@@Charlotte63567 You may need at least 12v 3A power supply. I bought this board and now using it with 12v 3A power supply. The board is amazing as I am using it to drive my 6.5 inch JBL GTO609C two 90Watts speakers. Although the board is unable to handle more than 60 percent of the volume from my samsung tab s4 the sound quality is incredible. Need to use a volume potentiometer and a decent power supply with it. I have seen others have used 18v 3.5 A laptop's power adapter with this board.
They have a mistake there, one of the speakers is connected in anti-phase. The output does not have a common ground, it cannot be connected to headphones.
Hii bro.... love your videos so much.....can you please tell me what module did you use after soldering the potentiometer..? Please bro I have all the items except that thing. Please tell me
That's RCA Audio Input female jack usually placed at the back of the amplifiers but its not necessary. You can skip that part and directly connect it to the Bluetooth module Audio Input.
use a tone control preamp, the one that has bass, mid , treble, volume controls.. these TPA amps are known to have less bass and high on treble, so a good preamp is required.
@@Science.H respeitando a impedância que o amplificador pede você pode ligar qualquer altofalante, creio que este suporte 4 ohms, mas eu não tenho certez
Has noone else but me tested this card with speakers capable of deep bass? Because there is a fault on the board. Connected as in this video the right channel polarity is wrong. I first connected the speakers in the order indicated: R-___R+___L-___L+. Then I played "Bass all day" (Bass Mekanik) and almost all the deep bass was gone. Very dissapointing. But then I (by misstake) reversed the right speaker, so the connections became R+___R-___L-___L+ - That is, both minus in the middle and both plus on the outside connections and even the lowest tone was strong enough. I have tested over and over again, and with different speakers, and the result is the same: The printing on the board is wrong. The right channel polarity should be reversed, R+ should be R- and R- should be R+. When connected correctly it is a rather good amplifier. Not quite up to a real discrete class AB amplifier like the Valutronic Poweramp 5, but enough for shorter listening periods.
Hey people, I have this and I have a humming/buzzzing sound as soon as I connect my phone. The sound and music is very good but the buzzing never stops o.O
@@ЮрийЗахаревский-ц9д а у меня выгорают и не могу понять от чего ! Я на выходе подключил реле с задержкой и все начало выгорать. Если интересно могу скинуть схему подключения
This is not a 30 +30 w amplifier because tpa3110 ic is a 15+15 W ic for 30+30 it needs 2 ic but this amplifier circuit board has only 1 ic
The power is very strong and the sound is clear and cool
Can i use 19 volt laptop charging adaptor
Suplai 12,6v = 3x3,7v + BMS,SPK 4inc x 2 + 1 tweeter mantap banget
AMIGO TUDO BEM ,ENTÃO EU LIGAR ESSE PROJETO NUMA FONTE SIMÉTRICA DE 12W?
Gracias, está bien explicado, quiero aprender
Terimakasih kasih video nya.. Saya jelas... Tapi hasil tes punya saya terbakar amplifier nya, sebelum lihat video anda.. Tank's
I have this for my conten... Music library youtube... 👍👍👍👌
If i connect it on 12v supply, is it gonna have same output power as it is connected on 24v?
3:02 Power supły 24VDC, 7805IC +12VDC why ?
AMIGO EU TENHO DOIS AUTO-FALANTES DE 30 + 30W EU POSSO LIGA ELES EM CADA CANAL?
30+30 watt amplifier can out put 60 waitt in one channel
No
it's 30w each channel. using single channel is still 30w
agar amplifier me aux wala connection kre to awaj or bass same aati ha ya kam pls reply
Hi, I really liked your idea, can I use a 50k potentiometer? thanks!
PSU from notebook with 19v 1.5A is enough for setup with x2 speakers 8ohm 15w?
I doubt it.
Could be. You would need to think in terms of WATTs. 19vx1.5A = 28.5 Watt.
what is the maximum voltage that can be supplied from the tpa3110 2x30w?? and what is the maximum amperage?
Max Voltage: 24V
Max Current: 3A plus
Can i use 12v 2A power supply on tpa3110?
@@Charlotte63567 You may need at least 12v 3A power supply. I bought this board and now using it with 12v 3A power supply. The board is amazing as I am using it to drive my 6.5 inch JBL GTO609C two 90Watts speakers. Although the board is unable to handle more than 60 percent of the volume from my samsung tab s4 the sound quality is incredible. Need to use a volume potentiometer and a decent power supply with it. I have seen others have used 18v 3.5 A laptop's power adapter with this board.
@andrewsemodio191 Use Aux to RCA Cable , Put 3.5mm in your phone and the other end in the female RCA jack.
Room tour video podunga bro
Sir please tell me how much ampere do you used?
im using BT earbud units for signal, how do i get the neutral/neg wire when the transmitter only has 2 output wires
Kya 12v 5amp ke adaptor ka use kr sakta hai
Can 20w speakers can be used on 1side and 30w on other?
Should be fine, just try
No
Speaker kharab ho jayega
Yes , Its will work ok
I have 2 pcs speakers, 30W 4ohm each, can I use this board to have sound? Thank you
Yes
Que potenciómetro utilizaste por favor gracias
47k - 50k ohm
How about a parts list please? I have amp and bluetooth module already. What display are you using? What is wiring diagram? Thanks.
The display name that he used is mp3 module 5v
Good day friends.. The problem of me d.i.y. how to wire potentiometer like that.. How wire to have volume like that where to wire 6pin any link..?
Can I use this for the Sony SS-CBX77 x2 ?
(30watt 6ohm )
Yes
Is that realy needed the volume controller i dont have that one and tried mine its not working. Is that tha cause?
OLÁ AMIGO, VC PODERIA ME INDICAR AS POTÊNCIAS DO AUTO-FALANTE MAIOR E DO AUTO-FALANTE MENOR POR FAVOR?
Is 25W 8ohm speaker run in this module?
They have a mistake there, one of the speakers is connected in anti-phase. The output does not have a common ground, it cannot be connected to headphones.
Hii bro.... love your videos so much.....can you please tell me what module did you use after soldering the potentiometer..? Please bro I have all the items except that thing. Please tell me
That's RCA Audio Input female jack usually placed at the back of the amplifiers but its not necessary. You can skip that part and directly connect it to the Bluetooth module Audio Input.
Dc conversor.. 12v to 5v
Full sound veka mudiyuthu?
Why 2 diff loud speaker ? Should this be stereo ... R and L channel ?
that's great!
How if i use one speaker 100w than the out ampli R -Ground and L -ground i Put to one speaker. Is it can running ?
I am not getting much bass in my tpa3110 amplifier.
What is the solution to this problem?
use a tone control preamp, the one that has bass, mid , treble, volume controls.. these TPA amps are known to have less bass and high on treble, so a good preamp is required.
18v 3.5A work or not
Work
Clear amplifier.
I used same the board, also connection input output speaker & power supply
No sound output at 2 speakers but indicator led already ON
Pls help....
Sw don't short
vai potentiometer ka bin amlifire chaĺiga kia
can i connect 4 inch speaker to it?
Tap 3110 me 3wat 4oms kitne so laga sakte
Can I use 3w x 2 speaker (parallel) at the one end and the other one 30w speaker
Use can use a but keep that speakers in 3w speakers in series there you see a good output
Yes but you'll need to do a passive high pass filter, or you speaker will die
Saan po nabibili Yong IC?
Estas placas só servem para alto falante pequenos max 8 p. porque não da o grave forte.
Oi, eu tenho caixinhas de 4ohms, são de um home theater, poderia me dizer se posso usá-las?
@@Science.H respeitando a impedância que o amplificador pede você pode ligar qualquer altofalante, creio que este suporte 4 ohms, mas eu não tenho certez
Minimum input power?
TPA3110D2 Is rated 30W into Mono only.
Why connect faceboard that 50w to an 30 watt amplifier board. The face self can give more the amplifier
Nice ampli
Ic regulator seri?
Has noone else but me tested this card with speakers capable of deep bass? Because there is a fault on the board. Connected as in this video the right channel polarity is wrong. I first connected the speakers in the order indicated: R-___R+___L-___L+. Then I played "Bass all day" (Bass Mekanik) and almost all the deep bass was gone. Very dissapointing. But then I (by misstake) reversed the right speaker, so the connections became
R+___R-___L-___L+ - That is, both minus in the middle and both plus on the outside connections and even the lowest tone was strong enough. I have tested over and over again, and with different speakers, and the result is the same: The printing on the board is wrong. The right channel polarity should be reversed, R+ should be R- and R- should be R+. When connected correctly it is a rather good amplifier. Not quite up to a real discrete class AB amplifier like the Valutronic Poweramp 5, but enough for shorter listening periods.
can i use a usb micro charger cable as a power supply on this?
no
No - Input Voltage is 8v to 26v (DC) Maximum
How's the sound quality?
Good
A machine golo ki Flipkart kinte paava chai
Ano kaya sira sa board ko sir..nag on siya pero walang tunog .left right..nung una tumunog kalaunan hindi na..ano kaya sira sir
Ganun din nangyari sa board ko. Ang naririnig ko nalang e parang tick tock ng orasan.
Porque estrala muito
It's got bluetooth.. why u add rca component inputs bro
Just for people who dont want to put Bluetooth Module.
for me it stops after 4 sec and works when I restart it, how to fix it?
Tpa 3110 amplifier audio garm kyon hota hai is video banaye
How to add bass and treble in the same amplifier kit
XH-A901
Tpa3110da hoda tpa3118da hoda
hello everyone!! please can someone tell me how to fix the buzz noice? i have the same exact TPA3110 XH-A232 and bluetooth board... thank you
You can usa a B1212S-1w on The Bluetooth board. Making this, The buzz noice going to far away
this amplifier retailer specs is fake it's actually 15w per channel the only total power 30w
Am getting sound clipping when volume is raised, what to do?
Which ic do you have used for the amplifier
Use 12v 3amps power suply
Nice one
Sayun ra kaayo
Can we use 12v 1A power adapter for input
yes but power will be limited, better 3a or more
No just use a 12v 3a so u will not see any sound drops and shutting
What value potentiometer
To adjust the stupid volume.
Reply to Creator: Why did you put potentiometer?
Hey people, I have this and I have a humming/buzzzing sound as soon as I connect my phone. The sound and music is very good but the buzzing never stops o.O
nope 30+30w max 12.5wrms 😜😜😜
Headphone output and led vu meter?
Tidak nyaman dlm mengamati / mempelajiri ... 😭
Punya saya beli baru, mati sebelah
Видео не о чём!!?
puyak saya gak kluar suara tp IC panas ,
Вопрос: если динамики не подключить усилитель сгорит?
Нет, ничего не сгорит
@@ЮрийЗахаревский-ц9д а у меня выгорают и не могу понять от чего ! Я на выходе подключил реле с задержкой и все начало выгорать. Если интересно могу скинуть схему подключения
Это из-за ника, очевидно. Всё так и будет выгорать.
Kirim WA
gg
Show de bola meu amigo
നിങ്ങൾ യൂടൂബിൽ ഇടുന്ന വീഡിയോ കളുടെ സാധനങ്ങൾ ഒന്നും നിലവിൽ ലഭ്യമല്ല പിന്നെ എന്തിനാണ് ഓരോ വീഡിയോയും ചെയ്യുന്നത്
Bekar board hai 5+5 watt ka bhi sound nhi hai
Идиотизм! Динамики без акустического оформления!
Land jaise testing
Second view
Why can't people TALK instead of wiggling an item in a video?? TALK DAMMIT!!!
Terimakasih kasih video nya.. Saya jelas... Tapi hasil tes punya saya terbakar amplifier nya, sebelum lihat video anda.. Tank's