You made my day mate. I checked the brushes, notice they were short arses, pulled them out a tad ,put back together and wackydoo all worked as it should. Thanks a bunch 🙂
I had the 3E error on my Samsung washing machine and the filter was pretty clogged, so I cleaned it. I had to put a pizza pan to catch the water, and empty it about 10 times, to empty out all the water in the machine. I cleaned out the filter and put it back, and it still has the 1st light blinking on and off. I no longer have the 3E error, but the machine goes for about 2 minutes and then stops, and just sets there for about 10 minutes and then goes a little bit more, like another few minutes, and then stops again. The 1st light, like perhaps a water filling light, is blinking. Any ideas? Thanks.
I have a ecobubble Samsung washing machine. My machine puts a code 3E motor error. Following your instructions I searched for brushes to change, has none. BUT I took out the two pumps and one of them was filled with papers, so I unblocked an cleaned it. After that it keeps putting out the error BUT only if I put a temperaturemore than 30 degrees Celsius. What now?
Yep done that, done that, done that, done that. Nothing new here. A thousand Vids with this stuff. Done the hall sensor test. Somebody show us how to fix the PCB or make Samsung replace them for free!
Hello we have a Samsung washing machine model number wf600b0bkwq in this motor not have a carbon brushes what we have to do tell me that3E showing error code in the display Tq...
Hi this one has an invertor motor. Usually with these it’s the contacts on the main board that have come loose, the soldered connection is broken. Unfortunately I haven’t done a video on one yet but there are plenty on RUclips at the moment
Thanks for the tip about accessing the motor from the base of the machine, saw another video accessing the motor from the rear and taking the motor out, a right pain. Fitted the two carbon motor brushes from the base of the machine, no need to remove the motor or the drive belt.👍👍Samsung eco bubble lives again, all for a pair of £16 carbon motor brushes, I hope the brushes last .🤣 thanks again. 👍👍👍
Thanks 👍 brother, i have the same machine with 3e error and I opened it up and the bottom brush is only about 5mm long, ordered some new ones online hopefully they get here before we run out of clean clothes cheers!
Awesome video dude. We picked the machine up off the side of the road, Googled the error code and thanks to your video got the old girl humming like a bird. Swapped the top and bottom brushes over and an off to find new brushes tomorrow. So for the cost of the brushes we have a new second hand washing machine that retails new for about 900 Australian dollars
Legend, thanks for video. Checked the brushes and the carbon dust had clogged the aperture. The machine is running again, but I'm ordering new ones now....❤
I called samsung and they wanted to change the hole motherboard, i watched the video and got new brushes and installed them and it worked, thank you man ♥️
Brother. Thank You so Much. Our washing machine stopped spinning and after running it in diagnostic mode it came up with E3 error. Now I'm not a master engineering but I can tinker with some screws :) so I ordered new brushes and replaced them as instructed and everything works fine. God Bless you My Friend.
Thank you so much - very good tutorial. Spares cost me NZ$67 (mission to find them), and it took me 10 minutes to get our 8 year old machine up and going again.
Thank you, it was the brushes. First one looked ok but other was badly worn, I order a pair of Amazon last night and it’s back up and running in less than 24hrs Thanks Again
looking at them brushes look fine so if no good why put whats left of them in the bin .never ever seen that lenth needing to be replaced ive fixed washer all my life
Hello mate - great video. Did as instructed and she worked a treat. Saved me from having to buy a new one. Samsung WF1752WPC - showed a E3 error. Replacement brush cost me AUD$16 on eBday. Took less then 5min. Hardest part was flipped it over. I’ve done a drum clean and handed it over to the mrs to clear up the back log of unwashed cloths. Great video - keep up the good work. Cheers
Hi mate,had an engineer out,who eventually changed the complete motor.Still went,and continues to go to E3. It still works ,but still goes to E3 four out of every five washes,driving me insane.The engineer says the fault must be with the pcb,and advises to buy a new machine.Sounds drastic when everything else works ok
Fixed. Wouldn’t have known about this without your video. Tricky to find the carbon brushes for my model but I bought similar looking ones then popped the casing and swapped the carbon. Pile of dirty clothes being washed right now plus I’ve cleaned the filter and waste pipe! Thanks!
Hi sorry about that will get it sorted soon. Type on eBay carbon brushes for Samsung washing machine. Type in your washer model number as well this will help
Thank you. This video fixed my issue. Just a quick question, i am getting a low sound when the machine is running. Kind of noise that we get when we rotate the drum manually. Is that normal? or should i check it out again on something. Mine is wf8750lsw
Hi - great help - just wondering - I am getting a noise (sounds like from the pump you were pointing out) before 3E code appears. It looks clear but is there any possibility of stuff having got into the pump itself?? If so, what can I do??
hi thanks for reaching out. You will need to grab a torch open the filter cap and put the washer on a spin cycle. During that cycle have a look down there where you took the filter cap off to see if the pump is spinning freely. If nothing is there a noisy pump that still spins indicates you need a new one as its not spinning fast enough to drain the water in the allocated time.
@@askmrwashywashy Thanks for your prompt reply. I did that and whilst there was a little noise, the actual main drum itself didn't even spin, so I will investigate the carbon brushes further with the help of your video.
@@askmrwashywashy Just wondering - How long would you normally expect these brushes to last in normal circumstances?? (just 2 of us!) - I am sure the machine is only ~5 years old.
@@normanmcauley6353 Depends on how often you wash in a week. The more often you wash the faster they wear. 5 Years would be about the time you need to replace the brushes. You would want to replace them possible at 3-4 years to avoid them wearing down to the wires and then possibly burning out your main board
hi check the motor where the brushes sit, might be too much carbon buildup. Also make sure you have replugged brushes back in. Apart from the the main board might have a problem
My brushes seem good (about 4 inch. Swapped them anyway). Filter clear. Still when I try a test cycle it makes a quick drain noise and then flashes up 3E. Can't seem to see any blockages
Thank you very much! The carbon brushes were the problem so an easy $70 fix instead of having to get a new machine straight after the Christmas shopping. Thank you.
Hi great video and I have replaced the carbon brushes and the 3E error has gone away and the drum spins but it does not spin at full speed leaving the clothes too damp. Would you know the reason for this?
Thanks , glad you could sort out that spinning issue. Couple of things might be causing the clothes to stay damp. The drain pump might be a bit old, so its not pumping out water fast enough. Other thing is how much is your wash load ? Optimum load would be about halfway up the door. What Rpm is it spinning at 1200 or 800 ?
Thanks for the video, the top brush had heaps left by the bottom one was very short but I gave it a good yank to extend it out a bit, hopefully it lasts until the new brushes arrive so I can cross thread all the screws again.
You made my day mate. I checked the brushes, notice they were short arses, pulled them out a tad ,put back together and wackydoo all worked as it should. Thanks a bunch 🙂
Welcome glad it helped ya
I had the 3E error on my Samsung washing machine and the filter was pretty clogged, so I cleaned it. I had to put a pizza pan to catch the water, and empty it about 10 times, to empty out all the water in the machine. I cleaned out the filter and put it back, and it still has the 1st light blinking on and off. I no longer have the 3E error, but the machine goes for about 2 minutes and then stops, and just sets there for about 10 minutes and then goes a little bit more, like another few minutes, and then stops again. The 1st light, like perhaps a water filling light, is blinking. Any ideas? Thanks.
I just cleaned the drum, and it seems to be working, and draining very well.
I have a ecobubble Samsung washing machine. My machine puts a code 3E motor error. Following your instructions I searched for brushes to change, has none. BUT I took out the two pumps and one of them was filled with papers, so I unblocked an cleaned it. After that it keeps putting out the error BUT only if I put a temperaturemore than 30 degrees Celsius. What now?
Currently three minutes in , and I love this video already.
Comments sold me.
You the man, had 3e error, pulled off brushes, one was well short, swapped them over and boom works. Ordered new ones for £7. THANKS ALOT
welcome glad it worked.
Have link to where you bought them? Thanks
Thanx Kyle. After seeing your comment I swapped the top and bottom brushes over and away she went.
Is swapping them over a good idea?
Yep done that, done that, done that, done that. Nothing new here. A thousand Vids with this stuff. Done the hall sensor test. Somebody show us how to fix the PCB or make Samsung replace them for free!
Thank you Mr Washy Washy, will be turning it on its side tomorrow...🙂
Oh mate! Thank you so much, this video was really helpful! God bless
welcome glad it helped
Hello we have a Samsung washing machine model number wf600b0bkwq in this motor not have a carbon brushes what we have to do tell me that3E showing error code in the display Tq...
Hi this one has an invertor motor. Usually with these it’s the contacts on the main board that have come loose, the soldered connection is broken. Unfortunately I haven’t done a video on one yet but there are plenty on RUclips at the moment
Absolutely spot on mate. Managed to wiggle a little more life out of mine until a replacement arrives. Thanks so much!
welcome glad it helped you
NO!! First thing is to unplug the machine!!
Yes sorry forgot to mention that
Thanks for the tip about accessing the motor from the base of the machine, saw another video accessing the motor from the rear and taking the motor out, a right pain. Fitted the two carbon motor brushes from the base of the machine, no need to remove the motor or the drive belt.👍👍Samsung eco bubble lives again, all for a pair of £16 carbon motor brushes, I hope the brushes last .🤣 thanks again. 👍👍👍
welcome glad it helped
Thanks 👍 brother, i have the same machine with 3e error and I opened it up and the bottom brush is only about 5mm long, ordered some new ones online hopefully they get here before we run out of clean clothes cheers!
E3 lavadora mastertech
Awesome video dude. We picked the machine up off the side of the road, Googled the error code and thanks to your video got the old girl humming like a bird. Swapped the top and bottom brushes over and an off to find new brushes tomorrow. So for the cost of the brushes we have a new second hand washing machine that retails new for about 900 Australian dollars
So I have this model and the motor isn't on the same side. Could it be on the upper part? I have Samsung Model WF3S8AAWXAA 02
Followed your video, found the problem, replaced the parts and it is running like new. Thanks a lot 🎉
I have a way different model of motor, I've got a wf42h5000aw/a2 how would i go about fixing an 3e error on mine
Yours has a computer that controls the motor. You would need to replace that and the motor
Thanks a lot
It really halp🎉🎉🎉🎉
Can you send the carbon model the link in the movie don’t work
Legend, thanks for video.
Checked the brushes and the carbon dust had clogged the aperture.
The machine is running again, but I'm ordering new ones now....❤
❤
Thank you so much. Blessings
i was hoping you had a solution for me but my washer has a stator motor rotor or whatever in the back. No carbon brushes on wf419aaw/xaa
I called samsung and they wanted to change the hole motherboard, i watched the video and got new brushes and installed them and it worked, thank you man ♥️
Brother. Thank You so Much. Our washing machine stopped spinning and after running it in diagnostic mode it came up with E3 error. Now I'm not a master engineering but I can tinker with some screws :) so I ordered new brushes and replaced them as instructed and everything works fine. God Bless you My Friend.
Welcome glad this worked out for you
Thank you so much - very good tutorial. Spares cost me NZ$67 (mission to find them), and it took me 10 minutes to get our 8 year old machine up and going again.
Welcome. Awesome I’m so glad you could fix it
Thank you, it was the brushes. First one looked ok but other was badly worn, I order a pair of Amazon last night and it’s back up and running in less than 24hrs Thanks Again
I have a 3E coming up my washer, the drum wont spin and makes an awful noise trying to, the drum also seems loose and im not sure what to do
my washer model is : WF431ABP/XAA 04, DOES THIS MODEL IS AS SAME AS YOUR MODEL? CAN i ALSO CHANGE THE CARBON BRUSHES TO SOLVE THIS PROBLEMS? THANKS!
looking at them brushes look fine so if no good why put whats left of them in the bin .never ever seen that lenth needing to be replaced ive fixed washer all my life
I have a similar machine but i have recently got an upside down f e2 error code help please
Salve non è più facile togliere il motore per la sostituzione delle spazzole
Thank you so much for this knowledge! saved me big bucks 😇
Hello mate - great video. Did as instructed and she worked a treat.
Saved me from having to buy a new one.
Samsung WF1752WPC - showed a E3 error. Replacement brush cost me AUD$16 on eBday. Took less then 5min. Hardest part was flipped it over.
I’ve done a drum clean and handed it over to the mrs to clear up the back log of unwashed cloths. Great video - keep up the good work. Cheers
awesome glad to hear you sorted it out.
Hi
Hi mate,had an engineer out,who eventually changed the complete motor.Still went,and continues to go to E3. It still works ,but still goes to E3 four out of every five washes,driving me insane.The engineer says the fault must be with the pcb,and advises to buy a new machine.Sounds drastic when everything else works ok
Hi yeah it’s a bit weird would’ve changed the board and not the motor in that case. Seems like a waste of a good motor and money now.
why did it take you 7 mins to start unscrewing?
Watched and repair mine as well thank you so much! Saved a fortune on your video 🎉
Fixed. Wouldn’t have known about this without your video. Tricky to find the carbon brushes for my model but I bought similar looking ones then popped the casing and swapped the carbon. Pile of dirty clothes being washed right now plus I’ve cleaned the filter and waste pipe!
Thanks!
awesome im so glad you fixed it. Well done for working it out
@Alistair young mine one is also inverter and in warranty but they don’t tell me that this is the motor problem so they can ask for bills
i am belgian based where can i get these parts
Hi can i use the method for samsung wf80f5e0w2w
Thank you
If it has a brushed motor yes
I have wd106u4sagd samsung digital inverter with 3E error. Any thought how to resolve this? Thanks for the help.
Hi usually with inverter type ones like yours you need a new board.
the ebay link is no longer working, can I please the spec of the brushes to source them myself? thanks a lot
Hi sorry about that will get it sorted soon. Type on eBay carbon brushes for Samsung washing machine. Type in your washer model number as well this will help
Thanks brother… I fixed it
Thank you so much for sharing this video. You have helped me fix my washing machine! Thank you 😊
Glad I could help!
Thank you. This video fixed my issue. Just a quick question, i am getting a low sound when the machine is running. Kind of noise that we get when we rotate the drum manually. Is that normal? or should i check it out again on something. Mine is wf8750lsw
Welcome. Might be the new brushes bedding in. Should disappear after a few washes
Where can I get the carbon brush
thank you! it was the brushes for me too
Like K Jones said, Thanks for this video, really saved me. Much appreciated
Glad it helped
Model WF80F5E5P4W. Does this fix work with my 3E problem?
hi your one is brushless motor so no. it needs new motor controller pcb
@@askmrwashywashy Thanks for the help! I can’t find info on model # wf393btpawr/a1. Thanks
Why is there no sound
Great video man. Where is the link to buy the new brushes? Thanks
thanks glad you found some value in it. Link should be in description
Hi - great help - just wondering - I am getting a noise (sounds like from the pump you were pointing out) before 3E code appears. It looks clear but is there any possibility of stuff having got into the pump itself?? If so, what can I do??
hi thanks for reaching out. You will need to grab a torch open the filter cap and put the washer on a spin cycle. During that cycle have a look down there where you took the filter cap off to see if the pump is spinning freely. If nothing is there a noisy pump that still spins indicates you need a new one as its not spinning fast enough to drain the water in the allocated time.
@@askmrwashywashy Thanks for your prompt reply. I did that and whilst there was a little noise, the actual main drum itself didn't even spin, so I will investigate the carbon brushes further with the help of your video.
@@normanmcauley6353 welcome. I’d say check the brushes and take it from there. Let me know how you go
@@askmrwashywashy Just wondering - How long would you normally expect these brushes to last in normal circumstances?? (just 2 of us!) - I am sure the machine is only ~5 years old.
@@normanmcauley6353 Depends on how often you wash in a week. The more often you wash the faster they wear. 5 Years would be about the time you need to replace the brushes. You would want to replace them possible at 3-4 years to avoid them wearing down to the wires and then possibly burning out your main board
Hi, in my case the brush look fine, what might be the issue?
hi check the motor where the brushes sit, might be too much carbon buildup. Also make sure you have replugged brushes back in. Apart from the the main board might have a problem
@@askmrwashywashy Hi, thanks for replying, i checked the motor separately and it is working it seems either issue with PCB or Tachometer.
@@flokyshah5877 yeah might be pcb or tachometer
Hi, our motor looks different everything is incased and I can't locate the brushes. Thoughts?
Ok....it's a brushless motor, so if the filters clean then it's a computer problem?
@@lanceking9288 hi what’s your model number ?
@@askmrwashywashy
WF1104XAC/XSA 04
Y3UF53AG700133Z
....these were the numbers I pulled off the door
@@lanceking9288 thanks for that. Can you turn the inner drum by hand ?
@@askmrwashywashy yep I can
Is it inverter??
It’s direct drive
Is this the same as e3 error?
E3 is for water overflow. Different issue
My brushes seem good (about 4 inch. Swapped them anyway). Filter clear. Still when I try a test cycle it makes a quick drain noise and then flashes up 3E. Can't seem to see any blockages
Thank you very much! The carbon brushes were the problem so an easy $70 fix instead of having to get a new machine straight after the Christmas shopping. Thank you.
Hi great video and I have replaced the carbon brushes and the 3E error has gone away and the drum spins but it does not spin at full speed leaving the clothes too damp. Would you know the reason for this?
Thanks , glad you could sort out that spinning issue. Couple of things might be causing the clothes to stay damp. The drain pump might be a bit old, so its not pumping out water fast enough. Other thing is how much is your wash load ? Optimum load would be about halfway up the door. What Rpm is it spinning at 1200 or 800 ?
@Tech Tech can you turn the drum barrel by hand ?
@Tech Tech Double check your wiring connections. If that doesn't work the board might be blown and you need two replace it
@Tech Techwow I’m so glad you were able to sort it out. I’ve learnt something new today 👍good on ya
Hi mate, what's the model of the washing machine you working on the video?
Hi mate , its the WF1752WPC. Which one is yours ?
@@askmrwashywashy WF1752WPW
@@jericvalle2262 will work for your model as well
@@askmrwashywashy what bout model wf219anw/Xaa 01
Thanks for the video, the top brush had heaps left by the bottom one was very short but I gave it a good yank to extend it out a bit, hopefully it lasts until the new brushes arrive so I can cross thread all the screws again.
I have the same error 3E2 , model number: WD10J8420GW ,
Washing machine and dryer ,
What is the problem please?
Hi. I’ve replaced Carbon brushes but 3E still remain..why?
Solved! Thanks
@@ColeTropea Oh great what did you end up doing ?
@@askmrwashywashy After replacing the brushes I forgot to insert the cable 😅 so i did it and it worked.
@@ColeTropea haha yeah I do that sometimes. Glad you worked it out
Where can i get the carbón brushes?
Really useful info but man edit your videos to reduce the length. I basically had to skip the majority of the video to get to the useful content
Hi thanks for the feedback I’ve shortened them since then.
You talk too much....
Than you for the feedback will improve in future videos
What a load of shit