I am teaching Power Systems as an emergency backup prof. I am like the Prof. version of a CB DS combination. Thanks for the helpful video I will show to my class!
Great!! Also you can check out below course courses.theelectricalguy.in/courses/Circuit-breaker-control-Schematics-Masterclass--Beginner-to-Advanced---647b08bce4b08fb4470c3021
Hello Sir. Thanks for the video, although I have a question: you said that circuit breakers operate automatically, but I'm studying a Protection Systems course and we've learnt that it is a relay what trips the circuit breaker. So, when you said that a circuit breaker was automatic, were you also considering its relay?
Hi I have a home theater and i have a indivual breakers ..1 rcd and 1 surge protection devices ..all dedicated just for the home theater..i want to remove as less interference and noise and have clean power as possible so i was wondering if i should get a seperate isolator as well ? Will that potentially stop any interference and noise etc coming and produce clean power?
Sir, u r The master of electrical field . One doubt 4:28 in video u said close the disconnector for continue the bus So obviously current flowing through disconnector so why at starting u said there is no for normal current & fault current ( off load Switch ) How ?. Sir please clear my doubt
Good question, I noticed this part aswell. This might cause some confusion. A disconnector can open or close on a bus while there is power. but in order to do so there is usually a section to link/couple bus 1 and bus 2. This has to be done with a circuitbraeker. then there is no current flowing through a disconnector when you change to the other bus. So in steps it would look like this: 1. close curcuitbreaker to couble bus 1 and bus 2 2. close disconnector 2 in the section you want to switch. 3. open disconnector 1 in the section you want to switch. 4. open circuitbreaker to seperate bus 1 and 2. because you close disconnector 2 before opening disconnector 1 the current keeps flowing through the side thats closed. opening the disconnector in this case is done while the power is on but the load is distributed.
hi. you need to have information on all the types of equipment used in a substation before going to interview. I have a video series on substation equipment on youtube, you can watch that.
I really like your videos. My interest in substation primary and secondary systems. It will be awesome if you post some videos of relays and auxiliary systems in substation and how to do setting for MICOM, RELION AND SIPROTEC relays.
where have you been all this time !!!! I'm almost done with the course and this is when I get such a great explanation??? Thank you !
Have been confused for days... Thanks to you explanation, all my confusion has been drastically reduced... Thanks Sir!
We got a lot of information from ur videos 👌👌👌👌👌
It clarifies all the doubts...got to understand so easily.
Thank you ☺️ do share and subscribe to my channel ☺️✌🏻
I am teaching Power Systems as an emergency backup prof. I am like the Prof. version of a CB DS combination. Thanks for the helpful video I will show to my class!
Glad it helped! 😇
ur videos are helpful for facing the interview
Just started a substation job and this is helping me understand a little bit better
Great!! Also you can check out below course
courses.theelectricalguy.in/courses/Circuit-breaker-control-Schematics-Masterclass--Beginner-to-Advanced---647b08bce4b08fb4470c3021
Thanksអគុណបង👍👏
really helpful video! Thank you very much
Perfect we learn more from ur videos. Make video on Sf6 gas and switch gear short video
Video on sf6 gas - The things you don't know about SF6 gas | TheElectricalGuy ruclips.net/video/sbsFMmeQ8ho/видео.html
Nice explaination.. if you provided pictures of both components it wd be more perfect
Use a disconnector for discharging a high voltage transformer when a circuit beraker is connected before a large high voltage arcing going to stopped
Thank you so much for this amazing video
Do share and subscribe to my channel 😊
thank you very much sir
Hello Sir. Thanks for the video, although I have a question: you said that circuit breakers operate automatically, but I'm studying a Protection Systems course and we've learnt that it is a relay what trips the circuit breaker. So, when you said that a circuit breaker was automatic, were you also considering its relay?
Yes, of course. It operates on relay command .
@@GauravJ Thanks!
Brother relay is the brain of CB
Great 👍
provide videos for why we are using delta connection in transmission side and start connected in distribution side
Hi
I have a home theater and i have a indivual breakers ..1 rcd and 1 surge protection devices ..all dedicated just for the home theater..i want to remove as less interference and noise and have clean power as possible so i was wondering if i should get a seperate isolator as well ? Will that potentially stop any interference and noise etc coming and produce clean power?
very well explained..
Thanks 😊 do share and subscribe to my channel 😊
nicely explained dear
Sir, u r The master of electrical field . One doubt 4:28 in video u said close the disconnector for continue the bus So obviously current flowing through disconnector so why at starting u said there is no for normal current & fault current ( off load Switch ) How ?. Sir please clear my doubt
Good question, I noticed this part aswell. This might cause some confusion.
A disconnector can open or close on a bus while there is power. but in order to do so there is usually a section to link/couple bus 1 and bus 2.
This has to be done with a circuitbraeker. then there is no current flowing through a disconnector when you change to the other bus.
So in steps it would look like this:
1. close curcuitbreaker to couble bus 1 and bus 2
2. close disconnector 2 in the section you want to switch.
3. open disconnector 1 in the section you want to switch.
4. open circuitbreaker to seperate bus 1 and 2.
because you close disconnector 2 before opening disconnector 1 the current keeps flowing through the side thats closed.
opening the disconnector in this case is done while the power is on but the load is distributed.
Great explanation 👍⚡⚡⚡
Thanks 😊 do share and subscribe to my channel ✌🏻👍🏻😊
Very good
Sir maximum what number of transformer can be connect in parallel?
Hon. Very good.
Perfect
what is the electrical equipment interview asking sir
hi. you need to have information on all the types of equipment used in a substation before going to interview. I have a video series on substation equipment on youtube, you can watch that.
thanks alot
Great video but where does a switchgear fall under?
Thanks. Try watching this video where in i talk about the types of switchgear.
ruclips.net/video/8nPl2EQWP1c/видео.html
I really like your videos. My interest in substation primary and secondary systems. It will be awesome if you post some videos of relays and auxiliary systems in substation and how to do setting for MICOM, RELION AND SIPROTEC relays.
Thank you my friend. I’ll try to post videos on the topics you have suggested.. !
Excellent
Thanks
អគុណបង
Thank you so much
What is mean by PF Withstand Voltage and Impulse Withstand Voltage of Vacuum Circuit Breaker ?
Hello Bharat.
Check out this video. I have explained the nameplate details of VCB.
ruclips.net/video/yAX3ZiRxL9A/видео.html
@@GauravJ thnku very much sir.🙏🏻🙏🏻
Thx
sir please upload the new "video"
New videos will be published on 15th and 30th of the month.
Gaurav J - TheElectricalGuy Thanks for responding
👌🏻
よーし👍🏻👍🏻👍🏻