Thanks for putting this together, I brought 3 faulty batteries from ebay (all new but discharged) to fix and now they all work! (touch wood) I used a USB lipo charging board to charge each cell to just over 4.1v and used the firmware to update. Great tip with the copper tape for the drone connector!
How I charged cells. Here's what I did: I used a regular battery charger designed for AA batteries, connecting two wires with positive (+) to positive (+) and negative (-) to negative (-). Then, I checked all three cells by referring to images online that indicate the positive and negative terminals of each cell. After checking the voltage of each cell, I discovered that one out of the three had a voltage below 2V. I charged that particular cell up to 2.11V (while the other two cells were around the same range, 2.11V to 3V). Charging just that one cell was sufficient. I reconnected it to the chip, ran the software, and it worked like a charm. Similarly, with my second battery, the voltages were similar, except this time the bottom cell was below 2V. I charged it to 2.11V, ran the software, and everything worked perfectly. The batteries now look brand new and function flawlessly.
How about putting a capacitor across V+ and V-, with a battery plug cable attached from there? Then you can swap the batteries without the voltage dropping too low? There would be a big jump in voltage when the recharged battery is swapped in, but maybe that wouldn't hurt anything. Thanks.
@@mihaigsm2003 Depending on input bias current plus capacitor leakage current, versus capacitor size. Do you know the specifics? Have you tried? Assuming you quickly swap the battery.
Dear Sir. An additional information: I made the charge with 13V directly in the cells terminal, between + and -- in the borders of the board (such as an unique cell). My new question: is this arrangement would made a damage in any component? Thanks a lot. Leonardo Vieira.
Hi Taranu... My batteries are not responding (dead)... I opened one and bypassed the board attached and I was able to charge the stacks (3 stacks). However, after closing the housing and trying to switch the battery from the power button, it is still not responding. Will EV2300 module solve this problem following your steps?... thanks
Hello Sir. I´m having problems to access the batteries. I have four batteries and only one is Ok (fully usual and flying). The other three are dead and I provided charge to them using a external font (directly in cells terminals). I´m using a Raspberry Pi for interface I2C but the communication occurs only with good battery. Do you have any idea to help me? Thanks. Leonardo
@@mihaigsm2003 At the first, thanks for your very fast response. I will check the diodes and resistors, but I don't know what are the communication pins on the board (I´m connecting comm pins in the main connector of the battery). Really, really gratefull for your attention. Leonardo Vieira (from Brazil).
@@mihaigsm2003 I´m with 100% of certain about I made correct connections in batteries connector and the problem occurs in three batteries. Do you know other points in the board (maybe wire soldering) to make connections in comm line? Thanks. Leonardo.
Buna ziua. Am o baterie de magic air,are 2 ani , n a fost niciodată încărcată. Este moarta. Exista posibilitatea refacerii,si înlocuirii celor 3 celule de acumulatori? Contra cost,evident?
@@mihaigsm2003 Why can't fly , i want to just wake up the battery like this then i will try to charge it with the original charger from the manufacturer.
@@mihaigsm2003 even if i charge batteries somehow (bypass board) after that i need to reactivate bms to use the battery ? how can i reacticated ? is the only way to do this is to buy chip that can activate the bms ? thank you
hi I'm from Brazil. I have some dead mavic batteries. already performed several procedures. I want to buy your apadtador EV2300 and the software to be able to access the controller board. do you have the link where i can do this?
@@mihaigsm2003 thank you i have charged cells on mavic air battery back up individually as per your excellent video. but the cells or one of themmust be Pf ( locked ) so i need to dig deeper to fix which means the EV2300 and interface software i guess
Hello, great tutorial thx. But I have two Questions, could this fix be done without Opening the battery? Will the permanent fail deleted forever, so it couldn't come again, also when I Change the battery cells?
The price for the UBRT software is too expensive. We all use DJI Battery Killer instead. It is free with option to make a donation to the Ukrainian developer.
Hey there Jack, sorry to interrupt but I couldn't find the Battery Killer software anywhere, could you please link me up with any valid and available source? Thanks in advance.
@@atylasouza8151 есть программа скачанная с форума и бесплатная, у меня она есть, только не знаю как отправить файл. Напиши мне адрес куда отправить dji battary killer
@@atylasouza8151 there is a program downloaded from the forum and free, I have it, but I don’t know how to send the file. Write me the address where to send the dji battary killer
Thanks for putting this together, I brought 3 faulty batteries from ebay (all new but discharged) to fix and now they all work! (touch wood) I used a USB lipo charging board to charge each cell to just over 4.1v and used the firmware to update. Great tip with the copper tape for the drone connector!
hi, can you explain to me what you did to repair your batteries?
Thanks for this.. had no idea you could do this ... Dji should be ashamed for selling such a faulty product .
How I charged cells. Here's what I did: I used a regular battery charger designed for AA batteries, connecting two wires with positive (+) to positive (+) and negative (-) to negative (-). Then, I checked all three cells by referring to images online that indicate the positive and negative terminals of each cell. After checking the voltage of each cell, I discovered that one out of the three had a voltage below 2V. I charged that particular cell up to 2.11V (while the other two cells were around the same range, 2.11V to 3V). Charging just that one cell was sufficient. I reconnected it to the chip, ran the software, and it worked like a charm.
Similarly, with my second battery, the voltages were similar, except this time the bottom cell was below 2V. I charged it to 2.11V, ran the software, and everything worked perfectly. The batteries now look brand new and function flawlessly.
Need to change cells above 4,2v, all cells
@@mihaigsm2003 I am just saying what I did and it worked.
Im using cp2112 adapter it will work or not?
Can you perform this fix without opening the battery cover?
How about putting a capacitor across V+ and V-, with a battery plug cable attached from there? Then you can swap the batteries without the voltage dropping too low? There would be a big jump in voltage when the recharged battery is swapped in, but maybe that wouldn't hurt anything.
Thanks.
Capacitor will drop voltage until will swap cells. Difference from voltage will get permanent fail
@@mihaigsm2003
Depending on input bias current plus capacitor leakage current, versus capacitor size.
Do you know the specifics?
Have you tried? Assuming you quickly swap the battery.
can i use CP2112 debug board USB to I2C Communication Module please answer fast
I love the video
Hello sir, may I know the status of the battery before repair?
Is it not charging or not starting at all (no led, completely dead)
Thanks a lot
If not start is on permanent fail
@@mihaigsm2003 if the cells have dropped below normal voltage, and the battery won't turn on, could i charge it initially by jumping the board?
Dear Sir.
An additional information: I made the charge with 13V directly in the cells terminal, between + and -- in the borders of the board (such as an unique cell). My new question: is this arrangement would made a damage in any component?
Thanks a lot.
Leonardo Vieira.
No
What voltage and current dud you set the charger at please to start each cell individually by bypassing the smart circuit board
@@arroyodflint7114 use 4,2v with maximum 2 Amper
@@mihaigsm2003 Thanks, regards and happy new year.
Hi Taranu... My batteries are not responding (dead)... I opened one and bypassed the board attached and I was able to charge the stacks (3 stacks). However, after closing the housing and trying to switch the battery from the power button, it is still not responding. Will EV2300 module solve this problem following your steps?... thanks
Sure.
@@mihaigsm2003 Thank you so much for your reply. Do you recommend any similar/cheaper module than EV2300?
@@ahmedelsheikh1987 not exist similar.
How many charges can I expect to get from a Mavic Air battery that I have taken good care of?
you are a savior my friend very informative
Hello Sir.
I´m having problems to access the batteries.
I have four batteries and only one is Ok (fully usual and flying).
The other three are dead and I provided charge to them using a external font (directly in cells terminals).
I´m using a Raspberry Pi for interface I2C but the communication occurs only with good battery.
Do you have any idea to help me? Thanks. Leonardo
connect charger for 3 seconds, if not communication check communication pins on board, will see 2 resistors and 2 diodes , check both.
Check if diodes is not shorted
@@mihaigsm2003 At the first, thanks for your very fast response.
I will check the diodes and resistors, but I don't know what are the communication pins on the board (I´m connecting comm pins in the main connector of the battery).
Really, really gratefull for your attention.
Leonardo Vieira (from Brazil).
@@leonardovieiradesouzajunio1292 if you push voltage on sda or scl diodes going to shortcut
@@mihaigsm2003 I´m with 100% of certain about I made correct connections in batteries connector and the problem occurs in three batteries.
Do you know other points in the board (maybe wire soldering) to make connections in comm line?
Thanks.
Leonardo.
may i get license for red lable, how can I get it for EV2300.
Buna ziua. Am o baterie de magic air,are 2 ani , n a fost niciodată încărcată. Este moarta. Exista posibilitatea refacerii,si înlocuirii celor 3 celule de acumulatori? Contra cost,evident?
Hello, your video is very nice. I have the same problem with my battery. I am writing to you from Turkey. Can you post the program you used?
Hi, I use ubrt software, it’s not for free.
@@mihaigsm2003 how much
@@anlgultekin go to site to see prices. Depending what license you need. I not selling software, I buy too. I pay for start 300$ annual.
Hello did you get the drivers for the ev2300 coz I can't get it to be recognized by the PC. How do you get driver please
how may i purchase it.???@@mihaigsm2003
has video teaching the points to reactivate phantom 3 battery? my battery is charged, but does not turn on the leds
Does this work with CP2112?
Sir Can we repair mavic Pro 2 battery 🔋? In ev2300 & ubrt
hi Sir, if we replace the cell with ordinary lipo, does the battery gets bricked, my target is to put 1800mah 35C lipo inside this
good afternoon i need the softer to download now how much i paid you. need urgent
i have some dead battries that cannot turn on. can this tools and software resolve the problem?
This setup work for mavic 2 battery?
Cum se numește dispozitivul acela de sunt conectate firele in acumulator ?
Se vede chiar la inceputul clipului. Interfata EV2300
These batteries are programmed to brick if the voltage drops too low?
Yes
Fff bun..bravo..respecte ptr realizare...
Where can I get the Licence ? I already bought EV2300
Wait some days, I will test new software. Stay on!
if the cells have dropped below normal voltage, and the battery won't turn on, could i charge it initially by jumping the board?
U can change by jumping but can’t fly
@@mihaigsm2003 Why can't fly , i want to just wake up the battery like this then i will try to charge it with the original charger from the manufacturer.
@@fluidmind3629 need reactivated BMS
@@mihaigsm2003 even if i charge batteries somehow (bypass board) after that i need to reactivate bms to use the battery ? how can i reacticated ? is the only way to do this is to buy chip that can activate the bms ? thank you
@@fluidmind3629 only need programming chip
where is the contact point for mavic 2 pro?
ruclips.net/video/0rHUWEEjpms/видео.html
$200 for a license to repair DJI batteries. Might as well order one for $80 through their support. They still have plenty. Just order 3.
Buy license from laptopu.ro , only 129$ for 1 year
hi I'm from Brazil. I have some dead mavic batteries. already performed several procedures. I want to buy your apadtador EV2300 and the software to be able to access the controller board. do you have the link where i can do this?
woldfish woldfish see description
Hey i want to sell my ev2300 kit, I had bought 2 pcs want to sell of my 1 extra kit it's an unused piece.
Eu já estou fazendo
@@santossantos7099 Olá Santos...sou aqui do RS
@@woldfishwoldfish6493 to fazendo irmao devagar ta indo
Cool buddy thank you . Where do I get the inter Dave computer software from for windows 10 64 please
What?
sorry .. the interface software thats on your Monitor in the video.. where can i download this software
@@arroyodflint7114 search my videos, will find link
@@arroyodflint7114 it’s not for free
@@mihaigsm2003 thank you
i have charged cells on mavic air battery back up individually as per your excellent video. but the cells or one of themmust be Pf ( locked ) so i need to dig deeper to fix which means the EV2300 and interface software i guess
Hello, great tutorial thx.
But I have two Questions, could this fix be done without Opening the battery?
Will the permanent fail deleted forever, so it couldn't come again, also when I Change the battery cells?
if battery discharged no way...
salut. repari bateri si daca iti trimitem?
Da, trimite
@@mihaigsm2003 salut unde te pot contacta? o adresa de mail?
@@In7heaven incearca mesaj privat
@@mihaigsm2003 salut , multumesc am trimis pe yahoo mail.
is there a cheaper alternative to the EV2300?
any i2c to usb adaptor would do
@@praveendesaa3851 My friend, is there another cheaper one with free software? Thank you very much.
@@willalexbombraga7807 ftid chips can work
Which version of UBRT software do I need to buy to perform this unlock?
Black
how may i get this, or which site have this license???@@mihaigsm2003
what will happen if i dont seal the battery, only unseal ?
Can’t fly, get error messages from drone
Salut , am 4 baterii si sunt moarte ,le pun la încărcat și nu se întâmplă nimik .... se pot face ? Mersi !
da
How can i get this software it is around usd 600
Has anyone tried this with the TRB sw and Chinese ev2400?
No
The price for the UBRT software is too expensive. We all use DJI Battery Killer instead. It is free with option to make a donation to the Ukrainian developer.
Hey there Jack, sorry to interrupt but I couldn't find the Battery Killer software anywhere, could you please link me up with any valid and available source? Thanks in advance.
Am și eu o baterie de mavic air, puteți sa ma ajutați sa o reduceți la viata?
can i change my cycles?
Yes
@@mihaigsm100 what software i must use ? with dji battery killer doesn't work. thanks
@@fluidmind3629 use NLBA software but it’s not free
@@mihaigsm100 no cp2112 support ?
@@mihaigsm100 does it support cp2112 ?
I can't unseal my battery how to fix it. Error unseal
U have license for DJI?
@@mihaigsm2003 yes i have sir
@@sengchatsangma8811 contact ubrt
The software need licensing?
sure
i have interface ev2300
hello my friend how can ı fix battery authendication failed
after ubrt my battery work but cant start motor and say battery authendication failed ( mavic pro phantom 4)
@@salihcengizesmer8467 this is common problem for Ubrt and similar software, it does not clear PF correctly
the software is a demo version
Need to pay for license
i subscribe
Adapter cp2112 👍2.50$ or programmator 100$ and licence ubrt 200$🤬👎.and programm dji battary killer.exe
ola amigo voce tem o programa ?
@@atylasouza8151 есть программа скачанная с форума и бесплатная, у меня она есть, только не знаю как отправить файл. Напиши мне адрес куда отправить dji battary killer
@@atylasouza8151 there is a program downloaded from the forum and free, I have it, but I don’t know how to send the file. Write me the address where to send the dji battary killer