This is no joke folks. I just upgraded Speedybee F405 V4 to inav7, and successfully configured the timer/motor/servo mixing for a bicopter in Chinook configuration. Had it running smooth full duration flights within an hour of firmware update using previous settings from inav6. Fine tuning done with the phone app. ......and I never had to go into CLI !!
Hello and thank you for your valuable time and commitment, not to leave out all the other hard working contributors. "Bravo..." Inav is just "Awesome!!!" Was Excited to flash the new Inav 7 on a re-work of a Darwin 129 with a SB F7V2 Fc (made a custom target to remap CC pin for servo use to do the Camera tilt thing), new M10 GPS, Mateksys optical flow/lidar. "All is working beautifully", will try Cruze Mode this weekend. Yippee... 😁 Hope you and everyone has a great upcoming holiday! Thank you... Ps, love the hat, have to see how to get one here to Mexico (shipping can be "well challenging at times, they will really like or lose your Stuff, only sometimes though"
One thing I experienced is on the output tab it took several times to get all motors to spin. Three would spin then i would reboot and 2 would spin then i would reboot and 3 would spin.And finally all 4 spun.
Great release and great video. but I saw few bugs .... perhaps only on my board (Speedybee F405 wing). "save and reboot" button does nothing in the 4 PID pages in 7.0.0 Configurator and flight mode changes (accro manual horizon) are often very long to change on the flight controller when I move the corresponding switch on the transmitter ... and sometimes the mode doesn't change at all (it stays on the last mode selected in the LUA script and also on the telemetry page [TX16S] but I can see the "FM" telemetry information updated many times each second)
Oops, I must correct my previous comment, the ""save and reboot" button does nothing in the 4 PID pages" still remains, but for the second bug that was my fault, I tried to activate "Permanently enable Launch Mode for Fixed Wing" to see how it works ... so it was in "launch mode" and it stays in "angle mode" waiting for the launch ... so sorry. have a good day
Thanks for all the great work! After the 8.* release in the future, can/will bug fixes (or really minor improvements) in the 8.* branch be merged down into the 7.* branch too (if compatible) so that F411 users can still get the best of INAV? Or do the releases for every major version simply come to a dead end once the next major version is released? I'm sure a lot of analog fixed-wing pilots have F411 boards still in use because they're fine with old VTXs that don't need a serial connection.
Hi Pawel, I just switched to 7, but I have a question, is there any indication when the Speedybee app starts supporting the INAV 7 via WiFi/Bluetooth? Because I build a Siccario, but PIDs are not great yet and every time I want to access the USB port disassemble the frame. Or is there any other way I can connect wireless to my Tmotor F7 pro? I am not able to find any USB-C extension cable which works with my FC, please help, thanks
Hi Pawel. I have a 6 inch FPV multirotor drone. Which preset profile should I select after I have flashed INAV 7? Currently I only see the preset profiles for Multirotor 3, 5, and 7. Hope to hear from you. Thank you.
Hi, please help me, I am currently using Inav 7.1, I have a Air speed sensor, when I turn on the plane and the FPV, the sensor starts at 5K/h, I wonder if the air speed sensor can be calibrated in INAV? Thanks
Nice release. Still have few questions: 1. does it have geofence and geo-awarness capabilities ? 2. does it the possibilty to have a speed limitation ?
Hallo ich möchte einen Copter bauen und habe noch einen Mateksts F722-hd meine frage wäre ob ich denn mit inav verwenden kann. Eine DJI O3 möchte ich auch noch verbauen .
Thanks so much for all the hard work on this project. I am currently a BF Quad user. I want to switch to iNav. Do you plan on producing a new series of iNav 7 Tutorials? In the mean time, which of your playlists would you recommend? There is a newer FPV quad playlist or there is a much older iNav playlist?
@@FPVUniversity Thanks so much. I looked through your playlists and the only one I could find that looks like a complete Quad inav setup playlist was for iNav3. Do you mind giving me a link to the iNav 6 playlist you mentioned?
hello, I have mamba f405 mk4 2022b, and my vtx (dji o3) is always turn off when I flashed the FC to inav 6.1.1 or 7 RC3, but it came back on when I flashed the FC back to betaflight... I'm sure that I'm using the right firmware and I've flashed 6 times back and forth between inav and BF, and the problem remains the same... can you help me?
Witam, Dopiero zaczynam przygodę, i nie mam pojęcia o czym mowa ...mam speedybee v4 i kończę mój pierwszy dron na o3 . Przeskok z ukochanego DJI FPV....także od czego zacząć beta fly czy może INAV 7? Czego się uczyć? To polski projekt czy twoja praca? Pozdrawiam `
Hi Pawol, thanks a lot for all this job I decided to try this instead of Betaflight. Recently I flashed INAV 7 Firmware to my Skystars F722 HD Pro4 FC. In INAV the target is SKYSTARSF722HD. I selected lates stable version and flashed firmware. But INAV doesn't detect anything except barometer so at the end it is not working at all. Is there some trick how to fix the problem? Thanks a lot.
Thank you for all of your hard work Pawel. I recently built my first 7" quad and have configured it with INAV 6 (I have never used BetaFlight or earlier versions of INAV). Is migrating everything from INAV 6 to INAV 7 pretty painless? Is there anything I should be aware of? Should I just erase before flash and start from zero? I plan on migrating very soon as I am VERY interested in the cruise mode and the simplified tuning. I am only hesitant because INAV 6 is working so well that I don't want to risk messing up my configuration 😂.
Kolego właśnie próbuję odpalić Dolphin FPV ze SpeedyBee 405 Wing na pokładzie i natknąłem się na dwa problemy. INAV 7 nie reaguje na drążki kotrolera. Używam Radiomaster pocket i odbiornik ERLS Radiomaster RP1. Radio binduje się z odbiornikiem. używam najnowszej wersji ERLS 3.2.0. W INAV w zakąłdce recivier wszystko ustawione jak należy (Serial, CRSF). Drógi problem to serva (ja się je mapuje )
Trying to upgrade from iNav 5.0 to 7.1… 5.1 and 7.1 configurators connect without issues. However when I try to flash, it just shows “ connected to: Com4 “ and does nothing… what am I missing?
New to inav 7 bit confused about switching motor mapping using wizard Am I supposed to allocate the motor that is spinning to the position it should be Thanks for your help
That's a great achievement mister Pawel 👏 Thank you Do you think it's safe enough to make a Quad Auto launch mode? when you throw the drone it will fully arm and stabilize In air, with GPS and Mag... It's too crazy to ask for it?
I use 7 RC3 with a VTOL. Can i copy my DIFF into the final 7.0 and it's all good? Of course everything will be checked again before the flight. Great work on iNav 7 😊
Never really dipped my feet into INav, but I think this update will make it try it out. Is a compass still required for the good GPS function for drones?
DSHOT support and F405 v3 support - that is all I want to hear. Going from Betaflight to INAV, because, IN RTH WE TRUST! I want cruise, loiter, alt-hold modes badly. Being able to fly only freestyle with the "fall from sky if the radio is lost" feature is honestly boring.
![Lethal Company Music Video 🎵 "Follow The Orders" [VERSION A]](http://i.ytimg.com/vi/QeooZB4Z7RA/mqdefault.jpg)
I will consider switching from Betaflight to INAV7 😍. Thank you for your exceptional videos and guides!
Have fun!
Thanks to INAV developers!!! Thanks to your channel as well
Our pleasure!
Good work guys. Have a VTOL Albabird build underway.
This is no joke folks. I just upgraded Speedybee F405 V4 to inav7, and successfully configured the timer/motor/servo mixing for a bicopter in Chinook configuration. Had it running smooth full duration flights within an hour of firmware update using previous settings from inav6. Fine tuning done with the phone app.
......and I never had to go into CLI !!
It's pretty sweet indeed!
Hello and thank you for your valuable time and commitment, not to leave out all the other hard working contributors. "Bravo..."
Inav is just "Awesome!!!"
Was Excited to flash the new Inav 7 on a re-work of a Darwin 129 with a SB F7V2 Fc (made a custom target to remap CC pin for servo use to do the Camera tilt thing), new M10 GPS, Mateksys optical flow/lidar. "All is working beautifully", will try Cruze Mode this weekend. Yippee... 😁
Hope you and everyone has a great upcoming holiday!
Thank you... Ps, love the hat, have to see how to get one here to Mexico (shipping can be "well challenging at times, they will really like or lose your Stuff, only sometimes though"
In RTH we Trust👍💪
yes we do!
Proven reliability for planes AND long range quads (quads autoland on the helipad and auto-disarm 🙂 ).
Saved my ship more than once.
I miss the release during a live stream, but you got already 182 thumbs so time for me to add 1 now. Great work.
I appreciate that!
Darn my matek F411 wings were my go to FC's in small planes. They just won't die no matter how much I abused them.
They are great flight controllers.
VTOL support, yeaaah! 🔥🔥
I suggest you to make a video tutorial on the topic!
Thanks Pavel and to the whole team👍🏼👍🏼✈️✈️🫡
Thanks
These major releases have been coming thick and fast!
Major comes every 9 months or so. It's not our fault Betaflight slowed development so much and they have no major features to release anymore
@@FPVUniversityhi ps what do u think of open tx have they added touch screen support yet or not. Coming back to the hobby after 2 years
@@FPVUniversityor should i move to edge tx and what is the diffrence is edge tx ok to use.
Sweet thankyou upgrading my fleet today 🎉
Enjoy it
YAY! get the higher refresh rates and more constellations 'back' for the satellite receivers. My M8N Neo will be so happy.
Enjoy!
Amazing work, thank you! 🙏🏼
Thank you too!
One thing I experienced is on the output tab it took several times to get all motors to spin. Three would spin then i would reboot and 2 would spin then i would reboot and 3 would spin.And finally all 4 spun.
Awesome! Thanks for the news, Pawel! 😃
Stay safe there with your family! 🖖😊
And happy holidays!
Same to you!
Bravo.thenks.Go ahead
Great release and great video. but I saw few bugs .... perhaps only on my board (Speedybee F405 wing). "save and reboot" button does nothing in the 4 PID pages in 7.0.0 Configurator and flight mode changes (accro manual horizon) are often very long to change on the flight controller when I move the corresponding switch on the transmitter ... and sometimes the mode doesn't change at all (it stays on the last mode selected in the LUA script and also on the telemetry page [TX16S] but I can see the "FM" telemetry information updated many times each second)
Oops, I must correct my previous comment, the ""save and reboot" button does nothing in the 4 PID pages" still remains, but for the second bug that was my fault, I tried to activate "Permanently enable Launch Mode for Fixed Wing" to see how it works ... so it was in "launch mode" and it stays in "angle mode" waiting for the launch ... so sorry. have a good day
Crikey, iNav is looking more attractive to me than Betaflight, because of this.
Now, all I need to do is make the switch.
yes, you should
@@FPVUniversity Already done so.
Now, I am up to upgrading the GPS module in my quad to one with a built-in compass.
This is where the fun begins! 😈
Amazing, just amazing 🔥🔥🔥🔥
thanks
Thanks for all the great work! After the 8.* release in the future, can/will bug fixes (or really minor improvements) in the 8.* branch be merged down into the 7.* branch too (if compatible) so that F411 users can still get the best of INAV? Or do the releases for every major version simply come to a dead end once the next major version is released?
I'm sure a lot of analog fixed-wing pilots have F411 boards still in use because they're fine with old VTXs that don't need a serial connection.
Yes, F411 were very popular. New flight controllers of the same size like the F405 are quite more expensive now.
Thanks for the great video. I have a 10-inch hexacopter that sometimes doesn't stabilize. What can I do?
Quick question: is osd now fully supported with inav for dji o3? Or is it the same bf compatibility mode? Thank you!
I am wondering this too!
@@VideographerBill found out, it is not, same as inav 6, but good enough for what i common use 🙆♂️
What is ez_filter_hz. Can’t arm
Hi Pawel,
I just switched to 7, but I have a question, is there any indication when the Speedybee app starts supporting the INAV 7 via WiFi/Bluetooth?
Because I build a Siccario, but PIDs are not great yet and every time I want to access the USB port disassemble the frame.
Or is there any other way I can connect wireless to my Tmotor F7 pro? I am not able to find any USB-C extension cable which works with my FC, please help, thanks
Congrats 🎉
thanks
Hello from Brazil 😊
Hello 👋
Wonderful
Hi Pawel. Any chance for inav will work with mamba f435 ai stack?
Can INAV7 be configured to control the VTX power from the radiomaster TX12 MKII ELRS transmitter?
Good evening, I have a problem with Mateksys H743 V3 with the GPS not keeping position and difficult to arm the drone
thanks Pawel!!!!
Hi Pawel. I have a 6 inch FPV multirotor drone. Which preset profile should I select after I have flashed INAV 7? Currently I only see the preset profiles for Multirotor 3, 5, and 7. Hope to hear from you. Thank you.
Try5" and try 7". See which one performs better :)
@@FPVUniversity thank you Pawel. I will give it a try. 😊
Hi, please help me, I am currently using Inav 7.1, I have a Air speed sensor, when I turn on the plane and the FPV, the sensor starts at 5K/h, I wonder if the air speed sensor can be calibrated in INAV? Thanks
Nice release. Still have few questions:
1. does it have geofence and geo-awarness capabilities ?
2. does it the possibilty to have a speed limitation ?
take a look here ruclips.net/video/qxkhDCLynU4/видео.html
Hallo ich möchte einen Copter bauen und habe noch einen Mateksts F722-hd meine frage wäre ob ich denn mit inav verwenden kann. Eine DJI O3 möchte ich auch noch verbauen .
Sir, you are my go to everything about inav, can I have a request? To add target to inav for Flight controller Aikon F7 AIO.
Where can I get the INAV cap?
Switched over from BF 4.4.2 and I preferred Inav!
Link in description :) bit.ly/3GezzBq
Thanks so much for all the hard work on this project. I am currently a BF Quad user. I want to switch to iNav. Do you plan on producing a new series of iNav 7 Tutorials? In the mean time, which of your playlists would you recommend? There is a newer FPV quad playlist or there is a much older iNav playlist?
The INAV 5 and 6 series are still valid. I mean proces should be very similar. But yes, I think I will have to record a new series early next year
@@FPVUniversity Thanks so much. I looked through your playlists and the only one I could find that looks like a complete Quad inav setup playlist was for iNav3. Do you mind giving me a link to the iNav 6 playlist you mentioned?
hello,
I have mamba f405 mk4 2022b, and my vtx (dji o3) is always turn off when I flashed the FC to inav 6.1.1 or 7 RC3, but it came back on when I flashed the FC back to betaflight... I'm sure that I'm using the right firmware and I've flashed 6 times back and forth between inav and BF, and the problem remains the same... can you help me?
hello, is it possible that after the automatic takeoff the plane turned its wheels instead of flying further, inav programmers should do this
Witam, Dopiero zaczynam przygodę, i nie mam pojęcia o czym mowa ...mam speedybee v4 i kończę mój pierwszy dron na o3 . Przeskok z ukochanego DJI FPV....także od czego zacząć beta fly czy może INAV 7? Czego się uczyć? To polski projekt czy twoja praca? Pozdrawiam `
Jak z DJI FPV to zdecydowanie INAV. A INAV to project międzynarodowy, ja tym tylko zarządzam
@@FPVUniversity szacun, klasa i poświęcenie...będę uczył się na INAV...thx
Hi Pawol, thanks a lot for all this job I decided to try this instead of Betaflight. Recently I flashed INAV 7 Firmware to my Skystars F722 HD Pro4 FC. In INAV the target is SKYSTARSF722HD. I selected lates stable version and flashed firmware. But INAV doesn't detect anything except barometer so at the end it is not working at all. Is there some trick how to fix the problem? Thanks a lot.
Probably manufacturer put a different gyro. Make a issue on INAV GitHub and write down which gyro Betaflight detects
Hi sir, can you add firmware target for iflight blitz_f7_aio ?
Thank you for all of your hard work Pawel. I recently built my first 7" quad and have configured it with INAV 6 (I have never used BetaFlight or earlier versions of INAV). Is migrating everything from INAV 6 to INAV 7 pretty painless? Is there anything I should be aware of? Should I just erase before flash and start from zero? I plan on migrating very soon as I am VERY interested in the cruise mode and the simplified tuning. I am only hesitant because INAV 6 is working so well that I don't want to risk messing up my configuration 😂.
I see first problem in VTOL. It can be tricopter + plane. Looks like not support quad + plane. Am I correct ?
It supports everything as long as you have enought outputs to setup both mixers and connect everything
Kolego właśnie próbuję odpalić Dolphin FPV ze SpeedyBee 405 Wing na pokładzie i natknąłem się na dwa problemy. INAV 7 nie reaguje na drążki kotrolera. Używam Radiomaster pocket i odbiornik ERLS Radiomaster RP1. Radio binduje się z odbiornikiem. używam najnowszej wersji ERLS 3.2.0. W INAV w zakąłdce recivier wszystko ustawione jak należy (Serial, CRSF). Drógi problem to serva (ja się je mapuje )
Trying to upgrade from iNav 5.0 to 7.1… 5.1 and 7.1 configurators connect without issues. However when I try to flash, it just shows “ connected to: Com4 “ and does nothing… what am I missing?
Matekf405SE
New to inav 7 bit confused about switching motor mapping using wizard
Am I supposed to allocate the motor that is spinning to the position it should be
Thanks for your help
yes, exacly. And mixer will make all required adjustments
How does Inav7 compare vs Betaflight 4.4.5?
But in which aspect? I have a dedicated video on this topic ruclips.net/video/s-xxiiP7oik/видео.html
Sir, can inav 7 use standalone compass such as GY-273
yes
Where is the EZ Tune in inav 7.1?
Why doesn' t work my M80 GPS at INAV 7.0
That's a great achievement mister Pawel 👏 Thank you
Do you think it's safe enough to make a Quad Auto launch mode? when you throw the drone it will fully arm and stabilize In air, with GPS and Mag... It's too crazy to ask for it?
Well, if you convince any developer it's worth to do it ;)
I use 7 RC3 with a VTOL. Can i copy my DIFF into the final 7.0 and it's all good? Of course everything will be checked again before the flight.
Great work on iNav 7 😊
yes, INAV 7 RC will be compatible with stable release
Hi Pawel, can I use the config file from INAV 7 RC?
Yes, you can
inav dose not work with adrino pilot misson planner any more that sucks the drone dose not show up on the maps any more
Great Guys! Thank you!
Our pleasure!
Never really dipped my feet into INav, but I think this update will make it try it out. Is a compass still required for the good GPS function for drones?
You will need a compass for RTH and all autonomes flight modes but not for acro and angle.
@@BBFPV sweet I already flashed it and my GPS had a compass 😂. I managed a hover then I had to leave for work.
@@IggyBiggy👌
👍👍👌
DJI O3 this is possible. I would not be happy to receive an answer.
Can the GPS component manage simultaneously several constelation?
yes. It was always like that
You cannot use Glonass AND Beidou at the same time because they use the same band. So it's GPS and Galileo and Glonass OR Beidou.
Does every fc support vtol ? Can i use a separate PDB and a non-vtol fc ?
FC has to have enough outputs to connect all required servos and motors
@@FPVUniversity Fantastic, I can't wait to build a vtol plane 🤩🤩. Never been this hyped up about fpv for years!
EZTune is missing a switch to enable RPM filtering.
INAV flies greeat without rpm filters. So whatnfor?
Speedybee f405 V3 ? How's it performing.... Any one tested ?
It's all fine. Issues fixed
@@FPVUniversity thank you sir @FPVUniversity
F411 😢 Price of progress...
F411 😢
DSHOT support and F405 v3 support - that is all I want to hear. Going from Betaflight to INAV, because, IN RTH WE TRUST! I want cruise, loiter, alt-hold modes badly. Being able to fly only freestyle with the "fall from sky if the radio is lost" feature is honestly boring.
Or HERself…