Ridgeline Roof Rack Installation (Honda Answers #71)
HTML-код
- Опубликовано: 16 сен 2024
- Honda Answers Question 71: How do I install a roof rack on my Ridgeline? (Part # 08L02-SJC-100A & 08L02-SJC-100B)
For a complete list of tools and instructions go to www.handa-acces...
Product and parts are available at www.handa-acces...
Carmichael Honda's Online Accessory Store
The Largest Honda Accessory Dealer in the United States.
Offering local order pickup in the Sacramento Area and fast shipping to all 50 states
I found the instructions online. I love how Honda says this is not a job for “do it yourselfers.” And they put it in quotes just like that. You need three sections of trim on each side. Two cuts of the following three lengths... 555mm, 425mm and 230mm. That translates to 55.5cm, 42.5cm and 23.0cm :-) You should end up with 33cm of scrap to discard on each side.
Great Video. Great instructions. Would have been nice if he had reported how long to cut the pieces.
Thank you very much for this! Just finished installing mine, took me a lil more than 45 minutes but came out nice!
Useful video for the most part. I've added some "tips" below because... Unfortunately, instead of inserting a voiceover that could have helped with instructions..... they just played annoying music. If no speaking.... then why the hell bother with sounds at all?
That said... I'd like to add some useful tips that they should have brought up.
1. Cutting the roof molding to lengths specified by the instructions is fine advice, IF you have instructions. Which I didn't and which is why I had to watch a video in the first place. So... I had to figure that part out myself. ANSWER: Place roof rack temporarily on roof beside the track and in line with the screw holes. Then... place the track cover next to it with its front end in line with the start of the groove (where it would normally be resting) then, with a marker, mark off the beginning and ending of each of the points of where the roof rack drops into the groove. (the block that the screws pass through) Then cut away those areas.
2. A disk grinder with a metal cutting blade will also work quite nicely.
3. When assembling the roof rack on the bench, you will notice that on one end of the cross members where they slip into the plastic caps, the caps holes are round and on the other end they are oval. Screw the round ones in tight but leave the oval ones a bit loose. You will want a little bit of play while mounting. These can be tightened fully later.
4. When bolting down the rack to the roof, you will notice that the bolt holes in the center mount are round and the ones at each end are oval. This is because the rack lengthens as it's compressed. This can cause grief if not assembled in the right order. First, loosely attach center nuts. Then loosely attach ALL of the rest. Only then do you begin tightening. And fully tighten down the center before moving on to the ends.
5. lastly, for the people without the instructions like me..... when you go to put the cover caps on, you will notice that they have been marked on the underside as to which side of the vehicle that they go on.
GOOD LUCK👌😀
Found the OEM instructions in less than 10 seconds. Google's your friend. There's also a link in the video description above.
www.hondapartsnow.com/installation/AII12033.pdf
@@OMGWTFLOLSMH They removed this it is 2021 now and took it down un-fortunately
Super simple! 🎉
Excellent video... thanks for sharing.
Do you guys know what this mean in step #11 of the installation manual? "To reduce wind noise, cut the rubber molding from each roof rack and install the pieces of the rubber molding you just cut between the crossbars.
I'm considering installing roof rails on my 2017 Ridgeline but I really don't think using a little hand saw is the proper way to cut the plastic rails from the roof...
Is there an easy way to remove the cross members without removing the roof rack?
If you have found it, please let me know......I cannot find any details on how to remove cross members....
Cause major water leaks in my headliner water this install years later
Did you try your local dealer for a part # first ..then you can go on line and purchase it cheaper.
Is there a link of this roof rack with cross bar for the 2021 Honda Ridgeline? Thanks!
How do you know where to make the cuts on the channel trim piece? Also-will the rack hold a canoe. 14.5’?
Is the video instruction #71 the same for the 2017 Honda ridgeline roof rack oem rails and crossbars?
Nice!
Quick question is that gonna fit on honda crv 2000 first gen?
Would this be the same process for an Older Honda Pilot?
What’s the part number for this rack
yes pls can u tell the long
can i install roof rails of honda pilot 2004 on my acura mdx 2004?
Is the cross bars adjustable?
Yes
How bout for 2018 Ridgeline RTL?
Who can you contact to find one of the caps.I am missing the front passenger side cap to the roof rack of my 08 ridgeline.
zac turner blrice
zac turner what is the price
just installed on my 2018 and now I have lots of wind noise. any suggestions?
I have them on my 2007 RTS and always get wind noise. I'm thinking about removing the cross bars but haven't yet found a video showing how.
Thanks for this.... Def bot getting one.
add a Thule air screen to the front of it
I took the crossbars off. I just have it for looks and this helped with wind noise.