Just did the maiden with my (standard) Swordfish, only in manual mode for a beginning to test the trims and courses, all ok...but looking at the video recorded in the goggles, no OSD! I looked in the menus and didn't fine anything to configure...did I forget something? Awesome video, you are at an other level with this VTOL!
The tilt arms were purchased from a Chinese online seller since they have all the bearings and screws ready to install so I don’t have to purchase them separately. You can use this www.thingiverse.com/thing:6140476, just mod it to fit the motor mount hole on the Swordfish, and get those bearings and screws
Nice, Looks like it flies great! I have been building a Swordfish VTOL on and off the last couple of months and i'm almost done. Can you share your tune in ardupilot for your model? I have the rear motor on the top of the tail, however i would not think it makes a huge diffrence.
You won't be able to purchase it unless you have Chinese shipping address. But you can use this www.thingiverse.com/thing:6140476, just mod it to fit the motor mount hole on the Swordfish, and get those bearings and screws
The tilt arms were purchased from a Chinese online seller since they have all the bearings and screws ready to install so I don’t have to purchase them separately. You can use this www.thingiverse.com/thing:6140476, just mod it to fit the motor mount hole on the Swordfish, and get those bearings and screws
I need one of these as well, currently have the smaller brother - dolphin.
Just did the maiden with my (standard) Swordfish, only in manual mode for a beginning to test the trims and courses, all ok...but looking at the video recorded in the goggles, no OSD! I looked in the menus and didn't fine anything to configure...did I forget something?
Awesome video, you are at an other level with this VTOL!
Make sure you did the WTFOS mod if you use DJI system. Check this out ardupilot.org/plane/docs/common-msp-osd-overview-4.2.html
@@FlyByWireC thank you, will try to understand what is is said, not a specialist!
But I use INAV, is it the same?
@@alainrac56 You need to use ardupilot for the VTOL, for the best and most reliable performance
Where is the rear motor for vertical take off? Ah ok, I saw it!
😄😄😄 keep low profile
Where can I find stl for the motor pods? Thanks
The tilt arms were purchased from a Chinese online seller since they have all the bearings and screws ready to install so I don’t have to purchase them separately. You can use this www.thingiverse.com/thing:6140476, just mod it to fit the motor mount hole on the Swordfish, and get those bearings and screws
Nice, Looks like it flies great! I have been building a Swordfish VTOL on and off the last couple of months and i'm almost done. Can you share your tune in ardupilot for your model? I have the rear motor on the top of the tail, however i would not think it makes a huge diffrence.
I can share you my param file through email, but just keep in mind using it may cause a crash or other issues. Since our setup may be very different.
@@FlyByWireC Great thank you! I will look over all parameters before first test, but i think it will be a good starting point.
@@FlyByWireC how do i write to you in a private message?
I don‘t know how to do that. Are you able to leave email in the comment and delete it when I have sent you the file@@sondrehetland
@@sondrehetland I think it won't be leaked since my channel only has 5 subscribers and two of them are my friends😆😆😆😆
I need one awsome video
Thank you！😄
Drop the music
Hello, what’s the weight of it ?
Taobao has a lot of Vtol parts options
I don't know what to buy Should I just buy 23 left and right mounts?
item.taobao.com/item.htm?abbucket=10&id=667700063245&ns=1&spm=a21n57.1.0.0.1991523cgCahoQ&sku_properties=31309:18544195000
You can talk to the seller on taobao to make sure they will sent you the correct parts. I brought the left and right mounts
Cool man, can you share link to purchase that tilt motor mechanism
You won't be able to purchase it unless you have Chinese shipping address. But you can use this www.thingiverse.com/thing:6140476, just mod it to fit the motor mount hole on the Swordfish, and get those bearings and screws
how did you get your osd to look like that??
good video, would you be so kind, where can I buy this pnp plane? Just to install receiver and battery? greetings
atomrc.com/products/atomrc-swordfish-fixed-wing?variant=39970705473669
Lots of work to do
but the drone version does not come.
@@FlyByWireC Where can I find a manual to build it?
No manual you have to research everything from scratch@@alejandrofernandezgalea8732
Do you have the configuration and what fc do you use, thank you
F405-VTOL, my configuration may lead you to a crash or result a bricked fc, better to setup your own
is this ardupilot or inav? what is this magical osd sorcery you got going on here!? i have so many questions! lol
Ardupilot of couse. Feel free to ask anything, the OSD is WTFOS mod.
@FlyByWireC ohhh, I have the wtfos already done, but only regular font then. Where can I find the cool kids font?
@@AiroFpv Oh, that's the Video Editor's Element, not OSD😅😅
Did you not read the intro,it's clear as😂😂😂😂😂
Can i ask where you sourced the parts please?
The tilt arms were purchased from a Chinese online seller since they have all the bearings and screws ready to install so I don’t have to purchase them separately. You can use this www.thingiverse.com/thing:6140476, just mod it to fit the motor mount hole on the Swordfish, and get those bearings and screws
1st. one ....☺😋
Thank you Captain Rene! 😄
Thats not a maiden sorry😂😂