The creator should tell the LED must be a RGB, otherwise it nerver flash. if the RGB LED is flashing itself why need the transistor? just connect to the source and 1k resistor.
I think the idea is using the transistor to turn the battery from dc to ac, but I wasn't focusing in the class when the teacher talked about them😅, I think I will have to wait until the college professor talks about it again. If you did under how it's working can you explain 🙂.
Exactly. It's like it's playing a trick on the transistor and it can't make up its mind because of the fluctuating voltage that lets the transistor pass current.
How should I make a circuit to operate for a long time in the form of 12 cat sliding lights with a 9 volt battery? What type of LED should it be? 15 days - 20 days to run (10 hours per day)
Nice setup, just make sure everyone knows that a BMS is REQUIRED for LiIon batteries, to prevent a risk of fire or explosion when those batteries are either charged or discharged beyond their safety threshold.
@@hkhobbypakistan6917 in this circuit you can connect 8 to 10 leds in parallel. Make sure you are connecting the LEDs with the red LED. It will work. You can also use 1k resistor for series (not mandatory) branch.
Dont need these circuit. Just buy a RGB led then connect it with a normal led. It will blink with RGB led. (3.7v) I try his method..... not so bright (2nd led)....
Early Upload!!
For More Information Visit: circuitbest.com
Oke@Ramchandra Mestri yang 2 jam eji
The creator should tell the LED must be a RGB, otherwise it nerver flash. if the RGB LED is flashing itself why need the transistor? just connect to the source and 1k resistor.
For beginners please provide description on its working. Thank you for your contribution
I think the idea is using the transistor to turn the battery from dc to ac, but I wasn't focusing in the class when the teacher talked about them😅, I think I will have to wait until the college professor talks about it again.
If you did under how it's working can you explain 🙂.
would it be possible to replace the red LED and resistor with a relay, if you wanted to make a higher powered lamp flicker?
@@GothGuy885 yes it can be possible
Can i do this with a big light bulb?
Great video! Question:
How would you create a variable strength and variable time difference of the powering and brightness of each LED?
Does it wrk on 9v
can we use another led
Yes ,any
It is work?
Is it possible to input a current of 12v to this?
Can you use alternative transistors ?
Can i make this without rgb led?
Please reply sir.
I have made other video without rgb led
@@Creativecreator please if you can , share me that video link
Because I didn't find that video.
Bro the red light blinks because tricolour_light need more voltage . And it decrease voltage of Red light
Exactly. It's like it's playing a trick on the transistor and it can't make up its mind because of the fluctuating voltage that lets the transistor pass current.
I really like this channel, you are a genius I congratulate you for your good work 😊😍😍
Make video with explanation of the function of the circuit diagrams. i.e. how transistor work ?.
Sorry, there is no similarity between the thumbnail and the video. Please don't misguide only for watch time.
Nice project. If I want to use 12voltage battery, what changes needed to be done in the circuit?
I have made a dedicated video on that
Can you complete this using only 1k resistors?
Does the base really need an extra led?
Can i use 9V supply
How long the battery will last?
can i use 4 k resistor
Bro can I use it for a single led with same timing
Yes
What to do only for 1 led
Can i make police strob light like this way?
Bhai rgb led koinsi use kare 2 colour/3 colour
How should I make a circuit to operate for a long time in the form of 12 cat sliding lights with a 9 volt battery? What type of LED should it be? 15 days - 20 days to run (10 hours per day)
does it work with 3V?
Yes 😉
Does it work 12v
Many thanks. I have subscribed.
Can you use a pot to control the speed?
Today I am going to publish a video on adjustable flasher
Hi. Simulating with Crocodile clip, the white diode, the transistor and a switch are burned. That could be happening? Regards
The circuit itself can''t flash/blink. blinking is done by clamps. It is like a fake video.
I'm building the same exact circuit, but not getting the same result. Not flashing. I'm not understanding this. Am I doing something wrong?
This happens because,the consumption of current is variable rgb led,so red led change his brightness
Can I pay you a consultation fee on a project??
can this work in single 1.5 volt battery or two 1.5 volts battery
Yes bro
Valeu!
Grato!
Excelente projeto!
Boa noite!
Ao SENHOR pertence a salvação! Jonas 2.9
Sorry your video not working with two still leds
Can use 10K in place of 4.7K
Nice setup, just make sure everyone knows that a BMS is REQUIRED for LiIon batteries, to prevent a risk of fire or explosion when those batteries are either charged or discharged beyond their safety threshold.
A BMS??
Battery management system BMS
You build circuits??
What software is used to edit videos?
Can anyone tell me how can I remove these items from my LED panel to get a simple light panel?
Plz make it on zero PCB board
Good sir i am pakistan hasnian shah
Where is the oscillator to this?
Waooo
Thanks!! 😀😀
@@Creativecreator nice project sir...
@@Creativecreator sir next time plz make video to same time 8 to 10 LED falshing circuit making plz sir...
@@hkhobbypakistan6917 in this circuit you can connect 8 to 10 leds in parallel.
Make sure you are connecting the LEDs with the red LED. It will work.
You can also use 1k resistor for series (not mandatory) branch.
@@Creativecreator thankyo sir... I'am trying..
Bhai 4.7k ki jagah koinsa use kare
i cant get them to flash... no idea what im doing wrong...
Olá! Troque a polaridade da fonte e dos Leds. No diagrama está correto.
Dont need these circuit. Just buy a RGB led then connect it with a normal led. It will blink with RGB led. (3.7v) I try his method..... not so bright (2nd led)....
Simply connect a rgb led parallel to any led to make it blink like this
100 led par ye sircute kaam karega kya
Hello sir - Am I gone color blind or are you soldering a 470 ohm resistor instead of a 4.7 kohms??
No buddy it's 4.7k
Nice ..👍👍
Bạn có thể chỉ cho tôi 100 led với nguồn 3.7v không ?
Please make a blinking LED for Drone with chargeable 5V battery light weight
Check my latest video
Do you need the rgb led
Very beautiful video
Rgb led no need transistor for blinken
Too good!
Excelente!!!!
*_BRAVO, SUPER._*
Thanks
a better flasher circuit can be made by op omp that is adjustable for speed of flashing. If u want to know how just comment
Wanna know!
Nice
Thanks
Mantap...👍👍😄
It is a bistable oscillator
I ain't got time or know how for Dat!!!!
I will connect 10.000 powerbank. Fake Alarm light for car How many hours or days will it last?
Nice project
Thank you so much!!
Muốn làm nguồn 5V
Why the videos never look like the thumnail? Do a single led please no multicolor led.
Wow, using no capacitor
Good
👍👍👍👍
NICE
Thank you so much!!
Please subscribe.
It works but definitely not flashier at all
so, why use all those components?
110V
👍👍👍👍👏👏👏👏
5V
This is not working
Its fake because you just show battery wires why you don't show the battery
Lol you’re creating a flasher using an led that already has flasher function built in. Stop fooling people
Hjj
no .
This fake video because one of the two led light is blinking bulb
Bom.e.fase.e10
Fake hai. Led blinking hota hi nahi
no man bro dont post fakes my man
Iithiun
I wonder why yt removed the dislike button
This is waste circuit does not flash at all
Fake h
Faku video
Fake
Can we use any other led instead of rgb
Yes, but there has to be 2 leds
Nice
Thank You So mUch!!