Checking Oil Pump of Electric Chainsaw Makita MUC351 / Fixing oil Pump

Checking Oil Pump of Electric Chainsaw Makita MUC351 / Fixing oil Pump
......................
Thanks for Watching My Videos
Please Like, Share, and Subscribe this Channel !!!
www.youtube.com/@maxtoolrescu...
......................
Please Watch More Videos :
-STIHL MS382 Chainsaw / Repair and Close Oil Tank Hole / Fixing Chainsaw MS382
• STIHL MS382 Chainsaw /...
-How to Change Earth Auger Machine Cylinder / Mitsubishi (copy) TL 52 Earth Auger
• How to Change Earth Au...
-Repair Mini Chainsaw Made In China Newest 588i / Repair Chainsaw
• Repair Mini Chainsaw M...
-Repair Chainsaw STIHL 031 AV / Fix Chainsaw
• Repair Chainsaw STIHL ...
-Repairing Chainsaw STIHL O8 / Fixing Starter / Replace Kit / STIHL Chainsaw 1963
• Repairing Chainsaw STI...
-Replacing Chainsaw Crankcase STIHL 070 / Old Crankcase Need Replaced by New One (Copy
• Replacing Chainsaw Cra...
-Fixing Chainsaw STIHL 070 (copy) / Replace Cylinder and Piston / Cleaning Carburetor
• Fixing Chainsaw STIHL ...
......................
#MaxToolRescue #ThankYou #SubscribeNow

[@mattmcintyre7083]

Coffee drags itself out of bed and has a cup of this dude every morning.

[@patadegrillo007]

Lot of patience especially listening to that piano!

[@muhammedharrak]

Teşekkür ederim kardeşim. Sorunu başarıyla çözdün. Teşekkürler

[@garengtutorial8923]

Keren bro mantappp

[@user-it1wl4lg2c]

👌👌👌👌👌👌👌

[@richardkistner5549]

Thank you!

[@wojtekjarosz4072]

Thank you. Now I know what it expect when I get in there, and I will have to. Perhaps flushing the pump with some not very flamable solvent would be a reasonable first attempt, as I am reluctant to take apart all the little tubes... Anyway, big thanks!

[@oskosknextime6883]

W tamtych rejonach wszyscy pomagają sobie stopą xD

[@bohmdan81]

safety first 🤗

[@maxtoolrescue]

Yes, thanks

[@phillipendersby6964]

I would check the oil filter in the tank first

[@joseantonioballesta5426]

Muchas gracias me has dado la solución exacta q buscaba

[@glotzfisch]

Please keep your fingers and your life.
Do not holx on to the bearing of a 1000s motor with two fingers when spinning it.
Do unplug the machine when repairing. Touching open contacts can kill you. Or start fires.
Also are you greasing the break?

[@BallBusta]

At 5:06, don't do this. You should never blow a clog back into the oil reservoir for obvious reasons I would think, but I'll explain because this guy clearly doesn't understand. If you blow the clog back into the reservoir you're going to create the same issue further down the line as you're not removing the clog.

[@pooransingh5710]

Which oil and how much is needed per hour???

[@mattmcintyre7083]

You need a special type of oil called Bar Oil. It's made specifically for use in chainsaws. What sets it apart from other oils is that is much stickier. Any other oil won't cling to the rapidly spinning chain, instead getting flung off moments after it hits the chain.

[@superwag634]

youre just making this up as you go...AC voltage, solvent, oil, wet cardboard... Dont do this kids