This is Ash from HealMyTech & I need your help. I recently suffered a STROKE (end July 2021) which has left me disabled for now (temporarily?), which may have been caused by the VACCINE ASTRA ZENECA. The videos were uploaded on my channel end August 2021. I have set up a GoFundMe, any donations are welcome. gofund.me/ccb57a48 Here is also my paypal link paypal.me/healmytech The links are also in the description with other ways to donate.
Dude! You're a life savior! I pulled those pins accidentally and I was trying to find a vid that helps. They weren't as helpful as yours. My pc is working you just got a new sub!
Those pins are a pain in the ass to put in when your gpu is installed....then if you bring your pc to a friends house there is always that chance some of them will pop off.
Dude, I can’t thank you enough. I was literally panicking because I accidentally unplugged the pins. My computer turned on and works like a charm! You earned a like and subscribe, man, your a lifesaver.
This saved me! I just got a new motherboard and had that moment where I had everything plugged in, proud of myself, then pressed the power switch and... nothing. Luckily for me, this video exists. Thanks a ton!
got same problem, but i"m pretty certain that i have plugged those wires into wrong place. i have them plugged to JFP2 since that has not worked i will try to switch. also first time the power button was glowing red. honestly this so confusing when my motherboard manual MSI mortar is not explaining it very well. excellent video thanks for uploading it i would be stuck if not for a video on this that is not years old.
pls help me, i have tried everything, i plugged everyting in the right spot on the motherboard while outside the case and it turned on, but when i put the motherboard back in the case and plugged everything in it did not turn on, one time id did turn on while i had the power cable for the motherboard plugged in and the power for cpu plugged in while the motherboard was inside the case but when i plugged in the rest of the cables like usb, audio and other and felt like i was done the power did not turn on... (ive installed all the risers)
This just saved me so much money. I worked on my first PC build today for 6 hours straight and was so proud until I pressed the power button and nothing happened. I already gave up, was ready to go to bed and planned to take my PC to a shop tmr to get it fixed. Then I watched this vid while already in bed, jumped up, tried again and voilà. Thank you so much! 🙏🏻😆
YOU JUST SAVED ME MULTIPLE HOURS OF STRESSING! I had just built my sons first custom gaming PC and we tried to turn it on, but nothing happened. We were trying over and over to find a problem, and right before we were about to give up, we found your video. After watching it, it instantly fixed our problem. We cannot thank you enough!
Q - Which of the front panel connectors wire are necessary to at least turn your computer on? A - The answer is none of them are required. After installing the CPU, and RAM and connecting the PSU cables, you need only short the two Power Switch pins on the front panel block to start the PC. This can be done carefully with a medium blade screwdriver, just touch both of the Power Switch pins with the screwdriver, As for the situation with the 3-pin Power LED connector.... Case specification several years ago. One of the changes was going from a 3-pin to a 2-pin connector for the front panel Power LED. This is why many cases today have a split connector for the + and - Power LED like you show in your video to accommodate older motherboards with either the 2 or 3-pin connector. In the case of your MSI board, it has both 2 and 3 pin connectors for the power led to accommodate just about any computer cas you might be trying to use. On your MSI board, the 3-pin connector is labeled PWR_LED. The 2-pin connector is the one labeled [+MSG-] your motherboard's front panel header. They are labeling it a MSG connector because in addition to providing a steady power-on light. it will also cause the LED to blink in sleep mode and provide other 'messages', using a pattern of blinks to show stuff like P.O.S.T. status or errors. Good luck!
Thank you so much, your the only RUclipsr I could find who showed the proper camera angle to get them in, everyone else was either having a seizure with their camera or just not showing the entire socket, I was starting to think I wouldn't find a good tutorial, but here it is.... Liking and subscribing :)
You deserve way way way way more subs friend. Thanks so much for your help! Your way of explaining (repetitive practises) is so helpful and refreshing for newbies like me
Lol I thought the intro was the video. I had it done before it actually started. Love that you did that begging for the ones like me who are dumb and never watch the whole thing. Got the important bit edited into the first 30 seconds
😂😂😂 When I did this video I really underestimated how much of an issue this would be, I thought by asking this as a question it would encourage all the "newbies" to become "techies"...oh how wrong I was...! That it is, I am doing the video follow-up to answer this question at last...!!!
Thank you thank you thank you from Punta Cana. Nerd is off and I accidentally disconnected the front controller cables. Learned something and very happy
i couldn’t figure out why my pc wasn’t turning on but i knew the power switch wasn’t plugged in 30 seconds in and you taught me everything i needed to know i’ll sub
I really really love an 11:33 long video that is straight to the point with the filler and extra info you may need at the end. Much love man you saved me a mental breakdown all love friend 💪🏻
The power LED and HDD LED connectors can only go one way. If you put it in incorrectly the LEDs won't light up. For power switch and reset switch, doesn't matter. They only short the two relevant pins.
So there’s these pings at the end of the all the led connects and stuff where do I plug in that so I can plug in all the led things into the motherboard
@@yaheardprince you're in no danger of frying anything unless you force a plug or use a header clearly not correct Exception for some mobos pump header used for a fan... If it's a higher wattage, it could be trouble. Double check the motherboard labels closely on these. They're clearly marked.
GOD BLESS YOU MAN, I was giving maintenance to my PC and then it didn't turn on, thanks to this video I was able to find a way to place the power button cables on my pc
just built my PC yesterday. Everything started up and has been running great EXCEPT for the fact I can’t power it down or put it to sleep. If I shut down it turns back immediately, if I put it to sleep, it comes back on. Only way to turn it off is to flip the power supply switch on the back. Any help? My case didn’t have a reset PW. But the rest is all plugged in. Ryzen 5 3600. B450 tomahawk Max. Gtx 1660 super. NZXT h510 case. Power button lights up on the front. But doesn’t do anything when pressed. HELP!!
Got exactly the same problems, It seems my old PC's front panel cable only has 4 pins to connect, I'm either missing half or can't find them anywhere in my system.
@@wlos4029 some old pcs use proprietary connecters so only certain cases work with certain motherboards, but if you could find the pinouts or use an adapter you could get around it.
It's always a good idea to look at your motherboards manual to see where everything goes. They have a diagram in there showing all from panel connection pins and the board is labeled itself sometimes. Don't just go plugging in the cables just anywhere they fit.
Easy peasy to solve the LED/Power SW blablabla situation at the very beginning, time saving tutorial also. Because of you made this simple video and even I am completely brain dead about every single real knowledge of pc still able to understand, I smack the like button and write this long ass comment to express how I feel about this video.
You are a goddamn legend. My PC fans stop spinning and I unplugged the power switch cable along with the Reset switch cable thinking those were the fan cables (I’m a complete and utter noob when it comes to PC stuff) and after plugging them back in the wrong way (unknowingly) my pc wouldn’t start and I started panicking thinking I just broke something. Then I watched this video, plugged them in the right way and now the PC is starting normally… thank you so much! Fans still aren’t working but that saved me a heart attack.
48 Seconds in - and ALL my answers are already answered?! What the heck are the other 11 minutes for?! I'm gonna leave the video running out of pure awe!
Good video. I had a friend help me make a pc a few years back and while I was there when he did it, I forgot about the front panel connectors. Fast forward to a few months ago, I tried installing a better cpu fan and had to mount the brackets to the back of the motherboard myself. Removed the pins to take out the motherboard and didn't find out things were wrong until I noticed my case lights flickering like crazy. Finally solved it by switching the powerled + and - pins around.
Thank you sooo much. I was having a tiny panic attack and then I found this blessed video. But my problem still remains. My pc won’t connect to my mouse, keyboard or monitor. No signal whatsoever. It would be a total blessing if you could assist my problem
You are amazing. Had this problem again and started panicking but I use your video and literally 5 minutes later all connectors working and computer works like a charm.
Dude thank you so much I tried for an hour to figure it out because I was installing new rgb cables for my fans and i couldn’t get to where I needed to do I unplugged the front panel cables not knowing that I forgot how they were and this worked after hours of searching videos thank you so much ❤️❤️❤️❤️
Thank you so much, I was confused as to why my pc wasn't turning on, I just had the connectors in a mixed owner. May Allah bless you for your kind help ❤
This is Ash from HealMyTech & I need your help. I recently suffered a STROKE (end July 2021) which has left me disabled for now (temporarily?), which may have been caused by the VACCINE ASTRA ZENECA. The videos were uploaded on my channel end August 2021. I have set up a GoFundMe, any donations are welcome.
gofund.me/ccb57a48
Here is also my paypal link
paypal.me/healmytech
The links are also in the description with other ways to donate.
ok
My stepdad also suffered a stroke from the vaccine.
Speedy recovery
Hi i need help doing my pannel i have the AsRock B450M/ac motherboard and a Montech pc case
Total anti vaccine moron
Dude! You're a life savior! I pulled those pins accidentally and I was trying to find a vid that helps. They weren't as helpful as yours. My pc is working you just got a new sub!
Thank you and welcome aboard!
Those pins are a pain in the ass to put in when your gpu is installed....then if you bring your pc to a friends house there is always that chance some of them will pop off.
Ikr
@@johnxina3119 same, this video was perfect. nice close up, clear quality, and great explanation.
EXACTLY THE SAME HERE! I was so scared I had broken it as I tried putting them back in myself and I had no luck
ITS 2021 JUST MAKE THEM INTO ONE CABLE ALREADY.
Still not one cable 🤦
@@Kuba_lifts hey update, still not 1
Dude, I can’t thank you enough. I was literally panicking because I accidentally unplugged the pins. My computer turned on and works like a charm! You earned a like and subscribe, man, your a lifesaver.
Ditto!
This saved me! I just got a new motherboard and had that moment where I had everything plugged in, proud of myself, then pressed the power switch and... nothing. Luckily for me, this video exists. Thanks a ton!
got same problem, but i"m pretty certain that i have plugged those wires into wrong place. i have them plugged to JFP2 since that has not worked i will try to switch. also first time the power button was glowing red. honestly this so confusing when my motherboard manual MSI mortar is not explaining it very well. excellent video thanks for uploading it i would be stuck if not for a video on this that is not years old.
pls help me, i have tried everything, i plugged everyting in the right spot on the motherboard while outside the case and it turned on, but when i put the motherboard back in the case and plugged everything in it did not turn on, one time id did turn on while i had the power cable for the motherboard plugged in and the power for cpu plugged in while the motherboard was inside the case but when i plugged in the rest of the cables like usb, audio and other and felt like i was done the power did not turn on... (ive installed all the risers)
MrDiarjo could be a faulty psu
Help me out?
I have all that connected to the motherboard. Where do i put the other side
This just saved me so much money. I worked on my first PC build today for 6 hours straight and was so proud until I pressed the power button and nothing happened. I already gave up, was ready to go to bed and planned to take my PC to a shop tmr to get it fixed. Then I watched this vid while already in bed, jumped up, tried again and voilà. Thank you so much! 🙏🏻😆
Great, direct, to the point. Everything I needed.
Glad you found it useful!
@@HealMyTech1 what does it mean if your h.d.dLed is both negative and positive
@@HealMyTech1 +q/'
@@HealMyTech1 thanks big boss
YOU JUST SAVED ME MULTIPLE HOURS OF STRESSING! I had just built my sons first custom gaming PC and we tried to turn it on, but nothing happened. We were trying over and over to find a problem, and right before we were about to give up, we found your video. After watching it, it instantly fixed our problem. We cannot thank you enough!
I got all the information I needed within the first minute, I'm satisfied and grateful
I took him what 15, 16 seconds.
"There goes my hero, he's ordinary!"
foo fighters hehe
Q - Which of the front panel connectors wire are necessary to at least turn your computer on?
A - The answer is none of them are required. After installing the CPU, and RAM and connecting the PSU cables, you need only short the two Power Switch pins on the front panel block to start the PC. This can be done carefully with a medium blade screwdriver, just touch both of the Power Switch pins with the screwdriver,
As for the situation with the 3-pin Power LED connector....
Case specification several years ago. One of the changes was going from a 3-pin to a 2-pin connector for the front panel Power LED. This is why many cases today have a split connector for the + and - Power LED like you show in your video to accommodate older motherboards with either the 2 or 3-pin connector.
In the case of your MSI board, it has both 2 and 3 pin connectors for the power led to accommodate just about any computer cas you might be trying to use.
On your MSI board, the 3-pin connector is labeled PWR_LED. The 2-pin connector is the one labeled [+MSG-] your motherboard's front panel header. They are labeling it a MSG connector because in addition to providing a steady power-on light. it will also cause the LED to blink in sleep mode and provide other 'messages', using a pattern of blinks to show stuff like P.O.S.T. status or errors.
Good luck!
A
thank you for jumping straight to the point,not wasting my time 🙏
The first 30 seconds of this video solved my issue, thanks a bunch!
Thank you so much, your the only RUclipsr I could find who showed the proper camera angle to get them in, everyone else was either having a seizure with their camera or just not showing the entire socket, I was starting to think I wouldn't find a good tutorial, but here it is.... Liking and subscribing :)
seizure with the camera LMFAO!!!!!!! EPIC
Dude u are op,i browsed all the RUclips but ended up here
You deserve way way way way more subs friend. Thanks so much for your help! Your way of explaining (repetitive practises) is so helpful and refreshing for newbies like me
I appreciate that!
With only 50 seconds of watching and I know exactly what to do. Thanks!! ♡
*Thank you a lot mann! I stayed like a 1 hour to fix it by myself abd i tought i destroyed my pc..... ur my HERO*
I like many other pulled those pins and freaked out when the PC wouldnt boot. You are a lifesaver. LOLOLOL THANK YOU!!
my dad pulled off every piece of wiring thankfully this video exists i hope it works
Did it
Lol I thought the intro was the video. I had it done before it actually started. Love that you did that begging for the ones like me who are dumb and never watch the whole thing. Got the important bit edited into the first 30 seconds
This was perfectly clear and put some worries to rest. Will refer others to this channel
Thank you so much i accidentally unplugged these and now my pc works again W video my guy
Lol dude made the only thing I was wondering about a quiz....
😂😂😂 When I did this video I really underestimated how much of an issue this would be, I thought by asking this as a question it would encourage all the "newbies" to become "techies"...oh how wrong I was...! That it is, I am doing the video follow-up to answer this question at last...!!!
@@HealMyTech1 well I know now that the answer is no but still lol x)
@@thuns6824 thx
@@bulidrians2182
Where is the answer??
Where is the video??
Thank you thank you thank you from Punta Cana. Nerd is off and I accidentally disconnected the front controller cables. Learned something and very happy
Easy help bro thankyou so much best guy out there
Happy to help
i couldn’t figure out why my pc wasn’t turning on but i knew the power switch wasn’t plugged in 30 seconds in and you taught me everything i needed to know i’ll sub
I really really love an 11:33 long video that is straight to the point with the filler and extra info you may need at the end. Much love man you saved me a mental breakdown all love friend 💪🏻
Cheers mate, I needed guidance on this. I was baffled how they seem to be needed to be fitted SIDEWAYS but you've confirmed this, so thanks !
The power LED and HDD LED connectors can only go one way. If you put it in incorrectly the LEDs won't light up. For power switch and reset switch, doesn't matter. They only short the two relevant pins.
So there’s these pings at the end of the all the led connects and stuff where do I plug in that so I can plug in all the led things into the motherboard
@@yaheardprince check your motherboard's manual.
@@yaheardprince trail and error till you find the right way is what I did found it after 2 or 3 times
@@yaheardprince you're in no danger of frying anything unless you force a plug or use a header clearly not correct Exception for some mobos pump header used for a fan... If it's a higher wattage, it could be trouble. Double check the motherboard labels closely on these. They're clearly marked.
@@ronch550what if i lost it?
Dude thank god I came across your video saved our pc build !!!
I Never stop learning. Thank you
dude, you already deserve a medal at the first minute!
Great video. Love the simple instructions, straight to point.
woah. it explained it in the intro. what a legend im subbing
This video helped me turn on my first pc. I had the cables in the wrong spot. Thank you sooo much
No problem 👍
Thanks a lot sir , I only see yours books diagram on 2:41 and fix all the cables in motherboard 😊
Thankyou very much sir
You saved my life. Thank you
This guy just taught me how to use instruction manuals😂 thank you!!!!
Thank you so much!! So straight forward and got right into doing it your a lifesaver!!!
You are welcome!
Bro you saved my life! I accidentally disconnected these wires and i didnt know where did the go. Thanks.
Exactly what I was looking for Sheikh.
You are welcome, and I'm no sheikh, unless you mean buddy...!
DUDE HOLY SHIT I HAVE BEEN ON THESE FOR SO LONG! ITS BEEN FOREVER SINCE I HAD TO DO IT SO THANK YOU SO MUCH, I CANT THANK U ENOUGH MAN
So for the power and reset switch connector, does it matter which way you connect it? That wasn't answered
Did you ever figure this out?
@@whothefuckisdamon7392 if I remember correctly power and reset no, but led yes.
@@Guillotin999 thanks I found the answer and just booted up my first pc build ✌️😊
@@whothefuckisdamon7392 congrats
Finally someone that gets straight to the fucking point thank you
20 seconds in and I immediately discovered what I did wrong. Now I have a working computer!
Alas..i was looking for the power switch connection in my ASUS B450M, this video saved my time.
your turtorial videos helped me so much thank you!
GOD BLESS YOU MAN, I was giving maintenance to my PC and then it didn't turn on, thanks to this video I was able to find a way to place the power button cables on my pc
just built my PC yesterday. Everything started up and has been running great EXCEPT for the fact I can’t power it down or put it to sleep. If I shut down it turns back immediately, if I put it to sleep, it comes back on. Only way to turn it off is to flip the power supply switch on the back. Any help? My case didn’t have a reset PW. But the rest is all plugged in. Ryzen 5 3600. B450 tomahawk Max. Gtx 1660 super. NZXT h510 case. Power button lights up on the front. But doesn’t do anything when pressed. HELP!!
UPDATE FIXED* It was the front panel connectors
@@jeremiahcollins_ how did you fix it?
Got exactly the same problems, It seems my old PC's front panel cable only has 4 pins to connect, I'm either missing half or can't find them anywhere in my system.
@@wlos4029 some old pcs use proprietary connecters so only certain cases work with certain motherboards, but if you could find the pinouts or use an adapter you could get around it.
@@jeremiahcollins_ you c lol love dcxcec so vc de xes
Dude. I was freaking out. My pc wasn't starting at all. Then I did this and everything worked. Thank you so so much.
Answered in 20 seconds, & bob's my uncle
Lol same
this front panel connector portion saved the day. thank you
I might have missed it but does the direction matter for +\-LED and cables that go with it?
For the LED connectors yes you have to put them in the right way. For the switches, doesn't matter.
You got me at the first 30 seconds 🥇 Thank you!
You’re welcome 😊
Thanks for this video I really appreciate it
First 30 seconds fixed my issue. Thanks
It's always a good idea to look at your motherboards manual to see where everything goes. They have a diagram in there showing all from panel connection pins and the board is labeled itself sometimes. Don't just go plugging in the cables just anywhere they fit.
Problem is the manual never tells you which side you plug them in. Label up or down.
No BS and no tiptoeing around just the answers I needed! Thanks! You’re a life saver!
Glad I could help!
Excellent video - really, really helped me out! Thank you for making this video.
U are best teacher instead of other you tuber
You save my life bro. Awesome!
You are an Angel Man,you rescued me, May God Bless you.
0:18 positive and negative And Bob’s your uncle
You and your video saved my life😭😅🤩👏👏
Thanks a lot dude
Easy peasy to solve the LED/Power SW blablabla situation at the very beginning, time saving tutorial also. Because of you made this simple video and even I am completely brain dead about every single real knowledge of pc still able to understand, I smack the like button and write this long ass comment to express how I feel about this video.
Bob’s you’re uncle thank you liked and sub 👍
You are a goddamn legend. My PC fans stop spinning and I unplugged the power switch cable along with the Reset switch cable thinking those were the fan cables (I’m a complete and utter noob when it comes to PC stuff) and after plugging them back in the wrong way (unknowingly) my pc wouldn’t start and I started panicking thinking I just broke something. Then I watched this video, plugged them in the right way and now the PC is starting normally… thank you so much!
Fans still aren’t working but that saved me a heart attack.
ما شاء الله تبارك الله
BarakAllahu Feekum!
48 Seconds in - and ALL my answers are already answered?!
What the heck are the other 11 minutes for?!
I'm gonna leave the video running out of pure awe!
thankyou so much man i was changing all my cables around and i found your video. thanks
5:15
hi Soumya where are you from
Mastering the silicon is the key to success. I like your channel, keep it up! Keep on putting in this kinda work and I'll watch your status escalate
Hey man you probably get a lot of these comments, but this video really helped with my last problem, setting up my PC! Thanks! Now I can game again!
Good video. I had a friend help me make a pc a few years back and while I was there when he did it, I forgot about the front panel connectors. Fast forward to a few months ago, I tried installing a better cpu fan and had to mount the brackets to the back of the motherboard myself. Removed the pins to take out the motherboard and didn't find out things were wrong until I noticed my case lights flickering like crazy. Finally solved it by switching the powerled + and - pins around.
You saved my life I was managing my wires and messed with this. I freaked out when it didn’t turn on
Thank u for getting straight to the point and not waste 5 years to get to the point
Thank you sooo much. I was having a tiny panic attack and then I found this blessed video. But my problem still remains. My pc won’t connect to my mouse, keyboard or monitor. No signal whatsoever. It would be a total blessing if you could assist my problem
thank for getting straight to the point, literally seconds in the video. You got yourself a sub thank you!!!!!!
This was a life saver...those fiddly things are annoying at best.
Pro level youtuber the way you showed how to do it in the first 10 seconds without intros and BS
OH MY GOD!!!!
THANK YOU SOOOOO MUCH!!!
YOU JUST SAVE MY COMPUTER😭😭🙏🙏🙏🙏🙏
MAY GOD BLESS YOU ALWAYS.
TAKE MY SUB👍
thank you so much and thanks for showing it directly in the beginning
this just got you a sub ive been trying to do this fro 6 months and i finally was able to do it after this video tysm
YOU ROCK! I forgot the order SAVED ME
Thank you my Indian brother you helped me now you are the best
#indianlivesmatter
You are amazing. Had this problem again and started panicking but I use your video and literally 5 minutes later all connectors working and computer works like a charm.
no words without saying thank you .feel so much relief after starting my computer following ur instructions🙏🙏🙏🙏❤❤❤
This video saved my life
Dude thank you so much I tried for an hour to figure it out because I was installing new rgb cables for my fans and i couldn’t get to where I needed to do I unplugged the front panel cables not knowing that I forgot how they were and this worked after hours of searching videos thank you so much ❤️❤️❤️❤️
This saved EVERYTHING. Thank you so SO much!
Thank god i found this video! 🙏🏻 I thought I broke my pc and then realised I just plugged the cables wrong (o.O') THANK YOU SO MUCH!!!
BRO I THOUGHT MY £2000 PC WAS BROKEN I TOOK THESE OUT BY ACCIDENT LAST NIGHT WENT TO PLAY NOW AND OMG YOUR A LIFE SAVOUR BRO ❤️❤️❤️
Thank you so much I was so scared that I had broken my computer and this was also my first time building my own computer so thank you
Thank you so much, I was confused as to why my pc wasn't turning on, I just had the connectors in a mixed owner. May Allah bless you for your kind help ❤
Life saver that's never been so more clearly explained to me, THANK YOU
Finally got my PC working!! Really appreciate it
Give this guy a medal
Wow. First 45 seconds solved it. I think I had it wrong before and it was shocking the crap out of my case.