a cuestion...the book for toyota four runner use the two points dot marks to do the head gasket replacement.what to do if the dot marks are aligned but the little hole of the cams is like 5 o clock instead at twelve o clock. I hope you understand my broken English.
Just in case you answer my cuestion my car is a 4 runner 99
It means you are probably 180 degrees out of time. You are trying to time the engine on the exhaust stroke and it needs to be on the compression stroke. Turn the engine over one more time manually, by hand and try it again and the marks should align. and yes your English is fine.
Thanks for replied.im doing a head gasket job, the timing belt is not in place,it's posible to rotate the camshaft using the bolt and rotating it to the right? Or it's better to dissamble and start over again.
Enjoyed the way you explained this tricky procedure. Is the 5s-fe time up in a similar way? Cheers
I'm not sure about the 5afe. But the 4afe and 7afe are the same. I have done both.
I have a Nissan Micra 2005 cr14 engine. Can you assist with setting up the camshaft timing without removing the timig cover cover.
How do I know if I’m 1 belt tooth forward or back, off?
When I align the camshaft holes with the camshaft pulley hole and crank to 0 my belt is in 1/2 tooth of the belt.
I’m not sure if I should move either the camshaft or crankshaft forwards or backwards to align with the belt tooth…
Any help appreciated thank you for the video as well!
You have to make sure the timing marks are aligned first, then you align the belt with the cam sprocket and the crank, not the other way around.
@@Engineerboy100 the dots on the cam were aligned and the crank was aligned at tdc, just it aligned at a half tooth so either I had to go a bit back or a bit forwards to fit the sprocket groove.
Ideally I think it’s on time now just the extra 1/2 - 1 second of starting. Before I’d turn the key and it would fire almost instantly, so I do believe either I’m off a bit or the parts are new and it’s tighter. I think more so I’m off a bit, first time doing a timing belt.
Good job! Only thing I would add it that a lot of corollas have two holes in the camshaft gear. Line the hole marked A, not the hole marked K
Good point. Thanks Mt Man :)
Miss that step of service bolt and now back assembling camshafts do I have to put the service bolt? Before assembly?
The service bolt is for holding the spring tension of the sprung sprocket so you can get the gears to mesh. If you assemble the engine without the spring tension of the cam gears, they will rattle quite noisily.
Clint Hightower thank you sir GOD BLESS YOU AND FAMILY
You are AWESOME 😎 thanks 👍🏻
is this the same with 4af engine?
Yes, Same as 5afe,.
@@Engineerboy100 wow, thanks!
How can I remove the bottom timing belt sprocket? I tried prying a little with screw driver. Not much area to pry.
I was planning to replace the seal behind there.
You may need to use a puller.
Smart trick on tightening the tension with spring on so don’t have to fight with it later
If I don't have the bolt can I use a smaller bolt to fit through the holes ? Does it have to be threaded in ?
It's best to use the correct size bolt for the best results and the most accurate re-alignment of the split gear teeth.
Very helpful, Thanks man.
Congratulations good instructions, thanks
what is the cam shaft retanier torque specs? on this model? thanks in advance and happy new year...Great video
Here is a free copy of my book. Check out the Trouble Shooting Chapter especially, download pdf from my Dropbox. www.dropbox.com/s/mcwpv0rb7lun038/0%20Entire%20book%20with%20covers%20and%20QRC%20for%20eBay.pdf?dl=0
tank u very much sir
Man i sure appreciate u and this video. Lol.. Im doing head work on this same engine. I thought it was a sohc to i took the valve cover off and it was a dohc. Man u save me. Lol. Greatly appreciate it..
i have a 1mzfe am putting back together. the spring gear is what im confused about. the 1mzfe doesnt have a set screw, so where should the spring gear line up? I can make it so you can partially see through the hole or i can turn it some and make it so i cant.
I'm not sure what the thread pitch is on the 1MZFE, but a common bolt is the typical 10mm, test the threads with a few bolts to figure out what the thread pitch is or you can cheat and look in the shop manual for your camry or whatever your 1MZFE is in and it should tell you. or you could call the dealer and ask, sometimes they are helpful.
Thanks for the quick response! i have both heads off and both dont have set screws on either of the the given cams. So you are saying its suppose to have set scerws there? not sure if im the first one to rebuild this but it was running fine without the set screws whole time ive had the vehicle.
i just looked at it this am. the cam with the spring gear can be moved to 3 diffent teeth, if that makes sense. probably the middle one is the right one?
I replace my Toyota corolla 1.6 2000 model cylinder head gasket, set timing and everything but the engine crank but don't start. I replace ignition coil, spark plug wires.
Check timing and fuel pressure.
Chek spring loded camshaft and timing
Does this work for 5afe engine also? And does the hole on the sprocket have to be in line with the lobes facing the front of the car?
I'm not sure about 5afe but it works for 7afe and 4afe. check out this page, it might help. motor-car.net/toyota-engines/item/14611-toyota-5a-engine
@@Engineerboy100 i guess it does
The engines are similar
Informative and to the point
Hey I’m working on 2002 tundra 3.4 liter v6 5VZ. Been stuck for bout 4months . Trying figure out if I got cam gears set rite if the timing is rite . I’ve been watching your video over over . I’m not quite sure if my timing is rite . Oil pan is still off I could send picture video if it would help you to better understand .
I’m trying do same thing to the motor like your video same concept . I’m just thrown off by . Your corolla had two cam gears which in my case I have two sets . And that’s where I’m assuming Why I’m not able to understand clearly.
So just like to thank you . All your videos are useful easy to comprehend. Or I’m looking at this particular video and watching it in a wrong way?
You should get a shop manual for your exact model vehicle, and follow the procedure for setting the timing, each vehicle can be a little different.
Clint Hightower yeah I purchase one from advanced Haynes manual . I wanted to get the dealership manual price for the knowledge is reasonable n fair for the info it contains . Not able to afford it yet. But hey thank you . Least you took the time to reply with honest advice .
Hola tío mira aunque no te entiendo ni pío osea nada entiendo tu explicación física gracias buen vídeo
Hello. I'm wondering if this engine uses a camshaft sensor. If yes, Where is located?? Thanks
The 1994 doesn't have a separate CPS, only OBD2 (95.5-96+) 4afe/7afe have a crank position sensor for determining cylinder misfire. It's part of OBD2 emissions self diagnostics. 94's rely on a cam position sensor that is inside the distributor.
Clint Hightower .. "Thank you Sir".... Useful information....
whats the torque setting for the cam bolt on the 3rz-fe my year truck is a 2000
Not sure, but I would never trust an answer to that kind of question over the internet. That is a look it up in the shop manual kind of question.
clear instructions awesome camera action great all round thanks heaps mate
Thank you Robert, I appreciate the comment.
Does the timing affect the vehicle's power?
Yes! The timing is everything in an engine.
Thanks Clint!
You're welcome Samuel ;)
Hi there what is the name of that tool and where can I purchase it? Please let me know thanks
It is a pin spanner wrench, there are many configurations. Hope this helps.
after rebuild setting camshafts and timing as it should be I got a ticking sound in the head of the engine, you know what could be my problem?
Yes. That ticking sound is your lifters. Toyota's have solid lifters and can only be adjusted by replacing shims. the thickness of the shims establish the distance of clearance between the camshaft lobes and the lifter "discs" there are specs the manual and you have to measure the clearance with a feeler guage ... it is not a beginner project .... read up on this more before attempting.
TurboFo_Oil_Changer Porsche_Light_Saver thx for quick reply, you know where I could find the manual online as I bought the car and the previous owner did not have the manual
www.ebay.com/itm/1993-Toyota-Corolla-Shop-Service-Repair-Manual-Geo-Prizm-1-6L-1-8L-/192017083116?hash=item2cb51c2aec:g:eEAAAOSw4shX8teP&vxp=mtr
that's a great job and Good work.
Thank you Gift.
Great video Clint !!! enjoyed you explaining how to install !!!! Keep up the good work .. I just subscribed
Thanks Frank :)
Tienes algún video de... Cómo cambiar el retén del árbol de levas del Toyota 4A o 7A??, gracias.
how do you connect leads with the coils of a toyota corolla 4E engine
Excellent video! Thanks for posting.
Your information is the best, thankyou sir
Thank you so much Magnum, I'm always trying to improve. Hopefully my future videos will be even better.
Bueno Días maestro me puede decir cuál es el número de la retenedora del eje de leva
No lo sé, lo siento mucho.
Is this the same for a 4EFE engine
No, they are not the same. there are similarities, but they are definitely not the same.
Hi Clint my intake cam has no set bolt
just get a small 10 mm bolt, it is a standard size not sure of the thread pitch.
Me is a mechanic I like this thing
Man
You are the best teacher
Thanks
Thank you Fabiola, I'm glad you liked it :)
Fabiola Garcia M
Ce que je veux savoir est que si le cache poulie d'en bas est cassé comment on procéde ???
This can also be applied to the 4aFe?
Yes, the head is the same, the 4afe only has a different size engine block, 1.6 vs 1.8. I have swapped heads between them.
I love your lessons
Very good informative video. Thank you!
Thank you Jason! I appreciate the kind words, keeps me goin ;)
How much force does it take to re-spring the scissor gear?
Very little like 20 fb-lbs ;)
Clint Hightower I just replaced the cylinder head on my tacoma 3rz and could not figure out why it was making noise at idle and also slightly misfiring. I guess the backlash was just enough for a slight misfire, Thanks to your video it runs 100% now thanks a ton happy new year ✨
Thank you so much, I will subscribe.
What a great video
Thankx 4 the time.sir
Thank you, I love learning from others and sharing what I know.
What's the torqued of the camshaft?
You should get all of your torque spec . information from your shop manual, never trust someone telling a torque value on an importing internal engine component. If that is how you get your torque information, you should not be building engines.
Easy to understand instruction........
Thank you man, saved me alotta time....
Awesome, thanks for your comment, glad I could help :)
Is this timing the same for celica sti?
Not sure about the sti, but this engine did come out of a Celica.
@@Engineerboy100 thank you
Hello. Can this go for a Toyota Prado petrol?
I do not know, but I don't think so, each car is usually different. Sorry.
Is this the same for the 1999 Camry 2.2
No, two different engines.
Is this the same as a 4afe?
No. 7afe is 1.8L engine 4afe is 1.6L engine. The share the same cylinder head.
Why cam shafts make louder when engine are on
Lifters need to be shim adjusted.
best teacher
Thank you :)
Very nice video
Thanks 43 :)
Thanks very good explanation
Thanks
Don't forget to remove the bolt from the sprocket :)
Good advice! :)
Very informative video
obrigado meu amigo estou montando um cabeçote agora você tirou minha duvida
Buena suerte y bueno para usted. Que te diviertas
Thank you juses
Thank you!!
Thank you so mush
You are welcome, I'm glad you liked it, more to come :)
Power full
❤
What's the name of that tool?
Camshaft sprocket holding tool.
www.ebay.com/itm/Honda-Toyota-Universal-Camshaft-Injection-Pump-Sprocket-Holder-Holding-Tool-/172142327886?hash=item28147b784e:g:0OQAAOSwHgVW73Oa
The first one, 1:00
very cler instruction musterd
Nice lessons but more dark