Bhai thank you so much main bahut pareahan tha bhai mujhe koi video mil hi nhi rahi thi or jo mil rahi thi unke connection alag they so thank you so much ❤️❤️ Bhai
4440 ic board is not that powerful. It consumes Only 12 volts not even 12-0-12.. U can get 40 watts at 4 ohms load..each channel... It has 2 channels...
Humming ka one of the main reasons hota hai grounding.. agar humming aye to earth line ko heat sink ke sath jor dijiye.. Iss board me per channel 14 watts karke milta hai 4 ohms ke load pe.. Agar aap 1A use kar rahe hai to 6 watts ke speaker ko use kar sakte hai.. or agar 2 ya 3 A use kar rahe hai to 14 watts ke upar ka speaker use kare ..
4440 board me par channel karib 23 watt karke milta hai. Agar 12 volt 4 amps transformer use karte hai... 20 watt ka subwoofer use kar sakte hai, But 5 watt ka speaker full sound denese jal jayega...
Agar DC 12 v input dena hai to.. capacitor ke plus or minus me connection digiye.. Or agar ac 12 v input dena hai to... video me bataya gaya red and gray wire se connect kijiye..
12 volt 3 amp a66a rahega..4 amp bhi use kar sakte hai... But aapne agar 12 volt se jada use kiya to ic jal jayrga... 12 volt se jada use mat kigiyega...
4440 ic board me subwoofer ka line nahi hota.. Aap isne bus 2 speakers laga sakte hai.. Ya fir ek channel me 2 speakers and dusre channel me woofer connect kar sakte hai..
Sir apke iss wiring m volume se koi problem hui h kya..kyu ki mei apke jse same Kia but volume control nhi ho rha.. Apka chl rha tha Kya ase volume ke connection mei.. Agar kahi koi mistake ho to help me plz
Transformers ac to dc nahi hota... Transformers 220 volt ac ko 12 volt ac me convert karta hai... Use dc bananeke liye diod rectifier use karte hai....
@@TechTalkSwarup yes sir.transformers sirf ac to ac hi hothahe.vo voltage ko kam kartha he..diod ki matharse ham bridge rectifier banakarhi ham ko ac ko dc banasaktha he..
4440 ic board does not comes with vivid detailed high quality sound.. so you don't have to choose between speakers... Go for any mid range 30-40 watt speakers...
Sir you did a great job and this would help people to understand during DIY project. Very much appreciated. Sir could you please tell more at pin level of IC 4440 what all pins for output and what for input, ground and etc. I am learning electronics to build amplifiers and started with small steps. Plz let me know are you planning to have any online teaching.big you're in Bangalore I am ready to come n learn inperson
@@TechTalkSwarup sir aagar sirf 12v power supply , speaker , audio input connect kare (aur volume ,bass and trebel ni lagaye to work krega ?) Plz last question plz reply
Bass treble na lagaye to bhi chalega... but volume potentiometer lagana parega... ya phir volume ke line ko direct kar dena parega.. usse board ka volume always full rahega.
भाई अगर IC खराब हो तो उसकी क्या पहचान होती है मेरे पास एक 4440 IC का एम्पलीफायर है उसके एक कनेक्टर में आवाज कम और फ़टी हुई सी आ रही है और अगर IC बदलनी हो तो ये कैसे पता चलेगा कि दोनों में से कौन सी IC खराब है जैसा बोर्ड आपने वीडियो में दिखाया है ऐसा ही बोर्ड मेरे एम्पलीफायर बॉक्स में लगा है
bhai mere pas same yehi wala 6283 dvd kit hai kya usme mai 4440 ic laga skta hu ya 4440 se koi achhi ic bataye jo ki dhamake dar aavaj deti ho aui aise bord me fit ho sake plz bataye.
Bhai mujhe ek 12volt ki battery banani hai 3.7volt ke lithium cell se magar use charge karne ke liye 5 volt ka upyog karna hai. Bhai please suggest me.
Kisi battery ko full Charge karneke liye hamesa usse 1 volt jada use karna parta hai.. Aap voltage regulator ka use karke 5 volt ko 13 volt me convert kar sakte hai.. par usse charge honeme jada time lagega... Aap lithium batteries ko harbar ek ek karke charge kar sakte hai..
Brother please can you tell me I have four YP WOOFER 8 OHMS 120 WATT 10 inches and 30 0 30 TRANSFORMER which stereo amplifier will be best match for it with hifi bass and clear louder sounds please advise me I will be very thankful to you brother.
U can go for this board or boards like this one... Link - www.amazon.in/Powertronics-HI-FI-Subwoofer-Audio-Amplifier/dp/B07GPF2C4Y/ref=mp_s_a_1_33?ie=UTF8&qid=1544792118&sr=8-33&pi=AC_SX118_SY170_FMwebp_QL65&keywords=amplifier+board
Bhai same circuit board hai but blutooth se connected karne par operate ni hota agar ic ke in points par connect kar to volume bass trouble kam ni karte problem ka solution batao bhai ji.
Hey bro mere paas ek aisi circuit hai uske sari wiring bhi hey par power supply kaha Deni he muje nahi pata mene power supply tod di thi , usko power ek coil se milta tha vah koil bhi mere pas hey
@@TechTalkSwarup i mean,, i want to use only the bass treble from that circuit, so when i cut and take only that bass treble part where can i get the output.. got it bro?
Bhai aapke liye 9999999999999999999999999999999999🌟🏅👍👍👍👍👍like
Bhai thank you so much main bahut pareahan tha bhai mujhe koi video mil hi nhi rahi thi or jo mil rahi thi unke connection alag they so thank you so much ❤️❤️ Bhai
Welcome😊
Nice information video.
Thank you.Now I will add extra amplifier for my rear speakers in my car.
😅
Sir ji aap bahut acha se samjhe te hai
Please write required things and their rating in description
Required things are---
Three 100k potentiometer..
Wires..
And 4440 board itself...
(12 volt transformer, speaker)
Bhai aapki wajha se meri bohot badi help ho gai
Can we connect two speakers and two subwoofer with 4440 ic amplifier board
Or how much speaker we can connect it . explain with how much watt
4440 ic board is not that powerful. It consumes Only 12 volts not even 12-0-12..
U can get 40 watts at 4 ohms load..each channel...
It has 2 channels...
Biran Mandi
Reply
👍👍👍👍 video।।।।
Iska board ke liye 12v 1A DC kaphi heyyy????
Ha 1A se bhi chalega.. par 2A hua to jada a66a rahega.. board ka full power utilize hoga..
@@TechTalkSwarup ok,thanku sir
Our huming problem aya ,to kya korunga???
And me iss board me 6w 4ohms ke 2 speakers laga saptha hu!?
Humming ka one of the main reasons hota hai grounding.. agar humming aye to earth line ko heat sink ke sath jor dijiye..
Iss board me per channel 14 watts karke milta hai 4 ohms ke load pe..
Agar aap 1A use kar rahe hai to 6 watts ke speaker ko use kar sakte hai.. or agar 2 ya 3 A use kar rahe hai to 14 watts ke upar ka speaker use kare ..
Kai me is me 4440 ic amplifier boardme 12" ka speaker 40watt ka speaker baja sakta hu ...... please reply
Is board se per channel 17 watts karke milta hai..4ohms ke load pe.
To nahi chala sakte hai.
Bhai bahut acchi video banai aapane lekin video background music kam rakha krey
Thanks again
Tq bhai saab for good video, iska output me kitna watts milega? 30w, 4ohm speakers lega sakthe?
Per channel 4 ohms ke load pe 14 watts milega...
30 w speaker use kar sakte hai...
Sekar
Kya mai isme ek 5 watt ka speaker and ek 20 watt ka subwoofer laga shakta hu?
Please tell me instantly
4440 board me par channel karib 23 watt karke milta hai. Agar 12 volt 4 amps transformer use karte hai...
20 watt ka subwoofer use kar sakte hai,
But 5 watt ka speaker full sound denese jal jayega...
@@TechTalkSwarup to mujhe kitne watt ka speaker dena padega😕?
20-30 watt ka speaker use karenge to a66a rahega...
Bhai bhut achha lga 🙏🙏🙏🙏🙏thank you
Thank you❤🌹❤❤❤❤
Bahut acchi Tarah Se samjhaya
Amazing bro video was very helpful ....
Bhaiya ji kya ham is board 4440 me 2amp ka transfarmar laga sakte hai
Ha.. use kar sakte hai..
Input me aapne jo 3 wire lagaye h
Usme USB or AUX dono kaam le sakte h
Nahi.. aux or usb ke liye alag se iss board me connection nahi hai.. display board lagakar.. usb or aux use kar sakte hai..
Dil khosh ker diya bhiya
Capacitor ke pass kaun sa input Dena padega Kaise video mein bataiye
Agar DC 12 v input dena hai to.. capacitor ke plus or minus me connection digiye..
Or agar ac 12 v input dena hai to... video me bataya gaya red and gray wire se connect kijiye..
Baja Baj rahi hai transparent Se Laga rahe hain to
😎
*सड़कें भले ही 30 फिट की क्यों न हों*
*लेकिन ब्रेकर के पास टूटी हुई जगह से आप नहीं निकलते तो आप सच्चे भारतीय नहीं हैं*
😉😉😉😂😂
Thanks bro😍😍
KY air be videos be banker aap baja shakta ha
Base trouble ke liye 47k pot use nhi kr skty ?
Ha kar sakte hai...
Tq bro👌👌👌👌❤️
ऐसे ही भाई वीडियो बनाओ यार कि सभी कुछ समझ में भी आए
Sir , when I am holding my hand on ground wire than no noise is coming.. but whenever i remove my hand it gives huge noise
Connect the earthline to the ground line of the board..
@@TechTalkSwarup in my adapter i have 2 wires coming , +12v and Earth . Please demonstrate me how i should do it . (4440 ic amplifier)
Pata kase lagaya ke Bass point kon sa h aur trabal aur volume kon sa h
@@PankajKumar-dl6mm yahan TTT likha wo treble jahan BBB likha wo bass
Bhai ye 12 volt 4ah battery se chalega??
Ha chalega...
@@TechTalkSwarup bhai maximum kitne amp ki battery hum 4440 amplifier board me use kar skte hai
Aux cable kise concect kare
Aapke jese koi nhi samjate
My pleasure..
Kai me iss 4440 ic amplifier board me 3ohm ka speaker baja sakta hu ...... Please reply
Ha.. baja sakte hai.
Sir isme kitana vlt dc our kitan vlt ac laga sakte hai
Isme dc 12-0 volt lagega
Good sir
Iss 444O ic amplifier board ka speaker output ka ohm kitna hai...... please reply. .....
4 ohms speaker comfortable hai..
Speaker wire ka. (+) ( - ) konsa he?
+ 10 no. Vali pin h or - 12 no. Vali jab aap left side se count kroge
12 0 12 ki jaga kya 12 volt ke adapter se kam liya ja skta hai ?
Ha.. 12-0 volt hi use karna parega...
@@TechTalkSwarup ok bro thankyou for fast reply..
Ossume vdo sir
12volt 3amp desakte hai issmein...? Konsa Achha rahega 12 volt 2amp ya 12volt 3amp...12volt se agar jada(12-18)hoga toh kiya problem hoga
Ha.. de sakte hai...
@@TechTalkSwarup par achha konsa rahega sir....? 12 volt 2amp ya 12volt 3amp...12volt se agar jada(12-18)hoga toh kiya problem hoga
12 volt 3 amp a66a rahega..4 amp bhi use kar sakte hai...
But aapne agar 12 volt se jada use kiya to ic jal jayrga...
12 volt se jada use mat kigiyega...
@@TechTalkSwarup Thank you so much sir
You're welcome...
I cannot skip the bass and treble control
Thanks
Mujhe 2 speaker or 1 woofer lagana hai.Speaker kaha lagana hai wo to mai samajh gaya par mai woofer kaha du?😕
4440 ic board me subwoofer ka line nahi hota..
Aap isne bus 2 speakers laga sakte hai..
Ya fir ek channel me 2 speakers and dusre channel me woofer connect kar sakte hai..
Thanks bhaia
Sir agr hmare pass potential meter na ho or hum Direct full volume chalana chahate ho to kaise krenge ...pls sir reply dena
Potentiometer ke ground lines ko use na kare....
Or baki do wire ko eksath jor dijiye .. direct connection ho jayega ...
@@TechTalkSwarup ok sir and thanks for your reply 🙏
Please give circuit diagram of this board
Sir apke iss wiring m volume se koi problem hui h kya..kyu ki mei apke jse same Kia but volume control nhi ho rha.. Apka chl rha tha Kya ase volume ke connection mei.. Agar kahi koi mistake ho to help me plz
Sabhi board same nahi hote hai.. kuch kuch board alag hote hai..
Firbhi Make sure ki apka potentiometer thik kam kar raha hai.
Mere paas 4440 ic ka board hai jisme DC power ki supply hai usme direct ac kaise connect karu
Uske liye ek rectifier jorna parega board se.. or fir usse transformer connect karna parega..
Ac to dc transformer hai bhi
12-0-12 dc 3mp transformer connection kare bhi
Transformers ac to dc nahi hota...
Transformers 220 volt ac ko 12 volt ac me convert karta hai...
Use dc bananeke liye diod rectifier use karte hai....
@@TechTalkSwarup yes sir.transformers sirf ac to ac hi hothahe.vo voltage ko kam kartha he..diod ki matharse ham bridge rectifier banakarhi ham ko ac ko dc banasaktha he..
Input fimel pin me koi rjistor lagega ki direct chalega
Input Direct lagega...
@@TechTalkSwarup thenks bhai
What is the cost of this board
Mejhe 180 /- paratha....
🌹 AWESOME BRO👍👍 I'LL TRY NOW🙏🙏🙏
Sir can you suggest me some speakers for this ic.
4440 ic board does not comes with vivid detailed high quality sound.. so you don't have to choose between speakers...
Go for any mid range 30-40 watt speakers...
Potentialmeter short karke direct kar sakte hain ?
Ha jarur..
Potentiometer ke upar ke 2 or 3 no. pin ko eksath jor dijiye..
and niche ke 2 or 3 no. pin ko eksath jor dijiye...
Direct ho jayega...
@@TechTalkSwarup aur agar amplifire board se karna hain to..?
Ha jarur kar sakte hai koe problem nahi...
@@TechTalkSwarup is par video bana sakte hain...?
To aasan hoga karne main....
Upar or niche ke 1 no. pin kor kuch karneki jarurat nat....
Bus potentiometer ko disconnect karke.. aage ke comment me jo kahatha wo kijiye...
Nice
Isi bord me keval volume ka conection bich me se kre to kam jyad voice hogi ya nhi bina bas treeble ke alg vidio bnaya
4011 Amplifier kaise banay
Sir you did a great job and this would help people to understand during DIY project. Very much appreciated.
Sir could you please tell more at pin level of IC 4440 what all pins for output and what for input, ground and etc.
I am learning electronics to build amplifiers and started with small steps.
Plz let me know are you planning to have any online teaching.big you're in Bangalore I am ready to come n learn inperson
ALL वइरिग
पुरा वइरीग किजिऐ
Sir aagar isme bass or trebel ni lagayenge to chalega kya? Please help me.
Ha chalega.. tub apko volumn potentiometer se audio input dena parega.
@@TechTalkSwarup sir aagar sirf 12v power supply , speaker , audio input connect kare (aur volume ,bass and trebel ni lagaye to work krega ?) Plz last question plz reply
Bass treble na lagaye to bhi chalega... but volume potentiometer lagana parega... ya phir volume ke line ko direct kar dena parega.. usse board ka volume always full rahega.
@@TechTalkSwarup THANK YOU SIR ☺️
Supppppper bro
Kya bina bass treble button k APM work karega
Bhai Mara sa akbar contact karo
Please
Aap mujhe email kar sakte hai...
@@TechTalkSwarup kaysa karu
8116532383 my number please contact
Sir muje ek doubt h..agar ham direct ac lgate h.to kitna input dena hoga..aur agar dc de to kitna input dc..
12 volt input dena hoga
Ac mei kitna input aur dc m kitna...dono mei 12 volt??
Balance ke bhaiya to Lagai Nahin
Is board me balance ka connection nahi hai...
Sir je amplifier board kitne Watt ka speaker chala Shakta hai plz bata de dijiye
Isme per channel 17 watts karke milta hai 4 ohms ke load pe.
@@TechTalkSwarup ok thanks sit
Sir
Recording by teacher
Thank you bahi😊❤❤
potiso mitar sab 1 hi hay
Haa..
Bhi 200w spikar ke liye konsi ic wala board laye jise sound dj ki tarh aayi tacotar me lagani hai achi ic wala board batao jise sound dj ki tarah aayi
🙏👌
Great video thanks bat बेलानस Ka volume nahi bola
Is board me balance control nahi hai.
@@TechTalkSwarup oho
बजाकर दिखाये। अभी ग्यान अधूरा हैं।
Video bohot lamba ban gayatha..
Aagli bar jarur bajake dikhunga...
2channel me 2 alag alag watt ke speaker chala sakte hai?Koi nuksan to nahi hoga?
Chara sakte hai.. koi problem nahi..
Like
4440 İc ke pleat se kis namber se ax nikalta hai
Mai kar ke dhek raha hu agar shi hua to thank you bro
Kya ye circuit Ac current se direct chal sakta hai
Aur DC current se wiring kaise karenge
Ji haa... ise 12 volt ac supply dena parega.. dc supply deneke liye capacitor ke plus minus me connect kare...
Good bhai saab 👌👌👌
भाई अगर IC खराब हो तो उसकी क्या पहचान होती है मेरे पास एक 4440 IC का एम्पलीफायर है उसके एक कनेक्टर में आवाज कम और फ़टी हुई सी आ रही है और अगर IC बदलनी हो तो ये कैसे पता चलेगा कि दोनों में से कौन सी IC खराब है जैसा बोर्ड आपने वीडियो में दिखाया है ऐसा ही बोर्ड मेरे एम्पलीफायर बॉक्स में लगा है
Aagar 4440 ic kharab ho jaye to, on karne se ic bohot jada heat ho jata hai...
@@TechTalkSwarup thanks
bhai mere pas same yehi wala 6283 dvd kit hai kya usme mai 4440 ic laga skta hu ya 4440 se koi achhi ic bataye jo ki dhamake dar aavaj deti ho aui aise bord me fit ho sake plz bataye.
Bhai ek bar pure plet ki waiting Ka video banaiye Pura kampalit
Bhai ji potentiometer konse lagaye aapne bass volume or treble.... Plz btao mujhe lagane hai
Six pin 100k potentiometer.
. lagaya hai...
@@TechTalkSwarup bhai kya 10k ka bhi laga sakte hai
Nahi iss board main 100k ka lagega...
Bahi ise 12 0 12 ke transfomer se chala sakate hai kya reply me🙏🙏🙏🙏🙏
Ha... koe problem nahi... sirf bich ka wire and side ka ek wire use kare.. or ek wire use na kare.
Isme speaker kitna go lag sakta hai agr mei 3 3 waat ka lagaunga to
Isme per channel 17 watts karke milta hai.. 4 ohms ke load pe..
thanks bro for make this video
Welcome..
हम अपने मसीन का फोटो भेज रहे हैं
how to control and balance between left and right channel. can we put any Knob to balance
Yes that is possible.. but u have to do it manually as this board does not have a balance connection.
@@TechTalkSwarup but how. can u tell me.plz
Bhai mujhe ek 12volt ki battery banani hai 3.7volt ke lithium cell se magar use charge karne ke liye 5 volt ka upyog karna hai. Bhai please suggest me.
Kisi battery ko full Charge karneke liye hamesa usse 1 volt jada use karna parta hai..
Aap voltage regulator ka use karke 5 volt ko 13 volt me convert kar sakte hai.. par usse charge honeme jada time lagega...
Aap lithium batteries ko harbar ek ek karke charge kar sakte hai..
Bhai single 4440ic kit par wiring karne ki video banao duol ic kit me hi
Home theater मैं 4440 इस्तेमाल कर सकते है
4440 me sirf 2 channels hote hai.. yaniki aap 2 speaker baja sakte hai.. par bass ke liye alag se woofer ka line nahi hai iss board me..
@@TechTalkSwarup bass trable kit bhi nhi lga skte hum isme bass k liye
Sir la4440 jyada output deta hai ya tda2030???
4440 se tda2030 jada powerful or jada a66e quality ka hai...
Hii bro....
I need 6283 ic amplifier full wiring details... Can you please make a video or suggest me in personal.....
Please reply...
bahud asan hai 6283 ka wiring karna
Very nice 👍👍👍 sir
Kya ye 12v 7ah bettery me chalpayega?
Ha chalega...
4440 ic kit mei 2 driver unit chala sakte hai kya sir 40. 40 vott ka batana pls
40 watt 8 inch*2
Bhai same 4440 ki cerkit board ka price kya hai
Bro please reply how many Volt dc can be connected to it and please mention it's Ampere.
It requires 12 volts dc/ac.
Ideal would be 3 ampere.
@@TechTalkSwarup okay thanks for replying, nd now I'm using 9v 1amp..and at high volume the sound distorts, is it due to low power of the adapter
Yes
@@TechTalkSwarup bro i had updated the adapter with 12v but it still makes a distorted sound when reaching 50% do u know why❓
Brother please can you tell me I have four YP WOOFER 8 OHMS 120 WATT 10 inches and 30 0 30 TRANSFORMER which stereo amplifier will be best match for it with hifi bass and clear louder sounds please advise me I will be very thankful to you brother.
U can go for this board or boards like this one...
Link - www.amazon.in/Powertronics-HI-FI-Subwoofer-Audio-Amplifier/dp/B07GPF2C4Y/ref=mp_s_a_1_33?ie=UTF8&qid=1544792118&sr=8-33&pi=AC_SX118_SY170_FMwebp_QL65&keywords=amplifier+board
For best performance must use 30-0-30 volt 5 to 8 amps transformer
@@TechTalkSwarup I have 30 0 30 TRANSFORMER I want to know which amplifier board I will make
go for TTC 5200 amplifier board..
@@TechTalkSwarup thank you very much
nice video sir
12 volt battery connection kaha de usme dayod lagega ki nahi
Board ke power supply me jo bara capacitor hai.. uske plus and minus point me battery connect kijiye...
Diod ki jarurat nahi hai...
Thank you..
Bhai same circuit board hai but blutooth se connected karne par operate ni hota agar ic ke in points par connect kar to volume bass trouble kam ni karte problem ka solution batao bhai ji.
Volume potentiometer ke jo 6 wires hai unme se 2 wires left and right input line hai.. waha input deke dekhiye...
Regulater kon sa lagaya hai volume,bass,treble
You can use 47k
Sir amplifier me aux line output connection kaise kare .plz bolo ❤️❤️
Uske liye alag se ek circuit lagana parega board ke input me..
Hey bro mere paas ek aisi circuit hai uske sari wiring bhi hey par power supply kaha Deni he muje nahi pata mene power supply tod di thi , usko power ek coil se milta tha vah koil bhi mere pas hey
Aapka WhatsApp number do muje uski photo bhejni hey me Gujarat se hu me student hu
Sorry i do not have a official whatsapp number yet. You can email me...
techtalkswarup@gmail.com
Brother Maine aapko Gmail Kiya hey
I did not received any mails in the above mentioned email.
Bro,,where il get the output if i use only the bass treble cn u tell me pliz..
Please be specific to your question.. i can not understand you.
@@TechTalkSwarup i mean,, i want to use only the bass treble from that circuit, so when i cut and take only that bass treble part where can i get the output.. got it bro?
trible anbass के लिये कित्ना k का pot लगेगा please .
100k bhi use karsakte hai ....