I was happy to gain the information from the video but am really impressed with how you answer questions in the comments. Thank you for sharing all the knowledge.
You got a subscribe cuz you answered every question, that’s pretty awesome and I never seen that before. Mine got the red triangle of death as some other dude said in a video, and the engine light game on. It is brand new with 101.6 hours on it. It got scared of your video and the AC is working now. For your added knowledge, some other video showed a fuse blown and fixed theirs. Anyhow, I’m a zombie from trying to figure it and headed to dream land. Keep up the good work.
The apu in the video actually has 26,294 hours on it now and is only supposed to run only 10k hours before a rebuild. It starts up first try and runs like new. With proper maintenance they can surpass most expirations
i have the same apu run for 5 to 10 minutes and shut down that connection on the 50 volts fuse look ok the alternator is pushing 13.9 volts, i just did apm with om parts and still doing that all fuses are good fans both working good, you have idea what else could be?
Hello, thank you so much for the video. I am having some issues with mine. The heat works fine. Ac is having issues. The second the compressor clutch kicks, the belt stops unit dies. I can't figure what is going on. I will be glad if you can help. Thank you so much
Check and see if the compressor is locked up. Do that by making sure the kill switch is in the stop position. Then using yout hand try to turn the center of the compressor clutch. Do not try to turn tge pully just the center of the pully. If you can't turn it then your a/c compressor is locked up and needs replaced.
Good day, great video tutorial my friend. Have a question, mine is not blowing cold air, I checked voltage at the compressor connector and got only 7 volts, doesn’t it supposed to get 12? Also check pressure on gas and is ok, any advice will be much appreciated, thanks, blessings.
Check ya engine mounts mine were blown out and shaking the alternator bracket bolt clean out... seems like you had the same problem.. makes more sense then people not putting it back in
for the last two weeks ive been trying to get my apu running I'm getting negative amps and the service tool also says app switch off and hmco open what could cause this ive been trying everything watching this I'm thinking I might have a bare wire on my ac comp would that cause all my problems thanks for any info ..
Thank you. I learned by tinkering with them. Mostly I apply what I know about cars to figuring out the problem. I have other videos on thermoking as well.
This is an old video and I hope you can help me out.... me inverter is reading 15.4v obviously it's overcharging the whole system. The apu unit runs fine everything works i replaced the alternator about a year ago and never really used the inverter because it would just keep beeping i figured it was a dead inverter so just recently I bought a new one....replaced it and noticed the high voltage reading so I disconnect the new one and hook up the old one and same thing so I know it's not the inverter or the alternator since it's fairly new and it seems to be working fine... another quick note if I turn on all the lights on the truck and trailer it will read a lower voltage and inverter works fine... any ideas....?
Sorry I missed this! You need to pressurize it and add a dye test freon can to it and look for the leak. Normally it's in a line and a broken "o" ring seal. You probably already know this and I'm sorry for missing this question! I have been going through a lot and currently I'm not capable of making videos or working on these units or anything. I'm still working on being able to walk I had a dramatic back injury so I have been absent from making videos on apu's for some time.
Yup. Look at your fuel lines the main line goes into a canister with what looks like a oil filter. That's the fuel/ water sepperator. 2 lines will come out of that and go to the right. The far right line is your main supply line. Loosen that and try to crank it. Keep resetting and cranking till you get a flow of fuel out of it then snug the line up and it should start.
@@hillbillyholler516 Hi, I overfill oil on top fill of the apu by mistake, now its cranck but wont start, I draneid oil and need to change the oil filter, can you give me a help here, because I think oil may have gone to the cylinders...
Do you have any advice on tension of the belt? I seen one video suggest that tension is good if you can turn the belt to 90 deg in the middle of the longest run (or where the belt runs the longest distance between two pulleys). I got an ac comp that doesnt seem to be disengaging the clutch. Im going to try pb blast the ac pulley/clutch connection to see if rust has locked them together. Any thoughts if that isnt the problem?
Zero Fayt in my video i talk about the wire that goes to the ac clutch and a short it had in it. Now if you have a fault that is keeping constant power going to that wire it will keep the clutch engauged at all times. With the unit off try to spin the cente of the ac clutch. It should spin without turning the outter pully. If it dont then the clutch may be getting constant power or the clutch is sezed up. To see if its getting constant power clip the wire in a spot that will be easy to splice back. If it still wont spin its a bad clutch. As for belt tension you want about 3/4" of deflection when you apply about 20 pounds of force.in your belt once its tight. Try hitting the outside kill switch before clipping the power wire to the clutch. Either way its most likely going to need a shop unless its a bad clutch and you know how to replace one.
Not sure how old this is, but I recently changed the alternator and ground wire and I am still getting the alt code. I just replaced the belt. What else should I look for. I have about 20000 hrs on the unit.
I checked those already and they are all good. I spoke with one of the TK dealers and he mentioned something about checking the 2 pin plug that plugs into the back of the alternator to make sure that both pins are energized with at least 12v while the apu is running. Have you heard of this before?
@@anthonykguru yes I have. With an alternator that has an internal regulator if you don't have power going into the plug you mentioned it won't open up the regulator to start charging. The internal regulator reads the battery voltage and keeps the alternator from over charging the battery. Also another thing to look at is ground. An alternator will not charge if it's lost it's ground usually due to corrosion so you may also try adding another ground wire to the casing or mount.
Hello,I'm getting alt code and when I was looking for something I found out that ac compressor clutch stops and belt just keeps going running and smells, what should I do,plz advise
@@JB-nm6uk if the unit is running and the a/ c compressor stops spinning and the belt is still going with the compressor clutch not spinning then yes it is time to replace the compressor. Cost depends on the shop and if they have a generic compressor in stock.
@@JB-nm6uk before you replace anything I would first check the tension on your belt. If the belt is loose it will slip when the a/c compressor kicks in as well
@@hillbillyholler516 I checked the belt it seems pretty tight, the very first I had this problem was after an oil change, it was running fine all the sudden it stopped throwing cold air I reset it and worked good for a week and threw a alt code and stopped
Good question. Well all thermoking apu'e are designed to have a relay that runs through the ignition so when the truck ignition is on the apu will not run. To change this you will have to rewire the apu so no ignition signal from the ignition switch reaches the apu. Its actually not worth the cost/ and time because expense will over ride repair cost. Also if you are experiencing truck a/c issues your compressor may be going bad and It will take out your main serpentine belt and shut your engine down. Most times if your truck a/c Is acting up it means your a/c clutch is going out so when it does fail it will lock up and burn up your serpentine belt which runs your engine accesories. So your water pump and alternator will not run once it fully seizes. If you run reefer you can use jumper cables to charge your truck to limp to a shop but you will be lacking a cooling system so you will be limited on your milage range most likely a 50 mile range depending on the weight, temperature and what engine you have. But if your truck a/c is failing you should go to a shop because the compressor is part of your main serpentine belt pullies and if one fails all fail soon after
If its low on freon then you have a leak. First I would lift the bunk and check the condenser coils and make sure they are clean and clear of obstructions. If they are clear then check your freon pressure. If it's too low your compressor clutch wont kick in. If the pressure is high the compressor is bad. If the pressure is ok but the clutch isn't working then you have a bad compressor clutch
I haven't seen one share coolant to the engine except a rigmaster. The tgermoking units have a radiator cap. Here is a tip. When it's really hot, and your unit keeps shutting down try opening the hood for more air flow. It helps a lot. The cap should be located on the outside of the casing on the side towards the cab. Do not open it when it's hot! If you have a thermoking use dex cool 50/50 mix or 100% antifreeze mixed with with distilled water. Never use tap water in a cooling system.
My inverter (thermo - king ) model showed code e03, then started beeping , after that , my control panel said ALT, I turned the master switch on and off, and the inverter on and off , and it's been ok now for several hours, I hve new batteries that are 2 months old , any suggestions at to what my hve caused this, I just spent $1000 plus dollars to get it serviced at thermo king less then a week ago . Could my inverter be bad ..? THX in advance .
rrios283s73 the e03 code is a overcharge code or your inverter Wes receiving too many amps in excess of 15.5 volts. It could have due to a stuck voltage regulator or if you had your truck hooked up to a charger recently. Another cause is running more then one cooking appliance at a time causing a voltage deficit and when the system catches up it overcharged. On rare occasions clogged vent fans on your inverter can make it throw an overcharge code. So I would blow out your 2 vent fans located on the bottom and the 2 on the back and make sure they are clear. In the off chance your inverter is actually going out you can purchase a replacement on amazon for 1/3 of what thermo king charges and install it in 20 min or less.
Hey bro, so my apu was working good last year, today i tried turning it on today and it runs for about 20 seconds and then it shuts off, its giving me code ACS, i checked all fuses and all are good, please help i dont have the cash to take it to thermoking, thanks
That's a low freon code bro. Look on the back of your truck passenger side, and locate the black canister. Unplug the sensor there, and make sure it's not damaged. If it's ok then you need to add freon to your system. It takes 35# unless you are in 100 degree wether then its 40# of freon. If you read high when its running then your compressor is bad, and it's not pulling the pressure down. Another thing to check is the wires oh your compressor clutch that run through the housing on the compressor to the clutch. Make sure they aren't chafed and have exposed wire.
@@renezepeda956 ok well if I have time tomorrow weather allowing I will do my best to make a video on the ignition wiring on an older tk unit. It's supposed to rain but hopefully I can find a dry time to do it. Sorry I don't have as much time as I would like to devote to my channel due to a new job but I will definitely try to help you given my time constraints. If I can make a starter wiring video I will link it here so it's easy for you to find. It's a shame that they the shops seem to try to keep information on these units private so repairs almost always have to be done in shops. I will help you if I can. I have your email and will try to get you some help in the morning.
Jose Morales grab the center of your compressor clutch when its not running of course and try to spin the centrer by hand. You should be able to turn it. If it wont turn then your compressor is locked up. High freon pressure usually means a bad compressor. The compressor moves the freon and will reduice the pressure in the lines to about 35 psi. If its showing red you have way too much freon pressure and if its locking up the belt when the clutch kicks in then either the compressor is locked up or it is way overcharged which is causing your compressor to seize
Red alarm?.....I am going to need more details. What unit do you have? What are the codes? Does the unit do,? Does it fire up fast? How does it start? Starts first try? What setting? Is it set for heat or a/c
it means it has an active alarm in one or more of the systems and possibly will shut down some or all of the systems. I'm not familiar with the newer models so look in your owners manual on how to check the code. my guess it is in the compressor system most likely a sensor or if you had been running it already and just got the code your evaporator coil could be iced up
tolivercarlton if you can pull the code i will try to help you figure it out. Eng. codes are engine related..... alt means it's in the charging system and act is in the a/c system
Highly competitive environment extremely underpaid office did not respect what you do on the mechanics floor president of the company love the salesman treated the mechanics like they were second-class people. I was a first-year tech was expected to perform like a journeyman I had to get a second job because I couldn't make enough money at this job when I got that second job had to quit cuz they considered it a conflict of interest the whole experience reminded me of the movie Hunger Games when the service manager fired me I was so happy I remember saying to him that's the best news I could have heard all day you should have seen the look on his face he was shocked
Jon Minnella i knew tk was messed up but didnt know it was that bad! I had issues with them charging a diagnosis fee for obvious issues that i pointed out to them. For instance they charged me a $160 diagnosis fee when i took it in for a waterpump and i even told them what was wrong and showed them it was a seized waterpump. I didnt pay the fee of course and was asked never to come back to their shop. If i had the part i would have done it myself. Tk acts like any repair information if top secret and you can find very little about their stuff on how to fix it. I also found out most of their shops suck and you usually have to go in several times for them to fix it right. ( except nashville tn. and springfield mo. they do good work) Its a shame bc they make a great unit but service on apu's needs an upgrade
The Hillbilly Laboratory well that sounds about right its all happing becouse of the highly competitive work environment i was so stressed when i worked there and always worried about getting fired after 7th month i started giving them a hard time back didn't think i would welcome being fired but boy im telling you i was over joyed when service manger gave me the news
Jon Minnella my last job was like that. All stress and drama plus working 6-7 days a week 14-16 hour days. I was sooooo happy to leave that hell hole! I was the operations manager and my reigonal manager short handed me and had me running my market plus 2 other markets. He always found a way to mess up my vacation plans. I had enough when they finally hired me an assistant and i found out he was making 14k more a year than i was and had no logistics experiance.
My apu won’t even crank
And as u said I check the wiring to the switch
And it start right up
Thank you for sharing the great info
Glad I could help! They act like any Apu info is top secret
I was happy to gain the information from the video but am really impressed with how you answer questions in the comments. Thank you for sharing all the knowledge.
G G you are welcome!
I should have another tk and wabasto video ready some time Friday
Hillbilly Holler Looking forward to it.
Hey thanks for the video, I am giving my recon Tripac it's first service and this does help.
You got a subscribe cuz you answered every question, that’s pretty awesome and I never seen that before. Mine got the red triangle of death as some other dude said in a video, and the engine light game on. It is brand new with 101.6 hours on it. It got scared of your video and the AC is working now. For your added knowledge, some other video showed a fuse blown and fixed theirs. Anyhow, I’m a zombie from trying to figure it and headed to dream land. Keep up the good work.
The apu in the video actually has 26,294 hours on it now and is only supposed to run only 10k hours before a rebuild.
It starts up first try and runs like new.
With proper maintenance they can surpass most expirations
i have the same apu run for 5 to 10 minutes and shut down that connection on the 50 volts fuse look ok the alternator is pushing 13.9 volts, i just did apm with om parts and still doing that all fuses are good fans both working good, you have idea what else could be?
I have the same problem😮😢
Hello, thank you so much for the video. I am having some issues with mine. The heat works fine. Ac is having issues. The second the compressor clutch kicks, the belt stops unit dies. I can't figure what is going on. I will be glad if you can help. Thank you so much
Check and see if the compressor is locked up.
Do that by making sure the kill switch is in the stop position.
Then using yout hand try to turn the center of the compressor clutch.
Do not try to turn tge pully just the center of the pully.
If you can't turn it then your a/c compressor is locked up and needs replaced.
Good day, great video tutorial my friend. Have a question, mine is not blowing cold air, I checked voltage at the compressor connector and got only 7 volts, doesn’t it supposed to get 12? Also check pressure on gas and is ok, any advice will be much appreciated, thanks, blessings.
Check ya engine mounts mine were blown out and shaking the alternator bracket bolt clean out... seems like you had the same problem.. makes more sense then people not putting it back in
for the last two weeks ive been trying to get my apu running I'm getting negative amps and the service tool also says app switch off and hmco open what could cause this ive been trying everything watching this I'm thinking I might have a bare wire on my ac comp would that cause all my problems thanks for any info ..
I work on these daily for a thermo king dealer and you know more then most of our techs.
Thank you. I learned by tinkering with them. Mostly I apply what I know about cars to figuring out the problem.
I have other videos on thermoking as well.
You mean they aren't worth 150 bucks an hour ? Lol
That’s sad
Mannnn my apu is throwing a acs code where can I start ?
Green valve sensor ?
Thank you for the awesome video it helped a great deal
I'm glad I could help!
Great video. one question where do the two Grey wires on the atl connect ?
This is an old video and I hope you can help me out.... me inverter is reading 15.4v obviously it's overcharging the whole system. The apu unit runs fine everything works i replaced the alternator about a year ago and never really used the inverter because it would just keep beeping i figured it was a dead inverter so just recently I bought a new one....replaced it and noticed the high voltage reading so I disconnect the new one and hook up the old one and same thing so I know it's not the inverter or the alternator since it's fairly new and it seems to be working fine... another quick note if I turn on all the lights on the truck and trailer it will read a lower voltage and inverter works fine... any ideas....?
I have a leak somewhere but I can’t seem to find it. Any common areas that are prone to leaking? If I charge it up it usually holds for a few hours.
Sorry I missed this!
You need to pressurize it and add a dye test freon can to it and look for the leak.
Normally it's in a line and a broken "o" ring seal.
You probably already know this and I'm sorry for missing this question!
I have been going through a lot and currently I'm not capable of making videos or working on these units or anything.
I'm still working on being able to walk I had a dramatic back injury so I have been absent from making videos on apu's for some time.
Thank You for your knowledge very informative!
Cool video. Wish you'd record landscape instead of portrait mode.
Little Fella Trucking lol. Yeah i relized that after i recorded it.
Im not very phone literate
Thank u for the video
Hi. Do you know how to prime/crank the unit manually? We changed the fuel filter and now the unit try to start but fails. Thanks in advance
Yup. Look at your fuel lines the main line goes into a canister with what looks like a oil filter.
That's the fuel/ water sepperator.
2 lines will come out of that and go to the right.
The far right line is your main supply line.
Loosen that and try to crank it.
Keep resetting and cranking till you get a flow of fuel out of it then snug the line up and it should start.
@@hillbillyholler516 Hi, I overfill oil on top fill of the apu by mistake, now its cranck but wont start, I draneid oil and need to change the oil filter, can you give me a help here, because I think oil may have gone to the cylinders...
@@joaobalula3984 after you refilled the oil will it turn over when the starter is engauged?
Do you have any advice on tension of the belt? I seen one video suggest that tension is good if you can turn the belt to 90 deg in the middle of the longest run (or where the belt runs the longest distance between two pulleys). I got an ac comp that doesnt seem to be disengaging the clutch. Im going to try pb blast the ac pulley/clutch connection to see if rust has locked them together. Any thoughts if that isnt the problem?
Zero Fayt in my video i talk about the wire that goes to the ac clutch and a short it had in it.
Now if you have a fault that is keeping constant power going to that wire it will keep the clutch engauged at all times.
With the unit off try to spin the cente of the ac clutch.
It should spin without turning the outter pully.
If it dont then the clutch may be getting constant power or the clutch is sezed up.
To see if its getting constant power clip the wire in a spot that will be easy to splice back.
If it still wont spin its a bad clutch.
As for belt tension you want about 3/4" of deflection when you apply about 20 pounds of force.in your belt once its tight.
Try hitting the outside kill switch before clipping the power wire to the clutch.
Either way its most likely going to need a shop unless its a bad clutch and you know how to replace one.
Not sure how old this is, but I recently changed the alternator and ground wire and I am still getting the alt code. I just replaced the belt. What else should I look for. I have about 20000 hrs on the unit.
I would check the fuze blocks on your batteries and the under bunk fuzes
I checked those already and they are all good. I spoke with one of the TK dealers and he mentioned something about checking the 2 pin plug that plugs into the back of the alternator to make sure that both pins are energized with at least 12v while the apu is running. Have you heard of this before?
@@anthonykguru yes I have.
With an alternator that has an internal regulator if you don't have power going into the plug you mentioned it won't open up the regulator to start charging.
The internal regulator reads the battery voltage and keeps the alternator from over charging the battery.
Also another thing to look at is ground.
An alternator will not charge if it's lost it's ground usually due to corrosion so you may also try adding another ground wire to the casing or mount.
Hello,I'm getting alt code and when I was looking for something I found out that ac compressor clutch stops and belt just keeps going running and smells, what should I do,plz advise
Sounds like your a/c compressor is wore out and is trying to lock up
@@hillbillyholler516really appreciate ur feedback, should I change the compressor, any idea how expensive that would be ,
@@JB-nm6uk if the unit is running and the a/ c compressor stops spinning and the belt is still going with the compressor clutch not spinning then yes it is time to replace the compressor.
Cost depends on the shop and if they have a generic compressor in stock.
@@JB-nm6uk before you replace anything I would first check the tension on your belt.
If the belt is loose it will slip when the a/c compressor kicks in as well
@@hillbillyholler516 I checked the belt it seems pretty tight, the very first I had this problem was after an oil change, it was running fine all the sudden it stopped throwing cold air I reset it and worked good for a week and threw a alt code and stopped
Looks like I have the same apu. My air conditioning not working how can I run the apu while truck is running
Good question.
Well all thermoking apu'e are designed to have a relay that runs through the ignition so when the truck ignition is on the apu will not run.
To change this you will have to rewire the apu so no ignition signal from the ignition switch reaches the apu.
Its actually not worth the cost/ and time because expense will over ride repair cost.
Also if you are experiencing truck a/c issues your compressor may be going bad and It will take out your main serpentine belt and shut your engine down.
Most times if your truck a/c Is acting up it means your a/c clutch is going out so when it does fail it will lock up and burn up your serpentine belt which runs your engine accesories.
So your water pump and alternator will not run once it fully seizes.
If you run reefer you can use jumper cables to charge your truck to limp to a shop but you will be lacking a cooling system so you will be limited on your milage range most likely a 50 mile range depending on the weight, temperature and what engine you have.
But if your truck a/c is failing you should go to a shop because the compressor is part of your main serpentine belt pullies and if one fails all fail soon after
Thanks bro for the good info 👍🏻
You are welcome!
I turn ac on no cold air any troubleshooting if need recharge free on or bad wire .
Thanks awesome video information
If its low on freon then you have a leak.
First I would lift the bunk and check the condenser coils and make sure they are clean and clear of obstructions.
If they are clear then check your freon pressure.
If it's too low your compressor clutch wont kick in.
If the pressure is high the compressor is bad.
If the pressure is ok but the clutch isn't working then you have a bad compressor clutch
Thanks for the quick feedback I really appreciate your knowledge
How can i add Coolant to the apu or does it share from the Engine?
I haven't seen one share coolant to the engine except a rigmaster.
The tgermoking units have a radiator cap.
Here is a tip.
When it's really hot, and your unit keeps shutting down try opening the hood for more air flow.
It helps a lot.
The cap should be located on the outside of the casing on the side towards the cab.
Do not open it when it's hot!
If you have a thermoking use dex cool 50/50 mix or 100% antifreeze mixed with with distilled water.
Never use tap water in a cooling system.
Thanks for info
My inverter (thermo - king ) model showed code e03, then started beeping , after that , my control panel said ALT, I turned the master switch on and off, and the inverter on and off , and it's been ok now for several hours, I hve new batteries that are 2 months old , any suggestions at to what my hve caused this, I just spent $1000 plus dollars to get it serviced at thermo king less then a week ago .
Could my inverter be bad ..?
THX in advance .
rrios283s73 the e03 code is a overcharge code or your inverter Wes receiving too many amps in excess of 15.5 volts.
It could have due to a stuck voltage regulator or if you had your truck hooked up to a charger recently.
Another cause is running more then one cooking appliance at a time causing a voltage deficit and when the system catches up it overcharged.
On rare occasions clogged vent fans on your inverter can make it throw an overcharge code.
So I would blow out your 2 vent fans located on the bottom and the 2 on the back and make sure they are clear.
In the off chance your inverter is actually going out you can purchase a replacement on amazon for 1/3 of what thermo king charges and install it in 20 min or less.
Hey bro, so my apu was working good last year, today i tried turning it on today and it runs for about 20 seconds and then it shuts off, its giving me code ACS, i checked all fuses and all are good, please help i dont have the cash to take it to thermoking, thanks
That's a low freon code bro.
Look on the back of your truck passenger side, and locate the black canister.
Unplug the sensor there, and make sure it's not damaged.
If it's ok then you need to add freon to your system.
It takes 35# unless you are in 100 degree wether then its 40# of freon.
If you read high when its running then your compressor is bad, and it's not pulling the pressure down.
Another thing to check is the wires oh your compressor clutch that run through the housing on the compressor to the clutch.
Make sure they aren't chafed and have exposed wire.
Thank u bro!!
great blog tks
Listen to your Bigfoot stories wow really good
Can u send a pic of the wires that go to the starter need to know how to put back the starter weres
I will need your email address to send it to
Renezepeda364@gmail.com
I want to see where the wire go I would really appreciate it driver thanks
Sorry wrong email it renezepeda363@gmail.com
@@renezepeda956 ok well if I have time tomorrow weather allowing I will do my best to make a video on the ignition wiring on an older tk unit.
It's supposed to rain but hopefully I can find a dry time to do it.
Sorry I don't have as much time as I would like to devote to my channel due to a new job but I will definitely try to help you given my time constraints.
If I can make a starter wiring video I will link it here so it's easy for you to find.
It's a shame that they the shops seem to try to keep information on these units private so repairs almost always have to be done in shops.
I will help you if I can.
I have your email and will try to get you some help in the morning.
My apu stoped blowing cold air, tried recharging but gage goes red, just noticed my belt stops turning! What do u guys think the problem is thanks
Jose Morales grab the center of your compressor clutch when its not running of course and try to spin the centrer by hand.
You should be able to turn it.
If it wont turn then your compressor is locked up.
High freon pressure usually means a bad compressor.
The compressor moves the freon and will reduice the pressure in the lines to about 35 psi.
If its showing red you have way too much freon pressure and if its locking up the belt when the clutch kicks in then either the compressor is locked up or it is way overcharged which is causing your compressor to seize
I am having the same problem. I tried turning the clutch with my fingers, but it would not turn freely
Im getting the red alarm and the alt come up and it runs for a lil while and cut off
Red alarm?.....I am going to need more details.
What unit do you have?
What are the codes?
Does the unit do,?
Does it fire up fast?
How does it start?
Starts first try?
What setting?
Is it set for heat or a/c
Is there any way you can pull up a specific alarm code?
Its starts up and goes to charge and it does stay running and it is the tripac evolution and it does the same for the fan and heat
what does it mean when the yellow triangle comes on?
an it is not blowing cold air
it means it has an active alarm in one or more of the systems and possibly will shut down some or all of the systems.
I'm not familiar with the newer models so look in your owners manual on how to check the code.
my guess it is in the compressor system most likely a sensor or if you had been running it already and just got the code your evaporator coil could be iced up
tolivercarlton if you can pull the code i will try to help you figure it out.
Eng. codes are engine related..... alt means it's in the charging system and act is in the a/c system
👍
My tk doesn't start and it showed code 62, which is ammeter out of calibration. Could someone explain me what I have to do to repair it and how?
Miguel Lara ok when you try to start it does it crank then give the code or does it go straight to the code when you try to start it?
Hillbilly Holler it goes straight to the code, I tried to start and it cranked
Miguel Lara posting a video.response now
Miguel Lara ruclips.net/video/09lIb9Mc28M/видео.html
Hillbilly Holler thanks
Thank u
Jose Morales no worries i hope it helped and you can get it fixed pretty cheap
I worked at tk for 9 mounths terrible experience
Jon Minnella what happened?
Highly competitive environment extremely underpaid office did not respect what you do on the mechanics floor president of the company love the salesman treated the mechanics like they were second-class people. I was a first-year tech was expected to perform like a journeyman I had to get a second job because I couldn't make enough money at this job when I got that second job had to quit cuz they considered it a conflict of interest the whole experience reminded me of the movie Hunger Games when the service manager fired me I was so happy I remember saying to him that's the best news I could have heard all day you should have seen the look on his face he was shocked
Jon Minnella i knew tk was messed up but didnt know it was that bad!
I had issues with them charging a diagnosis fee for obvious issues that i pointed out to them.
For instance they charged me a $160 diagnosis fee when i took it in for a waterpump and i even told them what was wrong and showed them it was a seized waterpump.
I didnt pay the fee of course and was asked never to come back to their shop.
If i had the part i would have done it myself.
Tk acts like any repair information if top secret and you can find very little about their stuff on how to fix it.
I also found out most of their shops suck and you usually have to go in several times for them to fix it right. ( except nashville tn. and springfield mo. they do good work)
Its a shame bc they make a great unit but service on apu's needs an upgrade
The Hillbilly Laboratory well that sounds about right its all happing becouse of the highly competitive work environment i was so stressed when i worked there and always worried about getting fired after 7th month i started giving them a hard time back didn't think i would welcome being fired but boy im telling you i was over joyed when service manger gave me the news
Jon Minnella my last job was like that.
All stress and drama plus working 6-7 days a week 14-16 hour days.
I was sooooo happy to leave that hell hole!
I was the operations manager and my reigonal manager short handed me and had me running my market plus 2 other markets.
He always found a way to mess up my vacation plans.
I had enough when they finally hired me an assistant and i found out he was making 14k more a year than i was and had no logistics experiance.