Bedan Practice #2

Поделиться
HTML-код
  • Опубликовано: 30 окт 2024

Комментарии • 16

  • @jackofalltrades7822
    @jackofalltrades7822 9 лет назад

    I just watched another video where the guy has the Bedan upside down for the way you are using it to cut tenons.
    Why would that be?
    Pretty sure he is experienced as he was doing a demo for a group. Please help...

  • @petesutton4199
    @petesutton4199 9 месяцев назад

    I would love to buy a similar tool, where in the uk or France ? Pete

  • @tvogel1810
    @tvogel1810 2 года назад

    Thank you - saved this vid

  • @bobham5
    @bobham5 14 лет назад

    I was tempted to grind off the corners of the shaft but I was concerned about what would happen when I eventually ground the tool back that far. Have you reached that stage yet?
    Thanks
    Bob

  • @laetitiakastar
    @laetitiakastar 17 лет назад

    Thanks for sharing! Do you have a video about using the bedan on endgrain?

  • @TokyoCraftsman
    @TokyoCraftsman  14 лет назад

    @StuInTokyo .....cont.....
    When you do finally reach the rounded off corners, then buy a new bedan, but don't toss the old one, just regrind it into a square scraper or a large parting tool.
    I hope this helps.
    Cheers!

  • @TokyoCraftsman
    @TokyoCraftsman  14 лет назад +1

    Hi Bob, sorry for being so late to reply.
    I asked Jean Francois Escoulen the same question, and he told me not to worry about it, the Bedan is a tool that does not nee a lot of sharpening, and when you do sharpen it, you use the hone most of the time, so if you do not remove a lot of material each time you hone the bedan, then it will last for many many years..... cont

  • @Paxter10
    @Paxter10 16 лет назад

    Well done, very impressive

  • @BipolarBowler
    @BipolarBowler 8 лет назад

    Do you have a micro bevel on that tool? I notice a shiny line right before the cutting edge

    • @TokyoCraftsman
      @TokyoCraftsman  8 лет назад

      +BipolarBowler not really a micro bevel, that area is honed on the power hone, all one angle.
      Domo

  • @pauljschuetz
    @pauljschuetz 12 лет назад +1

    i really like the cuts it makes where could i get my hands on one

  • @bobham5
    @bobham5 14 лет назад

    Hi, Stu:
    I see that you have relieved the bottom corners of the shaft of the tool to allow it to slide and roll better on the tool rest. What happens when you have sharpened it enough time that you get back to that area with the cutting edge? Won't that mean you will lose the corners of the cutting edge? I just tried a bedan for the first time today and found the sharp corners of the shaft really dragged and bit in to the tool rest when I tried to roll and traverse. (continued)

  • @TokyoCraftsman
    @TokyoCraftsman  17 лет назад

    Sorry, but the Bedan is, as far as I know, NOT used on end-grain, it is a spindle turning tool.
    Cheers!

  • @CharlesStanford-y7g
    @CharlesStanford-y7g 3 месяца назад

    Your mortise chisel is basically the same tool.

    • @TokyoCraftsman
      @TokyoCraftsman  3 месяца назад

      Gonna have to disagree 😁

    • @CharlesStanford-y7g
      @CharlesStanford-y7g 3 месяца назад

      @@TokyoCraftsman The way you have it set up, it looks like a mortise chisel.