I had my washer disconnected for months and it didn't want to work and this video got it working again. Thank you!! I'm happy I didn't have to call a repair man or customer support. For me, the lid lock light would be on so I left it open and the steps still worked.
I just found this video and the process is running as we speak. Praying this does the trick. The washing machine also hasn't been used or even plugged up in months🎉 Btw, it responded exactly like the video described ❤❤❤
My husband has fixed this washer 3 times already. Worse purchase ever, only 3 years old. Hopefully last a couple more months. But your video so helpful to reset it.
Cheers from PR. Thanku 4 your video. I reprogramed my Whirpool washer like u said. I think the problem was voltage fluctuations. At this moment its working fine. My wife and are happy.
Man if it weren’t for you posting the video I would have been without my washing machine until the service guy came back!! He’s been here twice doing repairs on my 2 month old 2-1 whirlpool. Apparently the bearings within the transmission was bad so he replaced the entire thing.. so far I am not happy with this washer.. thank you so much for doing what the repair man should have done while he was here.
Ran a clean cycle...didn't think much about it...loaded up with clothes the next day, put soap in and everything....nope....dug everything darn thing back out...reset and so far so good, although the washer didn't run a 45 minute reset more like 1 minute. I'm thankful for this video, but I'm sad I don't have my 30 year old washer anymore. Thank you for the tips!!!! Before I forget, this is 7 months old, I have already had a service call, and I've had to reset it a few times. I'm glad I bought that 5 year warranty cause it looks like we are gonna need it 😅
This video saved my bacon. My asking machine isn't exactly like the one in this video, but it is close. There are only 5 buttons on the right, but I figured out the sequence and now my washer is up and running. Thank you!
Thank you! This really helped. Ours died after a power surge from power restoration after a storm. My daughter was washing during the storm and it wouldn't work after the power came back on. All the top lights were on and I couldn't get your reset method to work, so we decided to unload the clothes so I could drain it like you said. As soon as we unloaded, it started draining on its own! Crazy. I was able to to run your reset sequence afterwards (to be safe) and it's back to functioning as it should! Thank you again for the help! 👍 I was afraid our two year old machine was going to be expensive to fix. 😮
this video was very helpful my wife and i are very greatful we been without a washer for months and we didn't know what do so again thank you for the help
Thank you so much for this video! Bought my washer in April, it died in June. Repaired 4 days go and I got to do 5 loads before the lid stopped locking! I was so excited that my washer did exactly what your video shows for the reset, locking and unlocking as you outlined. However, when I went to try a load, the lid would not lock. Oh well, back to the Whirlpool warranty repair part 2.
Thanks, I looked the code up and you are correct. The 6th wash load became unbalanced and was washer bucking so hard I thought it would hit a wall. The only thing I could think to do was press the start button to stop it. The lid unlocked then, but after reset, the lid clicks on/off immediately when I try to start a cycle. I am not smart enough to enter more codes - old lady who used to fix balance by opening a lid with no lock (Kenmore 1986 and still working like a champ) and moving the laundry around. I will have wait for the technician and hope for a quick. @@JosephGordon-ny6eb
My washer started bucking real bad once it stoped the clothes was still a little bit wet took the clothes out but the washer didn't want to work i tried the everything in the video but nothing, the light turns on but it just makes the locking noise but it don't lock
Worked perfectly after I replaced the lid lock. Which by the way instead of taking the entire wire off I only popped off the lod lock , flipped it over and removed the smallest backing piece and pushed plugged off of the board and then slid the plug on to the replacement lid lock unit and re installed. Took less than ten minutes and I by passed alot of work.
What lights were flashing in your washer? I’m trying to decipher my code. I have been unsuccessful. Mine flashes sense done and lock then it flashes just done. We replaced drain pump noticed a spliced burnt wire and I 🎉 thinking yes!! But no 😢. I don’t want to keep buying parts I’m not rich or I would have taken this washer over to whirlpool lit it on fire and gave them the finger. 16 months and this is what I get for buying new
Wish they made washers like they use to. New Maytag washer didn’t even make it pass its first wash. GE washer needs transmission and bearings replaced after only 5 months. Front loaders don’t use enough water to actually clean clothes. Have to hack/modify a screw on water level sensor unit to fill with more water. All junk.
@@Ikey04-ge9gy😂 ngl I died laughing at this! What would a conversation about laundry pertain, that someone couldn't be ready for? It's either enough or not 😂
Because so many people are still attached to their ancient dinosaur top loaders that guzzle resources just to give an average clean. They’re stuck to the idea front loads clean worse because of less water but that couldn’t be any farther from th truth
I get to the last step (where you said it took about 4 min to finish), but it just continually flashes from Sense -> Soak -> Wash -> Done. It did that from 5:30pm Sunday until 6:30am Monday morning, so I redid it again. What should I do if it doesn't finish recalibrating?
Did either of you guys ever find a solution because this isn't happening to mine? I haven't even had it that long. I replaced the locking mechanism because it stopped working and now I can't get it to work. Soak wash done in lid lock
@@cheryldaves7107 No. The solution was buying a new washing machine. Continually had too many issues with this one, and got tired of throwing money into it.
I appreciate the information the reset did not work. The lights soak, wash and done Keep flashing well after four minutes. I keep seeing comments about error codes. Where are the error codes displayed on the panel? My washer is not even two years old.
@@briancartagena9749he has another video. Hit 123 buttons in order 3 times, then it will alternate flashing the 4 top lights if error code. One with the lid lock light on, the other with out it on. The pattern coordinates to a number. I think first was an F code, the second an E code.
How long did it take for the full recalibration to complete? In the video he said it would take "quite some time" but the lights on the washer have been flashing about an hour now. Can you help?
I did the reset thinking that was the reason the lid would not latch. Did not work to cause the latch to work but all of the other things happened - the lights flashed and the machine ran. I figured there was an issue with the latch itself. So I unscrewed the latch from the lid and placed it into the latch mechanism. It latched and it appears it has to do with how the latch enters the latch mechanism. For now it works.
@bensappliancesandjunk thank you so much for your video! I had a similar problem with my dryer and there are no videos of this style of dryer. So, I followed your directions to the washer and was able to figure out that my sensory board was loose. I was able to fix it in 10 mins! Thank you! Thank you!
Hi did this to mine and went through an initial start up qoth some water being dispensed. Then the sense, done and Lid buttons blink once, and the Done light blunk byitself a second later. Repeats this patter every 4 seconds.Seems stuck in pattern. Any ideas what i should do?
I wasn't even given instructions on how to use my washer. so confusing how to get it to even start. do you have a video for that? it's not filling so I'm not sure I am doing it right
I've now gone through 2 whirlpool washers in a month. Why do you need a course to get ypur washing machine to work as it should? Any idea? Lol You pretty much need to take a course just to wash clothes? The world has gotten way too weird and I'm someone who's been into computers since 1982 and very comfortable with electronics. 😮😂 Are there new models without this headache? A huge thank you for making and posting this video. ❤
My whirlpool had an error code F7E1 and I replaced the shift actuator like everyone said, still didnt spin. I replaced the capacitor and its working again so I recalibrated and its going fine. Thanks for the video!
@jromyn it sounds goofy but I searched whirlpool washer capacitor on eBay and found a bunch that look like the one on my machine. I made sure the one I bought said brand new. It was easy to swap out and I haven't had a problem since.
I have a different style washer but it comes on but when I tap the button it beeps twice with no response I unplug it and the lights stay on for a min and replug same thing. It has not agitator
thanks for this video, unfortunately it didn't work for me. did 16 loads in my Whirlpool and it die. after waiting two and a half weeks the service company came out, and when I went to do laundry a few days later it's still wasn't working. My last washer lasted almost 20 years. this one didn't even last 20 weeks
Hello. I have Maytag 4.8 cf top load with deep fill. All light turn on with sense blink. It can not even shut off when I try shut down. When I hold start all the light turn on from left to right then begin like the first I mentioned. What should I do now and what do you think?
Any help on resetting a washer that was mid wash, full of water when our power went out? The energy company restored power within an hour but now the power buttons are just stuck.
New machine, (like yours) trying to use first time, wouldn't fill. Directions said it should fill with allfresh (cleaning cycle). It said I could pause or stop. At half full I tried both pause and stop, machine wouldn't respond. I unplugged and plugged back in. Door would never unlock, machine went into drain mode, when finished draining, finally unlocked, now water temp flashes between warm and hot but 'whirlpool model # WTW5057LWO won't do anything except the H/W light flash. Seller says since they didn't do the install (blah blah, excuse, excuse). My previous washer, a Whirlpool, lasted over 50 years, ONLY thing I ever did to it was replace the belt. Thoughts?
Hi Ben. I did all the diagnostic steps. Everything was okay, except right after all the steps, my machine just kept draining. Agitator not spinning, too. Any idea? The blinking lights are sense, done, lid, and then just done. Pause for a little bit, and the draining starts again.
mine won't get past the sense part when you turn it on. does sense and then goes to done. any ideas. no spinning, only slight movement when reset and water comes out.
MVW6200KW1 only flashes sensing. Replaced the cpu/mainboard. Only sensing light comes on plus led indicators for temp , load size and etc. When i attempt to enter fault codes mode all indicators only flash once. (I understand they should flash twice if entered successfully. ) Then wash, rinse/spin, done and lid flash once then rinse/spin and done flashs once. Repeats. Removed back panel i see green flashing thru epoxy in bottom of board. Blue led on back of board remains off. Any help is appreciated. 3:20
What if the washer has clothes and water inside? Our washing machine automatically locked but the light of the lid is not there. It won't go to the soak, wash and done. It just stays in Sense mode. 😢
Ok Ben, got one for you. Why would a Maytag front load give an f05 error, even after replacing the components, heating element, heat sensor and ccu? Got any ideas?
@nenenene9744 so if you wash with warm or hot water, you'll be able to finish your cycle if you're in a pinch. Check your water inlet valve to see if there is any debris. Disconnect the washer power supply, shut water supply off from the washer, remove cold water supply hose, and just look at the valve. If there's debris, it either needs to be cleaned or replaced. That's where I'm at right now I sprayed compressed air into the valve and got my washer dispensing more cold water but it's not enough for a cycle. My next step is to remove it, clean it and see if it works.
One question though at the end of the reset when you do everything you have to do how long should I be waiting for the blinking to stop? You said it took about 4 minutes for you but it’s taking longer then 4 minutes for me.
My xpert system has 3 knobs and a start button and a power button that's it , how do I recalibrate this type, washing filling and tripping out when to start wash
My washer lid switch was replaced and i done this it started fine then went to flashing sense done lid lock all at same time in middle of calibration mode. Please help😢
@@johnlucian2259 The belt had ended up coming off of the bin's pulley! I tipped it on its side, pulled the cover, and popped the belt back on. No issues since👍
What to do . .afterive completed steps to reset, the soak ,wash, done, lights flash in sequence then the lid light flashes and it repeats. Leaving me no way to open lid to complete last step. What to do?
Thanks for the video Ben. What happens if the washing machine doesn't respond pass the initial 1-2-1-2? I've verified that it is receiving power properly.
Took me a few times to get this to work. May have to unplug, wait 1min, then plug back in. Make sure the dial can work and you can select things too in a separate test
Ben, my issue I cannot empty the water in the unity prior going thru the reset process. Any suggestions??? I did run thru the process with water in the unit and it did not resolve the issue. Thanks for your support!
I got a question for the professionals ! I have several washers that once you hit the “start” button , it waits about 5 minutes then it will start filling with water . Can someone help point me in the right direction because we have others just like it and the water fills as soon as you press start. It’s a whirlpool with the 6 led lights
If you cant get this to work try checking the wires going to the motor. Mine just kept flashing for hours when i tried this. Turned out a wire had rubbed through and was arching
I replaced my locking mechanism. (It broke while it was locked my wife forced it opened and broke it. I’ve replaced it tried to rest the washer but it won’t lock. It’s giving me a error code F5E3. Any help?
I didn't know I would live to see the day that I would have to outsmart a washing machine but here we are. Thank you for this troubleshoot tip!
I had my washer disconnected for months and it didn't want to work and this video got it working again. Thank you!! I'm happy I didn't have to call a repair man or customer support. For me, the lid lock light would be on so I left it open and the steps still worked.
I just found this video and the process is running as we speak. Praying this does the trick. The washing machine also hasn't been used or even plugged up in months🎉 Btw, it responded exactly like the video described ❤❤❤
My husband has fixed this washer 3 times already. Worse purchase ever, only 3 years old. Hopefully last a couple more months. But your video so helpful to reset it.
You were the only one that had a video for my washer. I’m sooooooooooo thankful! So far it’s going through a washer cycle. I thank you!🎉
Cheers from PR. Thanku 4 your video. I reprogramed my Whirpool washer like u said. I think the problem was voltage fluctuations. At this moment its working fine. My wife and are happy.
Man if it weren’t for you posting the video I would have been without my washing machine until the service guy came back!! He’s been here twice doing repairs on my 2 month old 2-1 whirlpool. Apparently the bearings within the transmission was bad so he replaced the entire thing.. so far I am not happy with this washer.. thank you so much for doing what the repair man should have done while he was here.
This was the most helpful video ever. I hate modern technology because when it goes wrong it’s nearly impossible to repair yourself. Thank you!!!!!
Wow! Ben, you're the best thing that has ever happened to 'DIY' appliance videos...
Ran a clean cycle...didn't think much about it...loaded up with clothes the next day, put soap in and everything....nope....dug everything darn thing back out...reset and so far so good, although the washer didn't run a 45 minute reset more like 1 minute. I'm thankful for this video, but I'm sad I don't have my 30 year old washer anymore. Thank you for the tips!!!! Before I forget, this is 7 months old, I have already had a service call, and I've had to reset it a few times. I'm glad I bought that 5 year warranty cause it looks like we are gonna need it 😅
Really wish I bought the extended warranty.
@Artimidorus we did and it's useless
This video saved my bacon. My asking machine isn't exactly like the one in this video, but it is close. There are only 5 buttons on the right, but I figured out the sequence and now my washer is up and running. Thank you!
Thank you! This really helped. Ours died after a power surge from power restoration after a storm. My daughter was washing during the storm and it wouldn't work after the power came back on. All the top lights were on and I couldn't get your reset method to work, so we decided to unload the clothes so I could drain it like you said. As soon as we unloaded, it started draining on its own! Crazy. I was able to to run your reset sequence afterwards (to be safe) and it's back to functioning as it should! Thank you again for the help! 👍 I was afraid our two year old machine was going to be expensive to fix. 😮
this video was very helpful my wife and i are very greatful we been without a washer for months and we didn't know what do so again thank you for the help
Thank you so much for this video! Bought my washer in April, it died in June. Repaired 4 days go and I got to do 5 loads before the lid stopped locking! I was so excited that my washer did exactly what your video shows for the reset, locking and unlocking as you outlined. However, when I went to try a load, the lid would not lock. Oh well, back to the Whirlpool warranty repair part 2.
5160
Thanks, I looked the code up and you are correct. The 6th wash load became unbalanced and was washer bucking so hard I thought it would hit a wall. The only thing I could think to do was press the start button to stop it. The lid unlocked then, but after reset, the lid clicks on/off immediately when I try to start a cycle. I am not smart enough to enter more codes - old lady who used to fix balance by opening a lid with no lock (Kenmore 1986 and still working like a champ) and moving the laundry around. I will have wait for the technician and hope for a quick. @@JosephGordon-ny6eb
@JosephGordon how do you put those codes in
My washer started bucking real bad once it stoped the clothes was still a little bit wet took the clothes out but the washer didn't want to work i tried the everything in the video but nothing, the light turns on but it just makes the locking noise but it don't lock
Worked perfectly after I replaced the lid lock. Which by the way instead of taking the entire wire off I only popped off the lod lock , flipped it over and removed the smallest backing piece and pushed plugged off of the board and then slid the plug on to the replacement lid lock unit and re installed. Took less than ten minutes and I by passed alot of work.
do you mean the white part of the lid lock, that little white plastic piece?
hey @yashuwbyisrael2324 i need a video from you
What lights were flashing in your washer? I’m trying to decipher my code. I have been unsuccessful. Mine flashes sense done and lock then it flashes just done. We replaced drain pump noticed a spliced burnt wire and I 🎉 thinking yes!! But no 😢. I don’t want to keep buying parts I’m not rich or I would have taken this washer over to whirlpool lit it on fire and gave them the finger. 16 months and this is what I get for buying new
Thank You. I had to completely drain the washer, It's now working after following your instructions.
Thanks!
I just reset my washer from looking at your video thank you so much
I like how the control panel sinks in when pressing the buttons.
Wish they made washers like they use to. New Maytag washer didn’t even make it pass its first wash. GE washer needs transmission and bearings replaced after only 5 months. Front loaders don’t use enough water to actually clean clothes. Have to hack/modify a screw on water level sensor unit to fill with more water. All junk.
it is illegal to make washers like they used to. thank your government.
Front loader do use enough water and clean better than any top loader. But that’s a conversation you guys aren’t ready for.
Amen!
@@Ikey04-ge9gy😂 ngl I died laughing at this! What would a conversation about laundry pertain, that someone couldn't be ready for? It's either enough or not 😂
Because so many people are still attached to their ancient dinosaur top loaders that guzzle resources just to give an average clean. They’re stuck to the idea front loads clean worse because of less water but that couldn’t be any farther from th truth
This one looks quite familiar
I would pay for phone service with this guy
We are going to do that soon!
I get to the last step (where you said it took about 4 min to finish), but it just continually flashes from Sense -> Soak -> Wash -> Done. It did that from 5:30pm Sunday until 6:30am Monday morning, so I redid it again. What should I do if it doesn't finish recalibrating?
Mines doing the same thing, stuck with the flashing for over 12 hours. I'm trying it again. Did you find a solution?
Did either of you guys ever find a solution because this isn't happening to mine? I haven't even had it that long. I replaced the locking mechanism because it stopped working and now I can't get it to work. Soak wash done in lid lock
Look underneath at the wires going to motor. Mine has a wire that rubbed through and was arcing causing it to not spin
@@cheryldaves7107 No. The solution was buying a new washing machine. Continually had too many issues with this one, and got tired of throwing money into it.
@chrismigl8763 yes I ended up getting a new one as well. What a waste of money. I didn't even have it a year.
I'm dealing with this exact unit, not even ran 10 loads total, pretty fresh purchase. I miss the old unit
I appreciate the information the reset did not work. The lights soak, wash and done Keep flashing well after four minutes. I keep seeing comments about error codes. Where are the error codes displayed on the panel? My washer is not even two years old.
Having the same problem with mine. 2 years old. Did you find a solution?
@@briancartagena9749he has another video. Hit 123 buttons in order 3 times, then it will alternate flashing the 4 top lights if error code. One with the lid lock light on, the other with out it on. The pattern coordinates to a number. I think first was an F code, the second an E code.
Thank you so much I was really going to cry. I thought I had broken another washing machine
Great
Video and very helpful… it’s a shame everythjng these days has to be so confusing
How long did it take for the full recalibration to complete? In the video he said it would take "quite some time" but the lights on the washer have been flashing about an hour now. Can you help?
Thanks, had to install water inlet valve and needed to reset it before I started it
I did the reset thinking that was the reason the lid would not latch. Did not work to cause the latch to work but all of the other things happened - the lights flashed and the machine ran. I figured there was an issue with the latch itself. So I unscrewed the latch from the lid and placed it into the latch mechanism. It latched and it appears it has to do with how the latch enters the latch mechanism. For now it works.
@bensappliancesandjunk thank you so much for your video! I had a similar problem with my dryer and there are no videos of this style of dryer. So, I followed your directions to the washer and was able to figure out that my sensory board was loose. I was able to fix it in 10 mins! Thank you! Thank you!
Nice!
Wooow thank you so much! It’s doing something finally!!! You are a complete genius!
So what did he say to do? Mine has been blinking for a while now…
What does it mean when I follow all of the rest steps but the machine makes a grinding noise right before it goes into its cycle and doesnt start?
God bless you!!!! So save my life several times😆😃
Thank you for this video. My washer had stopped mid wash, and this reset worked. 😊
Hi did this to mine and went through an initial start up qoth some water being dispensed. Then the sense, done and Lid buttons blink once, and the Done light blunk byitself a second later. Repeats this patter every 4 seconds.Seems stuck in pattern. Any ideas what i should do?
I wasn't even given instructions on how to use my washer. so confusing how to get it to even start. do you have a video for that? it's not filling so I'm not sure I am doing it right
I've now gone through 2 whirlpool washers in a month. Why do you need a course to get ypur washing machine to work as it should? Any idea? Lol You pretty much need to take a course just to wash clothes? The world has gotten way too weird and I'm someone who's been into computers since 1982 and very comfortable with electronics. 😮😂
Are there new models without this headache?
A huge thank you for making and posting this video. ❤
That was extremely helpful. Why would a product like this fail after only 6 months?
My whirlpool had an error code F7E1 and I replaced the shift actuator like everyone said, still didnt spin. I replaced the capacitor and its working again so I recalibrated and its going fine. Thanks for the video!
Which capacitor? I have a similar problem...just replaced actuator and I'm still get the F7E1 error code after doing a reset.
@jromyn it sounds goofy but I searched whirlpool washer capacitor on eBay and found a bunch that look like the one on my machine. I made sure the one I bought said brand new. It was easy to swap out and I haven't had a problem since.
Thank you so much! This fixed my washer!!! You saved me a lot of money!
Glad I could help!
What about the MVW5430MW0?
Thank you so much for this video.
I have a different style washer but it comes on but when I tap the button it beeps twice with no response I unplug it and the lights stay on for a min and replug same thing. It has not agitator
Just did this hope it works!
My washer model MVWB765FW3 won't put water in the tub (hot or cold) we have cold and hot water in the lines.
Is this procedure the same for WTW8900BC whirlpool cabrio platinum?
how long do you think the reset lasts?
thanks for this video, unfortunately it didn't work for me. did 16 loads in my Whirlpool and it die. after waiting two and a half weeks the service company came out, and when I went to do laundry a few days later it's still wasn't working. My last washer lasted almost 20 years. this one didn't even last 20 weeks
Hello. I have Maytag 4.8 cf top load with deep fill. All light turn on with sense blink. It can not even shut off when I try shut down. When I hold start all the light turn on from left to right then begin like the first I mentioned. What should I do now and what do you think?
Needed you again ben,thank you
Thank you. Just what I needed!!
Any help on resetting a washer that was mid wash, full of water when our power went out? The energy company restored power within an hour but now the power buttons are just stuck.
Maytag top load washer MVW6200KW. It goes from sensing and skips to done. The inside won’t spin while balancing the load
Sooo what do you do if the lights are flashing before you can start the process then?
What happens if you washer does not lock to start the process
I have the dryer version of this whirlpool what is next after I hit all the buttons to turn off the lights since a dryer lid doesn't lock?
Thankyou! From the bottom of my heart! I'm going to subscribe...
New machine, (like yours) trying to use first time, wouldn't fill. Directions said it should fill with allfresh (cleaning cycle). It said I could pause or stop. At half full I tried both pause and stop, machine wouldn't respond. I unplugged and plugged back in. Door would never unlock, machine went into drain mode, when finished draining, finally unlocked, now water temp flashes between warm and hot but 'whirlpool model # WTW5057LWO won't do anything except the H/W light flash. Seller says since they didn't do the install (blah blah, excuse, excuse). My previous washer, a Whirlpool, lasted over 50 years, ONLY thing I ever did to it was replace the belt. Thoughts?
Once the cycle stopped, my washer still made a weird noise and wouldn’t go through a wash cycle. Any tips?
Hi Ben. I did all the diagnostic steps. Everything was okay, except right after all the steps, my machine just kept draining. Agitator not spinning, too. Any idea? The blinking lights are sense, done, lid, and then just done. Pause for a little bit, and the draining starts again.
Did you ever find a solution?
very interested if a solution was found
mine won't get past the sense part when you turn it on. does sense and then goes to done. any ideas. no spinning, only slight movement when reset and water comes out.
What would you do if during the calibration the drum never spinned?
Look for error codes. I have a video for that
MVW6200KW1 only flashes sensing. Replaced the cpu/mainboard. Only sensing light comes on plus led indicators for temp , load size and etc. When i attempt to enter fault codes mode all indicators only flash once. (I understand they should flash twice if entered successfully. ) Then wash, rinse/spin, done and lid flash once then rinse/spin and done flashs once. Repeats.
Removed back panel i see green flashing thru epoxy in bottom of board. Blue led on back of board remains off. Any help is appreciated. 3:20
Shouldnt blue led on board be lit?
What do you do if the tub has clothes and water in it, and it is stuck with locked lid and flashing lights even after unplugging?
Thank you so much it worked!
Thank you
So my washer will go right from sensing to done. And won't spin when sensing...could it be a motor or belt?
Will these instructions work for a Maytag 2000 Series washer? Model MHWE251YG00 Front Load 3.5 cu.ft. 27" stackable washing machine?
Unless the UI is identical, no
Thank you for the information easy peasy
Hello I changed the actuator and it’s still not spinning. I don’t know what else it could be.
What if the washer has clothes and water inside? Our washing machine automatically locked but the light of the lid is not there. It won't go to the soak, wash and done. It just stays in Sense mode. 😢
I have the same issue 😩
Ok Ben, got one for you. Why would a Maytag front load give an f05 error, even after replacing the components, heating element, heat sensor and ccu?
Got any ideas?
Check wires for damage
Washer drain stays on in any cycle, currently getting error F3E2 but the hose is not bad
After all that my washer keeps flashing sense, Done, lid locked. Should I try again?
Did u figure out what it was that's where I'm at? It's driving me crazy
I'm also having this issue. What temp water are you running?
I'm trying to wash in cold water.
Wash cold water
@nenenene9744 so if you wash with warm or hot water, you'll be able to finish your cycle if you're in a pinch.
Check your water inlet valve to see if there is any debris. Disconnect the washer power supply, shut water supply off from the washer, remove cold water supply hose, and just look at the valve. If there's debris, it either needs to be cleaned or replaced. That's where I'm at right now I sprayed compressed air into the valve and got my washer dispensing more cold water but it's not enough for a cycle.
My next step is to remove it, clean it and see if it works.
Good to know.
One question though at the end of the reset when you do everything you have to do how long should I be waiting for the blinking to stop? You said it took about 4 minutes for you but it’s taking longer then 4 minutes for me.
I’m currently resetting mine as well. Lights blinking for a very long time.
same@@jsg1108
How long did it take to stop?
Thank You- excellence
My xpert system has 3 knobs and a start button and a power button that's it , how do I recalibrate this type, washing filling and tripping out when to start wash
Thank you so very much !!!!! Thank you!
What happens if there is water in the tub? It stopped , never emptied and now I want to reset?
Me too!!!!
Did y’all ever find a way to fix this? We have had this washer for 5 months and now it won’t drain or even attempt to drain
My washer lid switch was replaced and i done this it started fine then went to flashing sense done lid lock all at same time in middle of calibration mode. Please help😢
Any chance you could help with/do a video on this model with an F7E1 no spin error?
did you get your issue fixed
what was it
@@johnlucian2259 The belt had ended up coming off of the bin's pulley! I tipped it on its side, pulled the cover, and popped the belt back on. No issues since👍
What to do . .afterive completed steps to reset, the soak ,wash, done, lights flash in sequence then the lid light flashes and it repeats. Leaving me no way to open lid to complete last step. What to do?
My lid wont lock is there another step i can take?
It worked thanks
Thanks for the video Ben. What happens if the washing machine doesn't respond pass the initial 1-2-1-2? I've verified that it is receiving power properly.
Took me a few times to get this to work. May have to unplug, wait 1min, then plug back in. Make sure the dial can work and you can select things too in a separate test
@@bensappliancesandjunk Thanks, I'll keep trying!
Ben, my issue I cannot empty the water in the unity prior going thru the reset process. Any suggestions??? I did run thru the process with water in the unit and it did not resolve the issue. Thanks for your support!
I have the same problem
I did a reset on my washer. everything worked except no spin action in there
What happens if the lights don't come on? But the faucet starts to fill with water?
What happens if your machine starts sensing then goes to done but never starts a load
The error code f7e4 appeared during the recalibrate mode. Any suggestions?
No matter what wash i try It locks and unlocks, does 2 half spins, makes a noise, then says done.
Mine is doing the same thing, any suggestions?
Machine is out of balance. Unplug the machine, plug it back in. Go to drain and spin cycle, then process to whatever wash cycle you normally use.
It says to have no water in tub. What must I do when I have water in tub?
Nice video , these washers suck tho . Always something going wrong
Thanks brother
Do you have any used Whirlpool washers for sale? I'm interested in getting one, and how much will it cost to ship to the Caribbean?
It's going to cost more than the washer
@@bensappliancesandjunk 👍👍👍.
Mine does have the green light but it won’t spin after the recalibration it will do the rinse but then not spin any idea what it could be?
Possibly capacitor. We just had that issue in a newer one. Check wiring though as well
Ok thanks, do you have a link where I could get one that would fit it. My washer is like the one in your video.
I got a question for the professionals ! I have several washers that once you hit the “start” button , it waits about 5 minutes then it will start filling with water . Can someone help point me in the right direction because we have others just like it and the water fills as soon as you press start. It’s a whirlpool with the 6 led lights
Recalibrate it using whatever method it needs. Often they go out of spec and take too long. That and make sure the water valve screen is cleared.
My washer is showing F7E1 code (tachometer missing or wrong signal) What is a tachometer and how do I fix it?
Shift actuator, I have multiple videos on it for other WP machines.
If you cant get this to work try checking the wires going to the motor. Mine just kept flashing for hours when i tried this. Turned out a wire had rubbed through and was arching
I replaced my locking mechanism. (It broke while it was locked my wife forced it opened and broke it. I’ve replaced it tried to rest the washer but it won’t lock. It’s giving me a error code F5E3. Any help?
I have a whirlpool xpert system and it's only washing on manual cycle , the auto side filling and stopping and won't start washing