I have an issue with steam pressure. Temperature of the steam boiler is ok (around 135-145c) but I am not getting much pressure. My Lelit Elizabeth is 1 month old, steam wand holes are not clogged, steam boiled is refiling without issues, but I am not getting steam high enough to froth a milk. This issue that I am getting stated to appear one week ago. Do you have some suggestion where to look for. Thanks
@@lelitinsider2977 Hi, I did what you suggested and Lelit kindly replayed and said what could be the issue, but with little research, the tap pin was the issue(2200075), teflon worn out , I replaced it and now I have much better steam pressure. But I am facing different problem now with steam pressure. I set steam to 145C, while steaming 150ml of milk, temperature rapidly dropped to 124C but boiler heating element did not turned on to heat up the water to set temp(145C). It passed 1 minute and then heating element started heating water to 145C. I did a test to see to what temperature water needs to drop in order for PID to automatically turn heating element. This temperature was 118C. Can you tell me if this is the right behaviour, I think that PID should turn on a heating element way before 118C. Thanks a lot.
@@lelitinsider2977 Thanks for the suggestion, apparently this is not happening when steam boiler temp is set to 135C. Heating element is almost instantly turned on if temperature drops below 135C(133C heating element trigger temp, but can not build up temperature back to 135C if I do not stop steaming, then when I stop at 116C then it turns boiler refill and then goes back to 135C. When boiler is set to 135C it is very difficult to steam 150ml of milk, losses pressure quite fast. From 135 to 130C in 5 sec). Also coffee boiler temp is fluctuating quite a lot, set temp is 95C and it drops to 89C and then rises to 104-110C and then drops to 93C or to 89C again, it depends. Do you have any other suggestion or do you know what is the issue. Thanks a lot for helping me to try troubleshoot what is the issue. All the best
Hi, so the problem in this situation is the sonda??? I hace machine with presostato and safety termostat... And sometimes the boiler stop to heating.. I decided change valvols antidepressione because loss steam... and change safety termostato. For now work well.. But you have any coment?? Thanksss
@@lelitinsider2977 in my case... maybe yes... Because when push bottom of safety thernostat, the resistance go heating. Also this problem, It is since work normaly... and time after less temperature, but and when open steam valve the machine less all pressure (in the manometer) I don’t know with totaly securitt if this is the problem and the solution but in this case... it seems solve
@@lelitinsider2977 inthis case, no In other machine with sinilar proboem i changed for a new pressostat but I didnt have good results... So, in this case I change just safety termodtat and valvole antidepressione because no blocking well and loss steam here
I have an issue with steam pressure. Temperature of the steam boiler is ok (around 135-145c) but I am not getting much pressure. My Lelit Elizabeth is 1 month old, steam wand holes are not clogged, steam boiled is refiling without issues, but I am not getting steam high enough to froth a milk. This issue that I am getting stated to appear one week ago. Do you have some suggestion where to look for. Thanks
Hi, please send an email at care@lelit.com and please send us the serial number foto of your elizabeth
@@lelitinsider2977 Hi, I did what you suggested and Lelit kindly replayed and said what could be the issue, but with little research, the tap pin was the issue(2200075), teflon worn out , I replaced it and now I have much better steam pressure.
But I am facing different problem now with steam pressure. I set steam to 145C, while steaming 150ml of milk, temperature rapidly dropped to 124C but boiler heating element did not turned on to heat up the water to set temp(145C). It passed 1 minute and then heating element started heating water to 145C. I did a test to see to what temperature water needs to drop in order for PID to automatically turn heating element. This temperature was 118C. Can you tell me if this is the right behaviour, I think that PID should turn on a heating element way before 118C.
Thanks a lot.
@@nemanjatalijan hi try to set the steam temperature at a lower value, example 135°-138, and tell me if happends again
@@lelitinsider2977
Thanks for the suggestion, apparently this is not happening when steam boiler temp is set to 135C. Heating element is almost instantly turned on if temperature drops below 135C(133C heating element trigger temp, but can not build up temperature back to 135C if I do not stop steaming, then when I stop at 116C then it turns boiler refill and then goes back to 135C. When boiler is set to 135C it is very difficult to steam 150ml of milk, losses pressure quite fast. From 135 to 130C in 5 sec).
Also coffee boiler temp is fluctuating quite a lot, set temp is 95C and it drops to 89C and then rises to 104-110C and then drops to 93C or to 89C again, it depends.
Do you have any other suggestion or do you know what is the issue.
Thanks a lot for helping me to try troubleshoot what is the issue. All the best
@@nemanjatalijan please cek your ec value, and if is 5 change it with 0
as in this video ruclips.net/video/rR4b6w9iOfs/видео.html
What is the thing that surrounds the steam boiler (black and white) I would like to know the name so that I can order it thank you
thermal insulation for boiler
@@achitofernandez2570 thanks brother. Do you a link to buy it
Hi, so the problem in this situation is the sonda???
I hace machine with presostato and safety termostat...
And sometimes the boiler stop to heating..
I decided change valvols antidepressione because loss steam... and change safety termostato. For now work well..
But you have any coment?? Thanksss
hi, when the heating doesn't work, is the safety thermostat activated?
@@lelitinsider2977 in my case... maybe yes...
Because when push bottom of safety thernostat, the resistance go heating.
Also this problem, It is since work normaly... and time after less temperature, but and when open steam valve the machine less all pressure (in the manometer)
I don’t know with totaly securitt if this is the problem and the solution but in this case... it seems solve
@@achitofernandez2570 hi have you changed the pressostat?
@@lelitinsider2977 inthis case, no
In other machine with sinilar proboem i changed for a new pressostat but I didnt have good results...
So, in this case I change just safety termodtat and valvole antidepressione because no blocking well and loss steam here
What is the thing that surrounds the steam boiler (black and white) I would like to know the name so that I can order it thank you
Ciao, ho appena aperto una Kate, si accende perfettamente ma non eroga ne caffè, ne acqua me vapore