Tip for scraping the inside of the gourd: take an old spoon, cut off the handle and sharpen one half of the bowl, you now have a scraper with every curve you'll need. That's how I do it, works a treat!😊
Nice job making the banjo and video! That gap at the back of the headstock doesn't need to be set in by drilling anything. On the back of those tuners is a sharp pin that keeps them from turning once they are tightened down. You just need to tighten them from the other side and that point will dig into the wood and will make the tuners flush. Also, you can get some offcuts of absolutely flat marble from kitchen suppliers and use that as a flat surface to glue/tape some sandpaper down to sand the top of your gourds flat. Nothing wrong with what you're doing, you just mentioned you were not happy with the flatness and your process for that.
Yeah, I think the way I did the headstock, the backside wasn't flat, so they wouldn't sit flush even with the pin all the into the wood (and I got nervous about overtightening). Idk though, I did something weird, but it worked out in the end at least. I'll have to check out some kitchen suppliers, that would be amazing to have some flat marble! Just the other day ground another gourd out on the asphalt and I think that's the last time I wanna do it. Just a messy way to go, even though it gets the job done. Thanks for the tips and for watching!
@@bengreco yeah keep up the good work man. Looking and sounding good. The marble offcuts are good. But for the gourds you could even get away with a small piece of 3/4" plywood with sandpaper glued on. Would definitely be flat enough for that. I like having the marble though. But it's a bit heavy to move around
I built a couple of banjos and know it never goes without hitches your good at problem solving so you'll get better and better enjoyed your video very much thanks from joe brady in South Carolina
I realize this is an older video, and you seem after improving, so you might have already found a way. But another solution to the sanding on asphalt, glueing sandpaper to a sheet of glass, like an old window, was what came to mind
Keep up the great work, the tone and look of this one are awesome! I'm only just now starting my journey as a wannabe luthier and these videos are really inspiring! Thank you for the effort put in to film/edit as well!
Thanks!! Yeah I used to have a junk harbor freight one but when it broke I figured I use it so much it's worth spending a little. Also this one is self-centering which is amazing
I got my standing drill press from harbor freight. It cost me less than $500. The main thing is getting good bits because the press only needs to spin.
thanks! Tough to find gourds on the west coast now for some reason, I used to get them from Welburn gourd farm near Temecula, but I'm from upstate NY so some of the best one's I've gotten were from amish gourd farms around Lancaster, PA. They're much easier to find in the east, many more growers. Out here in socal, there's really just Welburn, and they don't have much to offer now
thanks! there are good plug cutter bits you can buy, but a while ago I bought a cheap 1/16" leather stamp from harbor freight and filed teeth in it so it would cut wood, and I've been using that since. It kinda sucks though and I'm probably gonna buy a proper plug cutter soon
To strenghten the interior of a gourd why not use thin slats of wood glued in place or a dense coat of papier-mache.using wood glue as a binder ? To clean the interior a curved knife like the one use by american indians?
I'll have to try that, I haven't heard of that before. I also want to try melting granular hide glue into the inside of the gourd, someone told me it really hardens things up. Really sick of the fiberglass haha
I love my banjo!!! Thanks again Ben!
Tip for scraping the inside of the gourd: take an old spoon, cut off the handle and sharpen one half of the bowl, you now have a scraper with every curve you'll need. That's how I do it, works a treat!😊
interesting, I've tried using a spoon but didn't think to sharpen it. I'll give that a go!
Well done Ben! She’s a beauty!🪕
This is an amazing build. Impressive how you use basic tools to create something so well put together
wire brush on the end of the drill is a really genius tip
yeah, I just tried it for the first time yesterday and it's a game changer. can't believe I never thought of it before
I really love how your banjos have a distinct character. As in I’d probably recognize them as yours if I would spot one.
thanks! that's the ultimate compliment for what I'm going for
Great tone on this banjo ... rich and atmospheric. Looks great too.
Nice job making the banjo and video! That gap at the back of the headstock doesn't need to be set in by drilling anything. On the back of those tuners is a sharp pin that keeps them from turning once they are tightened down. You just need to tighten them from the other side and that point will dig into the wood and will make the tuners flush. Also, you can get some offcuts of absolutely flat marble from kitchen suppliers and use that as a flat surface to glue/tape some sandpaper down to sand the top of your gourds flat. Nothing wrong with what you're doing, you just mentioned you were not happy with the flatness and your process for that.
Yeah, I think the way I did the headstock, the backside wasn't flat, so they wouldn't sit flush even with the pin all the into the wood (and I got nervous about overtightening). Idk though, I did something weird, but it worked out in the end at least.
I'll have to check out some kitchen suppliers, that would be amazing to have some flat marble! Just the other day ground another gourd out on the asphalt and I think that's the last time I wanna do it. Just a messy way to go, even though it gets the job done. Thanks for the tips and for watching!
@@bengreco yeah keep up the good work man. Looking and sounding good. The marble offcuts are good. But for the gourds you could even get away with a small piece of 3/4" plywood with sandpaper glued on. Would definitely be flat enough for that. I like having the marble though. But it's a bit heavy to move around
I built a couple of banjos and know it never goes without hitches your good at problem solving so you'll get better and better enjoyed your video very much thanks from joe brady in South Carolina
thanks appreciate it! haha yeah something always goes wrong but I guess it keeps me from getting bored!
I realize this is an older video, and you seem after improving, so you might have already found a way. But another solution to the sanding on asphalt, glueing sandpaper to a sheet of glass, like an old window, was what came to mind
Awesome work as always!
Keep up the great work, the tone and look of this one are awesome! I'm only just now starting my journey as a wannabe luthier and these videos are really inspiring! Thank you for the effort put in to film/edit as well!
WOW Ben !!!!!!! That's an awesome looking piece.
Man that planer you have is nice! My old rigid is tired and done 😂
Beautiful woodwork too. That thing is sweet!
Thanks!! Yeah I used to have a junk harbor freight one but when it broke I figured I use it so much it's worth spending a little. Also this one is self-centering which is amazing
@@bengreco that’s a huge plus to have on that planer! I need to find one asap.
Was waiting for this 😂
I got my standing drill press from harbor freight. It cost me less than $500. The main thing is getting good bits because the press only needs to spin.
great!
Hey Ben beautiful job on this banjo I'm interested in buying one from you please let me know cheers man
Great build! And, yes, very sketchy circular saw bit... 🤯
A thick peace of glass is what some use for a lapping surface.
Great build dude. Where do you get your gourds?
thanks! Tough to find gourds on the west coast now for some reason, I used to get them from Welburn gourd farm near Temecula, but I'm from upstate NY so some of the best one's I've gotten were from amish gourd farms around Lancaster, PA. They're much easier to find in the east, many more growers. Out here in socal, there's really just Welburn, and they don't have much to offer now
A fitting end tune, the banjo was a bit of trouble on your mind.
hahaha true, they all are
Do you have an average pricing for these? Super cool man!!
yeah custom builds are around $700 depending on materials, but I'll sell non custom builds for less
Enjoying your videos! Curious to know what sort of bit you are using that allows you to make the little plugs / pips? Thanks!
thanks! there are good plug cutter bits you can buy, but a while ago I bought a cheap 1/16" leather stamp from harbor freight and filed teeth in it so it would cut wood, and I've been using that since. It kinda sucks though and I'm probably gonna buy a proper plug cutter soon
your flat surface can be a piece of plate glass
I wonder what a left handed version of something like this would cost...
Hey so I was wondering about pricing on your instruments. For a travel size gourd banjo that is fretless how much do you charge?
try a cabinet scraper
🔥.🔥
where do you get gourds?
This one's from Welburn gourd farm in southern CA, I also get some from the Amish in PA
Get a set of jewelers files for nut and bridge slots.
Could you ship to TN?
yep! I can ship anywhere in the US pretty easily, and internationally too
RUclips algrythm thought I'd like it. Did.
You need hardwood for the tailpiece
I used cherry on this one, but I've had better luck with hard maple
To strenghten the interior of a gourd why not use thin slats of wood glued in place or a dense coat of papier-mache.using wood glue as a binder ? To clean the interior a curved knife like the one use by american indians?
Wood glue and burlap could be a less toxic strength instead of fiberglass or cotton duck cloth it’s called poor man’s fiberglass
I'll have to try that, I haven't heard of that before. I also want to try melting granular hide glue into the inside of the gourd, someone told me it really hardens things up. Really sick of the fiberglass haha
@@bengrecowood glue and paper too believe it or not. Dries rock hard. Nice work btw.