With the battery holder, to reinsert a new battery properly without having to push back the spring so far, it is easiest to actually slide in the battery from the opposite side and then push it under the plastic clips. That means that you insert it from exactly the opposite side that you removed it from.
that is the way its supposed to be installed put the battery in under the tabs and then it just goes in without any prying of the spring The spring is for removal I've never seen anybody try to install it the other way I was so confused when he did that XDD But i mean its a simple mistake i guess xD
Very nice job! Thanks for including the part where you mistakenly broke the battery holder. It was good to see that anyone can make such mistakes. I usually bash myself way too much when I make a mistake but realized that if I stop there and think about it, I can come up with a fix rather easily. You might be able to remove those light (black) spots/lines from the top of the PS2 by gently using a magic eraser if the plastic isn't painted. (The silver one I have seems to be painted plastic and even alcohol can damage it but I'm not sure about the white one)
The white one isn’t painted. I had one that was dropped on a front corner and used a box knife to shave off the plastic to make it more normal. It was all white plastic so that may work.
Indeed it's a matte finish similar to the black version (not silky smooth like the silver which I believe is painted). I'll give it a shot. Not sure what those marks are but they are in there pretty good.
It surprises me how that tiny little board can run all of the games released on it, some of them being quite big, while looking good. Never opened mine, and never will, this was a nice little showcase, thanks :D
Nice Video and Restorations,,the Door Repair and the Battery Holder replacement are new to repair, so liking the video..pls more restorations to come with errors like this that you fix...
Hell Yeah! I've retrobritened a ton of these ceramic white ntsc-js over the past couple years. They clean up super well. Working on getting some harder to find Ps2 modchips currently, let me know if you'd like one to install and I'll send one your way :D -Modz
Haha thanks for the offer man. So what you're really saying is you're keen to see a fail video of "how not to install a mod-chip in your PS2". That Voultar install vid on the system you sent over didn't look like a project for the faint of heart. Okay, I might be up for the challenge, although it will certainly be the most difficult project I've tackled to-date...
@@BorderlineOCD haha dude you got this! I sent Voultar a 90k model. The 79k and 90k require those super hard connections. Anything earlier then that is significantly easier. You’ll be fine 🤘🏻
Had to tear down my SCPH-77001 to lubricate the optical drive assembly, and it was surprisingly clean given how old it is. Though with the fan, I wasn't able to give it oil because it seems to be a model without a "oiling" hole. Dunce me also dropped one of the fan screws inside the heat sink, and I had a hard time trying to get it out without disassembling the whole thing, since it has a modchip installed and I don't like stressing old wires XD. At least I got it out and put it back together with a now quieter disc drive!
I loved this restoration. Ive been doing refurbishments for about a year myself and PS2 slims are by far no joke. Some of the most fragile little pieces can easily upset you. Im glad you pointed out the ribbon cable being able to scratch discs... this happened after refurbishing my Dads PS2 back in December as well as his power button having so much junk built up over 17 years that it just broke off. I had to use a donor for the power button but I did that and a couple others that also gave me a headache.
Thanks for covering a PS2 slim! You should put on the title or description what model it is, since these are so different between each other and it would help crank up the views. I for one own a SCPH-70007. I cleaned its fan but the loud whirl at startup continues, however it's quiet after that, and I noticed the unit gets rather hot while my SCPH-90001 doesn't, while its fan is much louder in return. Also love how you dealt with the coin cell holder, magnificent.
Every video you put out makes me one step braver to attempting a capacitor replacement on my first ps3 fat my dad bought me in 2007. Your videos are so intriguing and I want to thank you C:
Out of all my consoles I've repaired, the PS3 fix is still the only thing I'm holding out on and the only one I have left to repair. It's the only one that makes me nervous.
Its an animal just to warn you. I ended up breaking one recently because I decided to clean the optical drive and theres a ribbon cable that goes underneath the power supply so I removed that power supply a good 20 times and now the system has no power. I wouldn't attempt a PS3 fat unless you are decently experienced
Your pain on the battery holder is everyone's gain! Thanks for warning us and showing us how to replace it. Be careful about that fragile part! There are much better battery holders, and this one in the PS2 Slim is not the best design. The way I did it after watching this video was bend the fragile piece back like he did and gently help the battery out. For the new battery, I bend the same piece back, and put the battery under those tiny pieces of metal and gently helped the battery in from the other side. Also, after 20 years, my PS2 Slim 77001 was still keeping date and time, but since I was in there changing out the laser, I did a major clean up and decided to change the battery as well. Surprisingly, the old battery still reads 3.1 volts! Most of the time, my ps2 is plugged in 24/7 so it barely drained the few times it was disconnected. I'll use the old battery in something that is less difficult to change like a key fob for a car.
I have just recently started out fixing broken PS2's and found this video incredibly helpful. Thank you very much for how clearly you explained each step in the video. Great work with the memory card flap too. Great video. 👍👍
Great restoration on that beautiful white PS2 slim! I don't see those a lot these days. Great job fixing the Memory Card door issue! In the past when I was working on my PS2 Slim 9k, I had similar problem on the second MC door where the post just breaks off. I cringed (and swearing) seeing that happened. Not knowing the solution to fixing the post, I end up doing a case swap from a spare parts PS2 that I had laying around in my storage. It seems the post that holds the second MC door is very fragile (a flawed design for the PS2 slims? Probably) on the PS2 slims if one is not careful when working on their console. So when I see you using a epoxy putty to create that post and testing it, I was surprised that it's possible to fix it. I think you're the first person (that I know) who actually shows a solution to fixing that problem. Now I'll be definitely going to buy epoxy putty just to do that fix if my MC door on my PS2 slim breaks off again. I wonder if it will work on the broken screw post that holds the case together....🤔
For a broken screw post I prefer the regular PlasticWeld epoxy, assuming you still have the broken post. You can cover the screw hole with some tape, epoxy it in place and drown it/wrap it in epoxy if it needs to be structural.
@@BorderlineOCD The ones on my PS2 slim are long gone however I can try that with my Guitar Hero Live controller as the screw post on one of the bottom screws has broke off (probably someone work on it before. I will try that, thanks for the tip.
Just thought I'd mention that this has inspired me - I'm currently restoring a CECHC03 and I'm now sold on the idea of respraying it white. I'm not too good at the soldering side yet but I've been painting things for years, so thanks for working on a white console haha
Now we lubricrate the shaft made me giggle :) Great work and another PS2 saved and with the battery connector we see even professionals can have badluck or seeing things over.
Was just working on one of my PS3 slims and ran into a situation where I was trying to change the battery, which is in a similar bracket as your PS2, and I pressed on those little tabs probably harder than I should have. Fortunately for me they didn't break but watching your made the made my hair stand on end because I realized that I was probably extremely lucky. Had they broke I wouldn't have had a replacement and would have been SOL! Though it sucked for you, I'd glad I got to see it because now I know how fragile they can be!
Found one of these for 50£ On eBay and arriving tomorrow! Love your videos and this one came just at the right time as my Slim will need some TLC as well :D
Nice restoration, out of all the slim models this is my preferred one as it's not prone to the laser ribbon scratching the disc with age - it's the only model to use clips on the bottom case to hold it down rather than adhering it to the top shield. Runs fairly cool and quiet too, especially compared to the 7000x!
I usually use 3-in-1 oil on fans, but lithium grease looks like a good solution, too. The difficult part is when you run into fans that have a tiny opening, you almost need a syringe with a needle to get it in there. Nice work on this PS2, it definitely needed some love.
Seeing your master system on the shelf makes me miss mine so much, so nice to see one again. Video really makes me want to repair my ps2's issues with its disc drive.
I wondered when companies started using the evil ribbon cables... One of the reasons I don't dare open up the 3ds. So easy to break these when compared to nes/snes.
That's a quality bodge for the battery. Nice and solid. I suppose you could have also used a save battery meant for a cartridge style game but then not easily replaceable. For the fan, I normally use sewing machine oil, 321 oil, or some type of light machine oil. I'm not sure lithium grease will get liquid enough to get down there and lube things up but it sure was quiet. Maybe from just being super cleaned. Anyways, great work.
Thanks again for sending the system over, it was a fun project! You know it didn't occur to me to solder a save battery with welded on terminals, and I actually have a bunch of those for cart battery replacements albeit they are generic and I can't find any from reputable brands. Good idea though and that would have been just fine with me considering it's always easy to solder in a replacement.
Great video! I have restored a bunch of ps2 slims over the years and I still dislike them. You did a great job with the binding post repair for the memory card door. I've use sugru in the past with similar success. Looking forward to your next video!
15:00 Hey! That's a 70k model! You could add the IDE-Connector! You can also attach an SD adapter/converter to that and since the drive is already gone anyway, this is a good place to position it. It is also THE ONLY Slim PS2, which allows booting FHDB and the HDD-OSD via/through FMCB! ;)
Thanks for the tip! That particular unit might be a bit too far gone to do much with given the amount of rust but to be honest I haven't tried powering it up as it's also missing the power button board. Who knows though, maybe it can be saved. If not, I'm sure it will lend a part or two for a future repair.
16:49 Also me when closing up a console that will likely never be opened again. I'm a new viewer but I love that I already got my answer as to why your channel is named what it is haha
For a quicker job on plastic repairs, try the super glue and baking soda method. It can be sanded, filed, etc afterwards. You have to have the runny super glue though, I've tried it with gel to no luck. I've fixed broken clip tabs, standoff holders, screw posts, flip down doors on old CRT monitors, etc and just to be on the safe side, you can even hit the job with activator spray after to ensure an instant cure.
PS2 is the shit!! Love it forever! Borderline, make sure to adjust the ribbon cable for the laser. It can get up after some time, that is caused by the laser moving up and down. The ribbon will eventually scratch the discs that way
I've broken the the battery holder on the PS2 fats as well. The battery is meant to go in one way. The back lid switch is finicky and sometimes it's better to just remove it and bridge the contacts together. What tends to happen is that the lid gets slightly warped overtime and doesn't put enough pressure on the back switch. Why Sony thought having two lid switches was a good idea is beyond me.
I like the PS2 slim version that you have as a donor. It can be modified to restore the IDE Interface. With quite some work it is possible to integrate an IDE TO SD Adapter and have (MicroSD) and the DVD drive internally. But I have more failed attempts on this than successful mods in this. Of course with the water damaged console nothing possible any more… Your video: Flawless as always. Wow!
I also broke my battery holder the exact same way. It caused my PS2 to stay on an infinite start-up menu everytime I turn it on 😭. Now I know how to fix it and just ordered a bunch of these battery holders.
I have the silver 79001 model and I just replaced the battery yesterday. Thankfully I was really careful about the tabs, but I can see how easy it is to break.
Had a PS2 slim years ago but we lost it in a house move. Only yesterday my old man found in his shed after cleaning it out after a flood lol. It now looks like it's been through a few wars since lmao and can bet every crevice is chock a block full of dirt and mud. I'm pretty keen to dig into it clean it all up best I can and see if she powers on still out of curiosity aha.
Very nice restoration you did, lad. Way to go. Even an All Digital PS2 mod is a great one to do even with a ThinkPad 2TB Performance PCIe Gen4 NVMe OPAL2 M.2 2280 SSD.
Very nice video! I like watching how some people are fixing up/refreshing that ol' tech gear. Not only because you are enjoying it, but also because I maybe learn a thing or two from vids like that. Glad your project went well here, enjoy your playing ;] And I'm gonna sub for your channel after that :) The only suggestion (if you want to read them ;) ): I think that when you disconnect & connect something back again, you can do a bit longer cuts (up to 1s of 1,5s) during editing process for that parts of video. I think this way it gonna go smooth with the rest of the video, which overall is pretty nice & easy going mood/setting/flow/whatever. I think these 'bit longer' cuts not gonna break whole pace of your videos. But that's just suggestion from me ;) All the best & I'm waiting for your next ones :)
This was a great cleanup. Could you have used a light oil on the fan? That's what I assumed you would use until you used the lithium grease. Again, nice work.
Oh, I've broken a battery holder in a ps3 before the battery wouldn't come out and I broke the whole holder off the board in force on accident. Luckily pads didn't get ripped. Had to solder in a new battery holder. You're not the only one.
Hi, you are very thorough with your repairs. I just bought a used slim 90001. I don't know if this model is newer or older in the PS2 line. But I certainly want my 100 dollar investment to work. Watching your video truly helps show me the way. Everything is sound. No broken doors or anything But cleaning is no doubt a possibility at least. Have you done any vids on the models with the built-in power supply? Thanks 👍👍 Could you not have just placed some hot glue on the battery edges to hold it down, or are the metal tabs the positive leads? Oh well you got it fixed 👍
i have an old ps2 slim that i was thinkin about bustin out again for old times sake...last time i tried it, the A/V cable was 'stuttering'...i was planning on takin my compressor to blow everything out, but after watching this, i might just have to do a deep clean as well.....i havent worked on consoles since the infamous 360 red ring of death/x-clamp/thermopaste fixes....and honestly, THIS looks more intimidating, LOL
with the epoxy putty (granted you might do something the same or better yet idk because I'm midway through the video) I would form it how you have to hold the post and then when it's cured sand the original plastic slightly and coat it and the putty with epoxy glue so there's something holding the two together even more so than just the bond between the joints
I’ve never heard of putting lithium grease on a fan shaft. Always been more of a fan of 3 in 1 oil. If it works, more power to you. That being said I do use lithium grease on everything else that moves, like CD/DVD/tape drive rails, worm gears, etc.
Actually one switch starts the spindle motor the other starts the laser. When the doors open both contacts are broken when it’s closed all contacts are pushed and the drive will start to run.
You need to be testing ps1 discs, ps2 cd’s, ps2 dvd, and ps2 dvd-DL. I’ve had a lot of consoles that can only read one or the other and you have to make sure it can read all of them. I have midnight club 1 as a ps2 cd and deus ex as a dvd-dl. I’m not sure of any other dvd-dl games but it’s probably important that these dual layer discs are immaculate.
I have a question about those stickers you try to preserve - are you using ipa alcohol to remove, and what do you use in terms of glue if anything to reattach? I have a Wii system sticker I want to transfer to a different case
With these fans (at least from all 79000 and 90000 PS2s I have seen), you can usually just pull off the rotor from the stator to lubricate them (and even remove dust and dirt under there). No need to remove the sticker on the back.
I'll have to give it a shot next time. It didn't seem to want to come off with average pressure and I thought I saw one of those small little snap rings under the sticker holding it in.
i have recapped all my ps2 slim models recently. seems like the video image is clearer and brighter. replaced the thermal pads with 0.5mm ones and the fan is less noisy
Indeed 0.5mm is the right thickness for the Slim and I'd preferred to have replaced mine as well, although not as critical as dried up thermal paste. I had some 1mm and 1.5mm pads on hand but not 0.5mm.
@@BorderlineOCD i used TG minus 8 1.0mm pads for my 90006 ps2. it was really hard to lift the shielding as the stock pad seems like it was glued on. after replacing the pad, the exhaust air is slightly warm and the console is barely warm. compared to older slim models which i used 0.5mm, the consoles are hot to the touch although the exhaust air is hot as well. don't know if i should use 1.0mm pads for pre 9000x consoles as well or older models just run hotter.
"I broke the battery holder" aka "YAY! I GET TO SOLDER NOW!" You don't have me fooled I see what you did there OCD.
Ha, you might just be correct. Maybe it's subconscious!
The memory card and battery clock on the fly fixes were clutch. These videos are loaded with great tips and advisory notes for console restoration.
Great to hear you found it useful. Cheers.
Please do more game consoles. This stuff is addictive and helps us all out!
Absolutely. I'm kind of addicted to working on them at this point!
You can also rebuild broken plastic bits with super glue and baking soda. It hardens and can be shaped and trimmed with files. Works really well.
With the battery holder, to reinsert a new battery properly without having to push back the spring so far, it is easiest to actually slide in the battery from the opposite side and then push it under the plastic clips. That means that you insert it from exactly the opposite side that you removed it from.
Thanks for the tip! This is how it seemed to want to go in on my aftermarket battery holder.
Yeah I thought the same, but wasn't sure enough to say anything
that is the way its supposed to be installed
put the battery in under the tabs and then it just goes in without any prying of the spring
The spring is for removal
I've never seen anybody try to install it the other way
I was so confused when he did that XDD
But i mean its a simple mistake i guess xD
Excellent job as always. Being someone that enjoys cleaning electronics, your work pleases my brain everytime. Thanks for the content as always
Thanks for watching my man, cheers.
Very nice job!
Thanks for including the part where you mistakenly broke the battery holder. It was good to see that anyone can make such mistakes. I usually bash myself way too much when I make a mistake but realized that if I stop there and think about it, I can come up with a fix rather easily.
You might be able to remove those light (black) spots/lines from the top of the PS2 by gently using a magic eraser if the plastic isn't painted. (The silver one I have seems to be painted plastic and even alcohol can damage it but I'm not sure about the white one)
The white one isn’t painted. I had one that was dropped on a front corner and used a box knife to shave off the plastic to make it more normal. It was all white plastic so that may work.
Indeed it's a matte finish similar to the black version (not silky smooth like the silver which I believe is painted). I'll give it a shot. Not sure what those marks are but they are in there pretty good.
It surprises me how that tiny little board can run all of the games released on it, some of them being quite big, while looking good. Never opened mine, and never will, this was a nice little showcase, thanks :D
Staring at my hooked up PS2 slim: we're going on an adventure!
Godspeed to you sir
You put so much love in your restoration, it's adorable.
It's a labor of love indeed my friend.
Hell yes! 2 Saturdays in a row. Really look forward to your vids. Awesome work once again.
Thanks for tuning in my man, it's very appreciated.
@@BorderlineOCD hell yea! Like I've stated previously, you got me back into the craft. So thank you.
Nice Video and Restorations,,the Door Repair and the Battery Holder replacement are new to repair, so liking the video..pls more restorations to come with errors like this that you fix...
Hell Yeah! I've retrobritened a ton of these ceramic white ntsc-js over the past couple years. They clean up super well.
Working on getting some harder to find Ps2 modchips currently, let me know if you'd like one to install and I'll send one your way :D
-Modz
Haha thanks for the offer man. So what you're really saying is you're keen to see a fail video of "how not to install a mod-chip in your PS2". That Voultar install vid on the system you sent over didn't look like a project for the faint of heart. Okay, I might be up for the challenge, although it will certainly be the most difficult project I've tackled to-date...
@@BorderlineOCD haha dude you got this! I sent Voultar a 90k model. The 79k and 90k require those super hard connections. Anything earlier then that is significantly easier. You’ll be fine 🤘🏻
Had to tear down my SCPH-77001 to lubricate the optical drive assembly, and it was surprisingly clean given how old it is. Though with the fan, I wasn't able to give it oil because it seems to be a model without a "oiling" hole. Dunce me also dropped one of the fan screws inside the heat sink, and I had a hard time trying to get it out without disassembling the whole thing, since it has a modchip installed and I don't like stressing old wires XD. At least I got it out and put it back together with a now quieter disc drive!
I loved this restoration. Ive been doing refurbishments for about a year myself and PS2 slims are by far no joke. Some of the most fragile little pieces can easily upset you. Im glad you pointed out the ribbon cable being able to scratch discs... this happened after refurbishing my Dads PS2 back in December as well as his power button having so much junk built up over 17 years that it just broke off. I had to use a donor for the power button but I did that and a couple others that also gave me a headache.
Dude you have so much patience lol
I enjoyed this video so much! Thank you!
Keep up with these restoration videos, so entertaining!
Everything, tools, spare pieces, etc. are so well ordered, organized, etc.
Thanks for the kind comments boys.
Thanks for covering a PS2 slim! You should put on the title or description what model it is, since these are so different between each other and it would help crank up the views. I for one own a SCPH-70007. I cleaned its fan but the loud whirl at startup continues, however it's quiet after that, and I noticed the unit gets rather hot while my SCPH-90001 doesn't, while its fan is much louder in return.
Also love how you dealt with the coin cell holder, magnificent.
Every video you put out makes me one step braver to attempting a capacitor replacement on my first ps3 fat my dad bought me in 2007. Your videos are so intriguing and I want to thank you C:
Out of all my consoles I've repaired, the PS3 fix is still the only thing I'm holding out on and the only one I have left to repair. It's the only one that makes me nervous.
Its an animal just to warn you. I ended up breaking one recently because I decided to clean the optical drive and theres a ribbon cable that goes underneath the power supply so I removed that power supply a good 20 times and now the system has no power. I wouldn't attempt a PS3 fat unless you are decently experienced
Your pain on the battery holder is everyone's gain! Thanks for warning us and showing us how to replace it. Be careful about that fragile part! There are much better battery holders, and this one in the PS2 Slim is not the best design. The way I did it after watching this video was bend the fragile piece back like he did and gently help the battery out. For the new battery, I bend the same piece back, and put the battery under those tiny pieces of metal and gently helped the battery in from the other side. Also, after 20 years, my PS2 Slim 77001 was still keeping date and time, but since I was in there changing out the laser, I did a major clean up and decided to change the battery as well. Surprisingly, the old battery still reads 3.1 volts! Most of the time, my ps2 is plugged in 24/7 so it barely drained the few times it was disconnected. I'll use the old battery in something that is less difficult to change like a key fob for a car.
Watching these type of videos is honestly satisfying
I have just recently started out fixing broken PS2's and found this video incredibly helpful. Thank you very much for how clearly you explained each step in the video. Great work with the memory card flap too. Great video. 👍👍
It's very gratifying to see how much care and attention went into restoring it, I loved it.
So glad i have found your channel, the way you work is so methodical and perfectionistic :)
Job well done!
That's why I love his channel, he's a man after my own heart!
Thanks for the kind comments boys.
Great restoration on that beautiful white PS2 slim! I don't see those a lot these days. Great job fixing the Memory Card door issue!
In the past when I was working on my PS2 Slim 9k, I had similar problem on the second MC door where the post just breaks off. I cringed (and swearing) seeing that happened. Not knowing the solution to fixing the post, I end up doing a case swap from a spare parts PS2 that I had laying around in my storage.
It seems the post that holds the second MC door is very fragile (a flawed design for the PS2 slims? Probably) on the PS2 slims if one is not careful when working on their console. So when I see you using a epoxy putty to create that post and testing it, I was surprised that it's possible to fix it. I think you're the first person (that I know) who actually shows a solution to fixing that problem. Now I'll be definitely going to buy epoxy putty just to do that fix if my MC door on my PS2 slim breaks off again. I wonder if it will work on the broken screw post that holds the case together....🤔
For a broken screw post I prefer the regular PlasticWeld epoxy, assuming you still have the broken post. You can cover the screw hole with some tape, epoxy it in place and drown it/wrap it in epoxy if it needs to be structural.
@@BorderlineOCD The ones on my PS2 slim are long gone however I can try that with my Guitar Hero Live controller as the screw post on one of the bottom screws has broke off (probably someone work on it before. I will try that, thanks for the tip.
Just thought I'd mention that this has inspired me - I'm currently restoring a CECHC03 and I'm now sold on the idea of respraying it white. I'm not too good at the soldering side yet but I've been painting things for years, so thanks for working on a white console haha
I looked away and I thought I was listening to Jordan Peterson refurbish a PS2
He’s my daddy, good catch. Now go clean your room! ;)
tip:
push the battery under those little ears next time and push the rest from the other side
Now we lubricrate the shaft made me giggle :)
Great work and another PS2 saved and with the battery connector we see even professionals can have badluck or seeing things over.
Wet and ready for action
@@BorderlineOCD Giggity :)
Was just working on one of my PS3 slims and ran into a situation where I was trying to change the battery, which is in a similar bracket as your PS2, and I pressed on those little tabs probably harder than I should have. Fortunately for me they didn't break but watching your made the made my hair stand on end because I realized that I was probably extremely lucky. Had they broke I wouldn't have had a replacement and would have been SOL! Though it sucked for you, I'd glad I got to see it because now I know how fragile they can be!
A fine restoration indeed, my friend! Next to the Genesis, the PS2 is my favorite console.
Found one of these for 50£ On eBay and arriving tomorrow! Love your videos and this one came just at the right time as my Slim will need some TLC as well :D
Nice restoration, out of all the slim models this is my preferred one as it's not prone to the laser ribbon scratching the disc with age - it's the only model to use clips on the bottom case to hold it down rather than adhering it to the top shield. Runs fairly cool and quiet too, especially compared to the 7000x!
I usually use 3-in-1 oil on fans, but lithium grease looks like a good solution, too. The difficult part is when you run into fans that have a tiny opening, you almost need a syringe with a needle to get it in there. Nice work on this PS2, it definitely needed some love.
I'm a fan of 3-in-1 oil and I use it often as well.
Rewatching some of your old videos. You have the best restoration content.
Seeing your master system on the shelf makes me miss mine so much, so nice to see one again. Video really makes me want to repair my ps2's issues with its disc drive.
I've been looking for a channel like this!
And now you've found it. Congratulations.
I wondered when companies started using the evil ribbon cables... One of the reasons I don't dare open up the 3ds. So easy to break these when compared to nes/snes.
What’s even worse is that the ribbon cable slowly rips when the hinges have a closing and opening cycle for 7 years.
My friends, good luck convincing eBay bots that their item is not rare.
Another educational video. Always looking forward to Saturdays to see your videos. Nice Playstation collection.
That's a quality bodge for the battery. Nice and solid. I suppose you could have also used a save battery meant for a cartridge style game but then not easily replaceable. For the fan, I normally use sewing machine oil, 321 oil, or some type of light machine oil. I'm not sure lithium grease will get liquid enough to get down there and lube things up but it sure was quiet. Maybe from just being super cleaned. Anyways, great work.
Thanks again for sending the system over, it was a fun project! You know it didn't occur to me to solder a save battery with welded on terminals, and I actually have a bunch of those for cart battery replacements albeit they are generic and I can't find any from reputable brands. Good idea though and that would have been just fine with me considering it's always easy to solder in a replacement.
The battery holder turned out great! Good job! These things happens. Congrats!
Great video! I have restored a bunch of ps2 slims over the years and I still dislike them. You did a great job with the binding post repair for the memory card door. I've use sugru in the past with similar success. Looking forward to your next video!
So satisfying to buy old hardware and make it brand new. I always clean my hardware every month to keep it brand new.
15:00 Hey! That's a 70k model! You could add the IDE-Connector! You can also attach an SD adapter/converter to that and since the drive is already gone anyway, this is a good place to position it.
It is also THE ONLY Slim PS2, which allows booting FHDB and the HDD-OSD via/through FMCB! ;)
Thanks for the tip! That particular unit might be a bit too far gone to do much with given the amount of rust but to be honest I haven't tried powering it up as it's also missing the power button board. Who knows though, maybe it can be saved. If not, I'm sure it will lend a part or two for a future repair.
This was so pleasing to watch, every single millisecond! You should be proud of your work. 👏
Glad you enjoyed it!
16:49 Also me when closing up a console that will likely never be opened again. I'm a new viewer but I love that I already got my answer as to why your channel is named what it is haha
This video made me wanna sub, can't wait for all the great videos to come!
Always remember to test both CD and DVD based games. Laser power can be adjusted independently for each type of disc.
Not all hero wear capes, thank you Sir
For a quicker job on plastic repairs, try the super glue and baking soda method. It can be sanded, filed, etc afterwards. You have to have the runny super glue though, I've tried it with gel to no luck. I've fixed broken clip tabs, standoff holders, screw posts, flip down doors on old CRT monitors, etc and just to be on the safe side, you can even hit the job with activator spray after to ensure an instant cure.
LOVE your videos! Honestly the console repairs are so soothing and help with my anxiety. Please do more of these 🔥💕
PS2 is the shit!! Love it forever!
Borderline, make sure to adjust the ribbon cable for the laser. It can get up after some time, that is caused by the laser moving up and down. The ribbon will eventually scratch the discs that way
your work is always so professional and clean-looking -- love watching you work on these consoles!
The yt algorythm got me here , not dissapoimted, subbed
Thanks for the sub.
@@BorderlineOCD it was well deserved, can't wait for future uploads 🥰🥰
I'm OCD, as well. And, I thoroughly enjoy your videos.
I've broken the the battery holder on the PS2 fats as well. The battery is meant to go in one way. The back lid switch is finicky and sometimes it's better to just remove it and bridge the contacts together. What tends to happen is that the lid gets slightly warped overtime and doesn't put enough pressure on the back switch. Why Sony thought having two lid switches was a good idea is beyond me.
I like the PS2 slim version that you have as a donor. It can be modified to restore the IDE Interface. With quite some work it is possible to integrate an IDE TO SD Adapter and have (MicroSD) and the DVD drive internally. But I have more failed attempts on this than successful mods in this.
Of course with the water damaged console nothing possible any more…
Your video: Flawless as always. Wow!
This is so satisfying to watch.
I also broke my battery holder the exact same way. It caused my PS2 to stay on an infinite start-up menu everytime I turn it on 😭. Now I know how to fix it and just ordered a bunch of these battery holders.
I have the silver 79001 model and I just replaced the battery yesterday. Thankfully I was really careful about the tabs, but I can see how easy it is to break.
Hola, buen trabajo.
Es recomendable cambiar el thermal pad del procesador?
Gracias
I have great memories of working on PS2 at Sony back in the day.
Had a PS2 slim years ago but we lost it in a house move.
Only yesterday my old man found in his shed after cleaning it out after a flood lol.
It now looks like it's been through a few wars since lmao and can bet every crevice is chock a block full of dirt and mud.
I'm pretty keen to dig into it clean it all up best I can and see if she powers on still out of curiosity aha.
Very nice restoration you did, lad. Way to go. Even an All Digital PS2 mod is a great one to do even with a ThinkPad 2TB Performance PCIe Gen4 NVMe OPAL2 M.2 2280 SSD.
Very nice video! I like watching how some people are fixing up/refreshing that ol' tech gear. Not only because you are enjoying it, but also because I maybe learn a thing or two from vids like that.
Glad your project went well here, enjoy your playing ;]
And I'm gonna sub for your channel after that :)
The only suggestion (if you want to read them ;) ):
I think that when you disconnect & connect something back again, you can do a bit longer cuts (up to 1s of 1,5s) during editing process for that parts of video. I think this way it gonna go smooth with the rest of the video, which overall is pretty nice & easy going mood/setting/flow/whatever.
I think these 'bit longer' cuts not gonna break whole pace of your videos.
But that's just suggestion from me ;)
All the best & I'm waiting for your next ones :)
Thanks buddy. Glad you enjoyed the video.
My favorite console, love your content
Luckily no bugs in there. Ya I have that same ps2 slim, those things r pretty tank with holding up and continuing to work
This was a great cleanup. Could you have used a light oil on the fan? That's what I assumed you would use until you used the lithium grease. Again, nice work.
Certainly. 3-in-1 oil is good and what I often use as well.
@@BorderlineOCD Thank you.
Love Borderline OCD you have Ps1/PS2/and PS3 all in one area now all you need is a PS4 and a PS5 if you can find them at a reasonable price
Oh, I've broken a battery holder in a ps3 before the battery wouldn't come out and I broke the whole holder off the board in force on accident. Luckily pads didn't get ripped. Had to solder in a new battery holder. You're not the only one.
That was the later system, the original didn't have a battery like that. It was with a ribbon, so it wasn't simple to replace it.
Hi, you are very thorough with your repairs. I just bought a used slim 90001. I don't know if this model is newer or older in the PS2 line. But I certainly want my 100 dollar investment to work. Watching your video truly helps show me the way. Everything is sound. No broken doors or anything
But cleaning is no doubt a possibility at least. Have you done any vids on the models with the built-in power supply?
Thanks 👍👍
Could you not have just placed some hot glue on the battery edges to hold it down, or are the metal tabs the positive leads?
Oh well you got it fixed 👍
your videos are therapeutic
If you don't have specific putty to fix plastics you can use the super glue baking soda trick. Tech tangents has a great video about it.
Nice fix, very interesting video and a really nice fix with the epoxy
The battery holder on my PS 2 Slim did brake as well but my repair was anything but elegant
Going through the old videos looking for inspiration 🏆
i have an old ps2 slim that i was thinkin about bustin out again for old times sake...last time i tried it, the A/V cable was 'stuttering'...i was planning on takin my compressor to blow everything out, but after watching this, i might just have to do a deep clean as well.....i havent worked on consoles since the infamous 360 red ring of death/x-clamp/thermopaste fixes....and honestly, THIS looks more intimidating, LOL
Buy an ultrasonic cleaner. They are not cheap, but really worth it! I cleaned all my Gameboys that way, no scrubbing!
Great video! How funny that I was just on eBay looking to buy the Hit and Run game 😵💫
with the epoxy putty (granted you might do something the same or better yet idk because I'm midway through the video) I would form it how you have to hold the post and then when it's cured sand the original plastic slightly and coat it and the putty with epoxy glue so there's something holding the two together even more so than just the bond between the joints
An additional thing I'd suggest is using a "magic eraser" to get the pen parks from the lid :)
Really beautiful restoration. Thanks for your videos, i always learn something from you.
Thank you very much!
You are the Louis Rosmann of video game consoles!
I’ve never heard of putting lithium grease on a fan shaft. Always been more of a fan of 3 in 1 oil. If it works, more power to you. That being said I do use lithium grease on everything else that moves, like CD/DVD/tape drive rails, worm gears, etc.
Actually one switch starts the spindle motor the other starts the laser. When the doors open both contacts are broken when it’s closed all contacts are pushed and the drive will start to run.
Used to have this but in red. Someone broke into my house and this is one of the things they took. Maybe would try to hunt for one later on
new borderline OCD upload lets goo
GREAT job Dude 👍
Más restauraciónes de consolas por favor, excelente trabajo.
Great Video very detailed 👌
You need to be testing ps1 discs, ps2 cd’s, ps2 dvd, and ps2 dvd-DL. I’ve had a lot of consoles that can only read one or the other and you have to make sure it can read all of them.
I have midnight club 1 as a ps2 cd and deus ex as a dvd-dl. I’m not sure of any other dvd-dl games but it’s probably important that these dual layer discs are immaculate.
Why isn’t there thermal paste?
I have a question about those stickers you try to preserve - are you using ipa alcohol to remove, and what do you use in terms of glue if anything to reattach? I have a Wii system sticker I want to transfer to a different case
Yep just IPA and a plastic razor. It's a bit finicky so maybe practice on a sticker you don't care about first.
Nice work. Great looking system :)
With these fans (at least from all 79000 and 90000 PS2s I have seen), you can usually just pull off the rotor from the stator to lubricate them (and even remove dust and dirt under there). No need to remove the sticker on the back.
I'll have to give it a shot next time. It didn't seem to want to come off with average pressure and I thought I saw one of those small little snap rings under the sticker holding it in.
I'd drop the "borderline" 😂 Super clean! Love the attention to detail.
8:25 will do, thanks!
21:26 Good Job!!!
Great content. It might be a few more years but I have some old PS2's I would like to clean up like new as well as a noisy xbox 360.
I haven’t used my ps2 is like 10 years 👀
Always had a door problem, I would have to put a book on the lid
i have recapped all my ps2 slim models recently. seems like the video image is clearer and brighter. replaced the thermal pads with 0.5mm ones and the fan is less noisy
Indeed 0.5mm is the right thickness for the Slim and I'd preferred to have replaced mine as well, although not as critical as dried up thermal paste. I had some 1mm and 1.5mm pads on hand but not 0.5mm.
@@BorderlineOCD i used TG minus 8 1.0mm pads for my 90006 ps2. it was really hard to lift the shielding as the stock pad seems like it was glued on. after replacing the pad, the exhaust air is slightly warm and the console is barely warm. compared to older slim models which i used 0.5mm, the consoles are hot to the touch although the exhaust air is hot as well. don't know if i should use 1.0mm pads for pre 9000x consoles as well or older models just run hotter.