Nice ! They are really cool. In my video I did make a mistake. When you put the new pin in the washer goes on the opposite side of the charging handle.. I put it on the wrong side so it made the dust cover harder to open.
The pin holding the cover pops out you don’t have to drill it. You just need a proper punch and to hammer it out. Also i believ you put the screw in wrong the washer goes on the other side under the bolt. The squared off side sits in the actual groove.
Yeah thanks! I had fixed the washer after the video when I realized hats it didn’t fit right in the squared side.. I will say I could not get this to punch out at all though.. couldn’t pop off the ring or punch it in.. even after I took off the ring it was still hard to punch through.. thanks!
Reading the other comments the decision to drill through the hinge pin seems contentious. Glad you went through it and it worked out for you. I've been meaning to install my TWS gen 3 rail on my M92. What size drill bit did you use ? If you wanted to return to the old dust cover can you use the TWS pin ?
Yes you can use the TWS pin if you wanted to go back.. but there was one issue with doing that which I can’t remember right now.. I have been away from home for a few months, but when I get home I will post what you need to go back to the old dust cover.. as far as drill size I don’t remember either and not able to look at my guns at the moment . Sorry!
@@Mr_P_Rockzz Thanks for the response. So I tried taking my power drill and drilling into the hinge pin but it barely penetrated. I don't have that much experience with metal work. I read somewhere you want to drill on a lower rpm and use oil.
@@finaljustice3848 really whatever works for you .. I don’t have lots of experience but I have some common sense.. i Remember I started it slower and then when the whole started to open up I was able to speed up the drill so it wouldn’t slip off the spot.. my video is edited so it took longer than what you see.. just drill slow take your time make it look nice so you don’t scratch up your rifle/ pistol. I may have used a small drop of oil but not much . Some people say you can hammer it out but I had no luck doing that.
So the original rail is ok if you want to add a small red dot … if you add a red dot on the original rail you would have your red dot really far forward on the pistol and it has to be a small one.. I couldn’t fit an eotech on the original because the dust cover would not open if I had it on… This new rail is just like any regular rail you can have the optic closer to your face and still have room for a magnifier or anything you want to add
it depends on the eye relief of your optic. i have a primary arms prism 3x and i can barely see through it with the factory rail so far forward on the zpap92. this rail allows you to mount the optic further back for better eye relief.
An update? Nothing really I can think of to make a video on this.. I have used it many times and opened not up and cleaned it and holds zero .. really good rail system
Idk yet I haven’t shot it with this on yet. Also just put a new sight on it so won’t know till I zero, but I have heard this rail is the real deal and good quality
Just a bit of constructive criticism, buy a nice punch set, don't use a drill bit as a punch. Drill bits are brittle and can shatter into small pieces possibly entering your eyes or those of small ones in the same room. Be safe dude.
I tried using a punch like the instructions said. I was hitting the pin for a while using a gunsmith hammer and punch... NOTHING! Didn't move an MM. Then I tried drilling carefully and it came right off
Thanks bro. I literally followed your steps right now and got it done.
Thanks for watching my video!! Glad it helped!!
Great video. My daughter heard babyshark in the background and wanted to watch as well lol
Haha !
Great detailed - you made it seem easy. Love the Baby Shark background music brother 😂 - kids 🙏❤️ 5:20 finished looked awesome.
Thanks for the comment!!:) ! 😃
Just ordered one for my zpap92 yesterday. Thanks for the tutorial and heads up with the pin removal.
Nice ! They are really cool. In my video I did make a mistake. When you put the new pin in the washer goes on the opposite side of the charging handle.. I put it on the wrong side so it made the dust cover harder to open.
@@Mr_P_Rockzz does the kit includes everything u need for the installation or u need to buy that pin and the spring tab
@@mrguiltyfool no it has everything
@@Mr_P_Rockzz thx.
Jack WBP TWS extra team.😊
smoke detector needs a new battery
Thanks! Changed it out long time ago
The pin holding the cover pops out you don’t have to drill it. You just need a proper punch and to hammer it out. Also i believ you put the screw in wrong the washer goes on the other side under the bolt. The squared off side sits in the actual groove.
Yeah thanks! I had fixed the washer after the video when I realized hats it didn’t fit right in the squared side.. I will say I could not get this to punch out at all though.. couldn’t pop off the ring or punch it in.. even after I took off the ring it was still hard to punch through.. thanks!
@@Mr_P_Rockzz nice and maybe yours was different. I was glad mine popped out i really didn’t feel like drilling.
@@soulsweet17 lucky! Believe me I tried popping it !
Reading the other comments the decision to drill through the hinge pin seems contentious. Glad you went through it and it worked out for you. I've been meaning to install my TWS gen 3 rail on my M92. What size drill bit did you use ? If you wanted to return to the old dust cover can you use the TWS pin ?
Yes you can use the TWS pin if you wanted to go back.. but there was one issue with doing that which I can’t remember right now.. I have been away from home for a few months, but when I get home I will post what you need to go back to the old dust cover.. as far as drill size I don’t remember either and not able to look at my guns at the moment . Sorry!
@@Mr_P_Rockzz Thanks for the response. So I tried taking my power drill and drilling into the hinge pin but it barely penetrated. I don't have that much experience with metal work. I read somewhere you want to drill on a lower rpm and use oil.
@@finaljustice3848 really whatever works for you .. I don’t have lots of experience but I have some common sense.. i Remember I started it slower and then when the whole started to open up I was able to speed up the drill so it wouldn’t slip off the spot.. my video is edited so it took longer than what you see.. just drill slow take your time make it look nice so you don’t scratch up your rifle/ pistol. I may have used a small drop of oil but not much . Some people say you can hammer it out but I had no luck doing that.
Great video going for the same set up with my Draco, pls lmk how it feels on the range.
It runs amazing and holds zeros
@@Mr_P_Rockzz based on what ive seen I don’t doubt it one bit,,, where’d you order from?
@@bobbyforbes2409 If I remember right it was right on the Texas weapon system website … but lots of places have it for sale also
How is it holding zero. ?
Perfectly
Since it looks like the stock cover had Pic Rail slots what is the advantage of this new cover? I assume it does something the stock one does not?
So the original rail is ok if you want to add a small red dot … if you add a red dot on the original rail you would have your red dot really far forward on the pistol and it has to be a small one.. I couldn’t fit an eotech on the original because the dust cover would not open if I had it on… This new rail is just like any regular rail you can have the optic closer to your face and still have room for a magnifier or anything you want to add
it depends on the eye relief of your optic. i have a primary arms prism 3x and i can barely see through it with the factory rail so far forward on the zpap92. this rail allows you to mount the optic further back for better eye relief.
Do you mind doing an update on this?
An update? Nothing really I can think of to make a video on this.. I have used it many times and opened not up and cleaned it and holds zero .. really good rail system
Great video! Solid move to just own the baby shark sounds lol 👍
Thanks for the comment!
Did you ever change your smoke detector battery?
Yup yup
About to order one. Has yours held up alright so far?
Yes it has . Went out shooting about 5 different time … cleaned my Ak up completely each time and still holds zero.
@@Mr_P_Rockzz great to hear! Thanks
Will this fit on my PAC Hell pup ?
@@anthony-ze6fc idk about this one but you can order for whatever model you have
Im interested in this setup for my zpap92. How well does it hold zero?
Idk yet I haven’t shot it with this on yet. Also just put a new sight on it so won’t know till I zero, but I have heard this rail is the real deal and good quality
If it means anything, I have the set up with an MRO HD w magnifier and haven’t had any issues
@@45-aarp oh cool thanks!! I heard really good reviews on it, but it is good to hear.
@@Mr_P_Rockzz it’s my second rail, first was for my WASR, getting a third one soon for my ‘74 so I can definitely recommend it
@@45-aarp I was lucky .. I was about to order one, but happened to find it in a shop by me.. id order one for any Ak I get now
The song of the hallway bird.
@@constitutionalist6817 🎶
Just a bit of constructive criticism, buy a nice punch set, don't use a drill bit as a punch. Drill bits are brittle and can shatter into small pieces possibly entering your eyes or those of small ones in the same room. Be safe dude.
Hey thanks! I actually have a punch set now since I needed once for another rifle I was working on.. ! Thanks!
I tried using a punch like the instructions said. I was hitting the pin for a while using a gunsmith hammer and punch... NOTHING! Didn't move an MM. Then I tried drilling carefully and it came right off
@@manny85382 exactly! I tried to punch this thing out and didn’t work so just drilled it out ..
I cringed when he used the drill bit as a punch. I could deal with baby shark but THAT just got me😂
@connorlefler6238 hey if it works it works :p
No worries on the noice and kids brother I know what that's like hahah I have to wait till my kids fall asleep before I shoot content hahah
Haha! Yeah it’s either do it while the kids are there and they don’t judge, or when the wife gets home and she watches me like I’m weird 💀
Send me the old cover 😊
You can have if you pick it up from Texas
hey there, do you remember what size drill bit you used?
I don't ! Sorry
You should have brought it to me, I would have put it together well without all the fuss you made.
@@LeonSlenOfficial 💀
Loveeee 😍
Carelessly handling that swap. Scratching the rifle and all 🤦🏽♂️
It's an AK and guns are tools man.
@@Bearjew2995and damaging your tools from acting carelessly is dumb. Just because something is a tool doesn’t mean you abuse it.