इंजन का काम कराने के बाद क्या सावधानी बरतनी चाहिए? | HOW TO BREAK IN YOUR REBUILT MOTORCYCLE ENGINE
HTML-код
- Опубликовано: 9 фев 2025
- If you spent lots of money and hours of hard work rebuilding the engine in your motorcycle, scooty or scooter the last thing you want to do is ruin all that hard work by failing to properly break in the motor. The steps to follow for breaking in a rebuilt engine once it's running again will vary slightly depending on the type of engine. For example, the steps for a high-performance street bike requiring high RPM for peak performance differ from a more sedate side-by-side that relies on lower RPM torque to get the job done.
Adding Conventional Motor Oil
Fill the motor with a conventional engine oil, not a synthetic. Synthetic and semi-synthetic oils are too slippery and slick, which prevents the new piston rings and cylinder bores from seating properly. During the first few minutes of running, the piston rings and the walls of the cylinders need a small amount of friction so they can wear fractionally, and so their surfaces can conform to one another to form an effective seal. It's this seal that gives an engine good compression, and it's that compression that really adds to the performance of your rebuilt engine.
Static Engine Run to Operating Temperature
The first time you restart the motor after a rebuild should be a static run. Wheel the machine outside or make sure you're in a well-ventilated space. Then, start the engine and bring it up to operating temperature while gently varying the throttle between idle and 50% open. Don't go over 50% throttle at this point. Once the engine has warmed up, give it a thorough inspection for any leaks; listen for any odd noises; and look for any other mechanical issues such as excessive vibrations. Shut off the engine and let it fully cool down.
20-Minute Active Engine Run
An engine break-in happens mostly during the first 20 minutes of running after the rebuild. If you have access to a dyno, strap the vehicle down and vary the load on the engine between idle and 70% throttle. Otherwise, take the vehicle for a short ride to put a load on the engine. Vary the throttle between idle and 70% to push it a little harder than you did in the static test. Find somewhere without any traffic where you can safely run the vehicle while varying your speed to break in the engine.
Assuming everything goes well and there are no mechanical issues, start varying the throttle between 50% to 80% to further increase the load on the engine. Next, run the vehicle as you would in normal operating conditions.
#EngineRebuilt #EngineOverhauling #Automobile
Join my channel and become a member : / @mechanicaltechhindi
The wait is finally over. I am here with RUclips's very first Automobile & Mechanical Engineering Channel in HINDI.
In this channel i will upload videos related to automobile and mechanical engineering topics such as engine, I C engine, Cars, Motorcycles, Production, HMT, Thermodynamics, FM, CAD/CAM etc.
So subscribe my channel and learn everyday
Follow me on twitter: ⤵
/ dashingdanish11
Add me on Facebook: ⤵
/ danish.ali.754
Follow channel on Instagram: ⤵ / mechanicaltechhindi
Contact me: ⤵
mechanicaltechhindi@gmail.com
सर आपकी इस विडियो को देखकर ऐसा लगता है कि अब हमारा ज्ञान और नोलेज बढ गया है और आप का धन्यवाद ओर आभार व्यक्त करता हूँ ऐसी महत्वपूर्ण जानकारी देने के लिए.........👍👍👍👍👍👍🙏🙏🙏🙏🙏🙏
❤❤❤❤
Bhut achi jankari di apne bro.thank you.
Sabse badi baat video me time waste nahi hua to the point baat ki 👍
Helpfully video sir ji
Thanks so much sir ji
Jai Hind Jai Bharat
Vande matram
Starts from 5:40
Thanx
Thnx
Bhai ❤
Thanx
❤
Recently I subscribed your chenal Vary informative & nice presentation your each video's Thanks keep it up.
Sukanta , Silchar Assam
😊👍👍👍
Dhubri here
Thanks for the valuable information. Maine engine bore karvaya. I will follow the instructions.
Intni sahi jankar dhanywad
Thank You ! Respect Brother! God bless you!
Bahut dino se wait kr raha tha
Sahi video banate ho Bhai
Bhai app tyre k upar koi video kar do.mera aveger 160 street bs6 main eurogrip ka tyre mila hain, mujhe lagta hain ki mrf ka milna chaiye tha.
Nice knowledge bro thanks👍👍
बहुत सही और बढ़िया
Very very thankful & helpful info about engine work, and then precaution its helpful info about rider
Very informative video sir❤️❤️❤️
Thanks for the information mera v engine naya ban k aaya hai
Namaskar, brother Aapke explain Ka tarika bahut achchha hai. Isi Tarah se aap hame guide karate rahe.
1 min silence for those who run bike 70 + one second day 😂😂
🤣🤣
Yeah... I crossed 80+
Bhai. Mene to 90+ kar diya gadi me se awaj aa rahi he tej 😭😭
@@sarc769 activa 90 jata bhi hai 😂
😆😆😆
Most informative video boss 👌👌👌
Thanks for important information
A bat to shai he sir 👍 super nice sir
Thanks you bhai
Welcome
Thanks for giving these information
Great
Thanks bro from nepal
Welcome
Nisha gurgain ko jante ho kya
Tik tok wali
Sahi baat batate ho
Tq so Mach
Tnk sir
Bhut achhi jankari dete h aap 👍👍👍
Good explanation
Bhot bhot धन्यवद् 🙏
Dost jai mata di bahot badhia vdo
Tq so much bhaiya ji
Aap bataa saktey h ki old model passion plus ka top speed kitnaa tak hoga 90 ya 100 km/h.
Bhai... Very useful information... Thanks so much bhai.. Keep it up
You are best
Thanks 👍
Very nice video
Nice information bhai 👍
thanks brother abhi kuch din bad engine ka kam hoga activa ka to achchi jankari di aapne thanks
Mera glamour (2012) kaa block kit change huwa 70000 km pe, mechanic ne change kar ke uspe valvoline 20W40 900 ml mileage Plus Mobil dala, uske baad unhone 20 din ke baad engine oil change karne ke liye bola, meyne 1 month ke baad change Kiya, 200 km chalane ke baad, aur Mobil dala Apollo 20w40
Kitana kharcha aaya block kit change karne par
@@dalendrasahu9345 total 5000
You are right
Thank Bhi ji
nice information ❤️
Very good
Bhai mera half engine bana h pulsar 135 ls ka abbi 500 km me kitni ki speed me chalaau bike apni
Sir mene meri tvs phoenix 125 ka engine repair kraya tvs k service center se uske total all engine parts change hue jo ki 7000 k parts hue or 3000 unne labour charge liye kam hone k baad mene bike unke kehne pr 30 40 km ki speed chlaayi phir first service krayi or service k baad mene gaadi nrml chalayi 70 80 km tk lekin first service k baad bike k engine head pr rubber ki seal h uske aas pss se oil leak kr rha h toh m apse yehi puch rha hu ki mujhe service center m jkr ky krna chhhiye
Nice channel
😮ab mere ko bhi problem hone wala hai maine bike ka full engine kraya hai to finally ab log mere ko max😂😂 20 to 50 speed😂😅par dekhenge...o bhai first time...i got thiss 🎉achievement😂 Like karo guy's
Load ke bare me nhi bataye hain sirji .
Please make a Video on Honda Unicorn 150 cc
sir agar full engine ka kam krwa le aur sab chiz ache se fir se dhyan de time se service karaye to engine ki life pehle jaise ho skti hai ?
yes
Sir ji scootor ka half engine bananeki baad double load chalasakty hy ya nahi?
Nhi
Bhaiya ji dubble sawari kar sakte hai
Good video
Hello sir meri passion pro he aur vo oil khati he to me engine banana padega bolck piston naya lau ya boring karau bataiye
7500 खर्च aayega
Bhai gadi ka piston pr timing chain change karane k bad gadi ka milege kam ho jata hai kya
Nhi
Apki machenic ne sahi se fit nahi kya he Syed engine ko...
Thanks
Nice infor
Sir
Mere machanic bol raha h
500km tak one singal person hi bike chlaye two person bhi nhi bike per
Pls sugest me
Cbz xtrem main piston dalwaya h
Yes he is right. Kamse kam load par bike chalaiyega still 500-700km atleast.
Mene jis mechanic se piston change krwaya h usne bola ki 40 speed se km chalao
For your engine lyf bro 50 minimum nhi toh piston bol jyega
Sahi bola hai usne.
Bilkul sahi bola hai. Maine bhi engine banwaya hai usne yehi kaha ki 35to40 se zada na chalana
Sir mare pas cd100 (old model) bike hai
Sunday engin repair kiya tha
100num ka piston lagvaya tha (phle 75num ka tha) or other parts new fit kiye the, Night ko jb mai ghr ja rha tha to mane speed 40 pr rkhi thi or arround 5km door jane ke badd bike bnd ho gye tab kafi try kiya but bike start nhi hui, tb to ghr chla gya, or next morning jb bike start ki to first kick pr start ho gyi,
( Mujhe ye pushna hai k bike bnd kyu hui, speed bhi limit thi or distance bhi jyada nhi tha, mechanic ne bhi sb work shi se kiya tha)
plz tell 🙏
Can we ride Two person after engine work
Only after 500 kms
Only after 500 kms
Engine repair k bad idle screw ki setting kaise karni hai ye batao please. Kyu k mere machanic ne idle screw ko touch bhi nahi kiya. Wo usi position mein hai jaise engine repair k pahle tha..
SIR,Thanks for information.GHAZIABAD
Engine banbanke bad long tour me ja shakte hain ki nehi
Maine engine ko boring karbayata abhi engine bahut garam ho raha hain kya ye problem hain ya pir bore kar ne ke baat naye main hota hain?
Tysm
Sir double pillion kab beth sakte ha.? Plz bataye
Tq bhai Saab
Thnx sir 🙏🏻
Welcome
@@MECHANICALTECHHINDI sir Activa engine ka kaam krwane p ,kitne life rh jatee h engine ki??
Enjoin recording or servicing ke kya aunter hota hai ? Kya galti kare se enjoin reapair ki nobat aati hai ?
Motul Maine dalwaya sir shine main 10w30w kuch nushan hain kiya phir Hum kun sha oil dalwaye shine bike main
If I want to put a new priston and ring which should i must put for mat mojar four strock two wheeler
VERY INFORMATIVE
Sir double loading chala sakte hai
Oil kab change kare.. engine banane ke baad.
Bhai bike ka engine banne ke baad single sitting chalye yaa double chla sakte hai
Mene half engine ka kaam karaya hai, scooty accelerate karne par vibrate kar rahi hai. Ghar ghar ka sound aa raha hai.
Please suggest.
Or double sawari ride kar sakte h ya nahi?
We want part 2 of this video
Bhai ji
Full engine karne ke baad bike pe rider ke alawa 2 lok betha sakta hai kya? Or daily ek baar start pe kitna k/m
Chalaye?
Please🙏 reply
From__West Bengal❤
Thankyou so much
Bhai head block ke net mein se oil aata hai to koi dikkat hai ki nahin aap jarur bataiyega
बोरिंग सही है या नयी ब्लॉक सिलंडर डलाये
Thank you sir
Can you take double load in pillion seat after half engine rebuild
for all those wondering this question you can after 500 km you should maintain your speed below 50 so that your pump is tightened without excess stress, strain in engine and a servicing is needed to be made after 500km as they have to tighten some engine components after rebuild do change engine oil too. After its made nice your bike sounds like new and runs comfortably without any problem. Also its advised to change your chain socket around 15000 km interval and change your clutch plate around same time after half engine has been made i.e. depending on its wear out around km as 15000, 30000, 45000, 60000 and so on. I hade made my half engine around 40000 km and its good condition now running smoothly Bajaj Pulsar 150cc ...
bhai half engine ya full engine ke baad break-in karne ke baad kya phir se long rides pe jaya jaa sakta hai??? long rides matlab ladakh hogaya ya kahi aur...
@@dishantpanda haan bhai par 1-2 servicing k baad will be better option kynki tab tak aapko basic understanding hojayega apke bike condition ki but do test the pickup of it in uphill ladakh k liye aur difficult route k liye..
@@BruceWayne-lm2or bhai nayi bike ka pickup kam reheta hai kya???
@@dishantpanda yes until first servicing afterwards its ok else if you experience problem please check clutch plate..
Sir can we carry two person after half engine work is done???
Kya 100cc ki bik me 110cc ki kit fiting ho sakti hi bhai
Sir kitna mileage degi full engine karane ke baad mera trip meter kharab h
Thank you boss 👍
U r most welcome
Thankyou bhaiya ❤️
Conventional Mobil koi company suggest karein sir
Bike ka kaam hone ke baad kitne ke Speed se chalaye
40
40
Bhai ek person ko peeche baitha sakte hai? Engine ki service k baad?
Sir engine flex karna sahi hai ya galt ke
nice
Double sawari baitha k Chala skte hain ki nhi .
Sir can you please tell me my 160cc apache 160 4v bike, can I use semi synthetic oil?
rgt h sir ji🙏🙏