RhinoAG TS10 Flex Wing Rotary Cutter (10' Cut) Only needs 25 PTO HP
HTML-код
- Опубликовано: 26 ноя 2024
- The World's First 10' Flex Wing Cutter that can cut with as little as 25 PTO Horsepower...the RhinoAG TS10 Flex Wing Rotary Cutter. Made in Gibson City, Illinois. Check out the features before this one heads to it's new home. It sure didn't last long on our lot but long enough for us to get a video produced. Visit us at www.vahrenberg.com or RhinoAG at www.rhinoag.com
I’d rather have three hydraulic remotes and have the wings set in the float position. That way the stroke of the cylinders is what actually limits the flex of the wings, and not the notch/slot that it’s connected to. I’m seriously considering the TS12.
You can plumb it for 1, 2 or 3 sets on either TS10 or TS12. Just depends on how many sets of remote valves you have on the tractor. Most small tractors only have 1 set so RhinoAG standard equipment is for 1 set but a dealer can set up how ever you need it, RhinoAG has the conversion kits to do it.
I love a product made in USA!!
We love that RhinoAG Cutters are American Made too! It's amazing how many cutters are not made in the USA but are recognized brands. Need to Look at the Serial Number Plates to Country of Origin. Proud to support our fellow American that Build American Made Products. RhinoAG uses all North American Sourced Steel too. 80% if USA Steel. How many brands can say that too?
I am interested, but would like to see that setup in 1-2ft of overgrown field.
This Video from Big Tractor Power shows some in-field action with the TS10: ruclips.net/video/-DgSQdsSUKE/видео.html
And here is the RhinoAG Flex Wing Video that shows the TS10, TS12 & 4155 Flex Wings inaction and in the field: ruclips.net/video/kOlqi8Efg1E/видео.html
Would like one with a single wing where the wing operates at 90 degrees.
Maybe add in a sickle bar or ditch bank flail on the side with the single wing…
If the driveshaft geometry doesn’t line up then you just make the flail and wing deck hydraulic and leave the center on direct with a shaft.
Also like that one guy said I’d rather have full hydraulic control over the flex rather than letting gravity/the notch control it
Pretty much all wings on Flex Wing Cutters are single acting cylinders... Gravity Fall and Hydraulic Raise. Now the center section is double acting cylinders Hydraulic raise lower.
If you only want a single wing you need to look at the 15' Cutters with only right side wing which are 10' cut. RhinoAG 3100, 4105 or 5100 are the models for those. We've only sold one to a local road district.
@@VahrenbergImplement I’ve seen them I just can’t find it on RUclips.
My point was more like: the single wing is almost perfect for me just needs a bit of modification.
I’d want dual double acting cylinders on the wing so that stability is ensured when using it to trim a hedge.
I wanna throw that wing up at 90 degrees and trim hedges while clearing the ground next to it at the same time.
I also want the extra rigidity to add a second chopper on the wing side to top the hedge or just trim further up it.
Also for doing ditch passes on stuff with light inclines
You need a Boom Mower for that application. RhinoAG makes them too. www.rhinoag.com/products/boom-mowers/hydraulic-boom-rotary/
Would that work on a 2605 2wd with one set of remote in the rear? Also do need more than one control to do it all or two controls
Yes it would work behind Massey Ferguson 2605 (38 Engine/ 32 Live PTO HP or 30 Independent PTO HP) and the 2605H is 55 Engine/ 46 PTO HP. Only needs 1 rear remote is way the TS10 is rigged from the factory.
Could the wings be replumbed to a separate hydraulic circuit? (If customer requested)
Yes. This standard equipment set-up is for a single remote but they offer plumbing options for running with 2 or3 remotes. It's the purchasers choice. Most compact tractors only have a single remote so as pictured in this video they don't have to purchase added remotes for their tractor. It can be done like this, Raise on one circuit and wings on a separate circuit or each wing separate too. Your choice.
See some action of the TS10 by "Tractor Time with Tim" as they cut fields. Here is link to heavy grass & brush cutting video: ruclips.net/video/NAFXhyduaKo/видео.html
I'm trying to buy one in Australia. I'm just waiting for an eta.
They are one of the hardest products for us to get here in the states. Demand is outpacing Manufacturing. Pretty much any cutter made is presold here in the states right now.
@@VahrenbergImplement I guess I'll have to be patient then. Mowing is something I've specialised in for year's and good equipment is the key to reliability and productivity.
If you wouldn't mind sharing.
In your experience, what pto horsepower would you recommend for best productivity out of the TS10? Bigger is not always better.
Jono
We have several on 25 to 30 PTO HP Tractors and the owners love them. Most are from 25 to 60 PTO HP we have running in the fields here.
@@VahrenbergImplement thanks for your reply. I'm negotiating on a low hrs Case farmall 60B atm it will have plenty then.
Please let me know if one of the wings can cut on a 45 degree upward road slope from the level roadbed that the tractor is operating on. Thank you
Here is link to RhinoAG Website for the TS10 at the Bottom is Specs. 90° Up to -22° Down. www.rhinoag.com/products/rotary-cutters/flex-wing/ts10/
How much does it weigh? What is the length from tongue to tail wheel? Do the tail wheels on the wings fold in for transportation?
Base Weight of the TS10 is 2,190#, Tongue Weight is 720#. Overall Length from Tip of Tongue to Tailwheel is 162". Wheels do not fold in but Transport Width is only 93" which is less than 8' and that is going to be the widest point.
@@VahrenbergImplement Thank you,
Would this leave a finished cut if you keep your pasture grass well maintained?
I have customers that take a 4" grinder and sharpen the blades to create a more manicured look with Flex Wing Mowers. This way they do more of a cutting job versus beating action.
Vahrenberg Implement thanks
The wings don't automatically go below horizontal?
They will go below horizontal in the field but this single remote system is gravity fall and hydraulic raise for those that only have single outlet. Most flex wings are plumbed this way with single action cylinders. You could run hoses to both sides of the cylinder but would need more remote valves to operate the machine as double acting cylinders. Then it can put hydraulic down pressure on the wings and raise the center section. Not sure why you want to do that as most want to run in float position so the mower follows the ground contours.
Do you make one that can be used by a BX2380
For SubCompact Tractor like the BX2380 that is 23 Engine Hp or 17 PTO HP the RhinoAG TW14 Single Gearbox Machine is best choice due to Horsepower Limitations of those tractors.
I have a 25hp tractor , wonder would it work
25 Engine or 25 PTO HP Tractor? It require the minimum of 25 PTO HP to run the mower. You may need more HP to pull hills or for the lay of your land or soft ground conditions. I personally like 30 PTO HP but Rhino states minimum required is 25 PTO HP for flat,dry ground
Could a Ford 3000 diesel tractor 35 pto horse power do you think it would pull that probably up and down a big hill
Ford 3000 on Tractor Data shows 38 PTO HP Diesel, 37 PTO HP Gas. That is plenty to run the mower and that still provides over 10 HP for the Tractor to pull up contours.
what series john deere can pull this
We sell Massey Ferguson and do not keep up with all the Deere products but You need 25 PTO HP (Not Engine HP). Tractor Data is your friend to find out specs on all brands and to find out PTO HP to find the minimum tractor. Typically 40 Engine HP will get you into a tractor with at least 25 PTO HP. Tractor Data Website: www.tractordata.com/
How much does a unit like this cost
You need to contact your local dealer for pricing as it can vary based on freight rates in different regions of the country and also choice of options and how you want configured. Here is RhinoAG Dealer Locator: www.rhinoag.com/find-a-dealer/ If in West Central Missouri give us a call 660-584-2250
Sweet!
Awesome
I like to see it on a tractor will 25hp on pto to see if it works!
The Massey Ferguson 1742 in this video is 31.6 PTO HP. I'll hook up the closest PTO HP and shoot a short clip. Sold this exact package to a customer and he absolutely loves it and says it has more power than he needs.
Tractor Time with Tim did it on a 3033R which is in that neighborhood as well.
Here is link to that video: ruclips.net/video/XkLXQwM5XlA/видео.html
It was a 2038R which is 37 Engine/ 30 PTO HP he used.
Could I pull it with my farmall 450. I got power pistons and a preformance kit in it and it's push 71hp at the max on the pto and an average of 67hp
It only needs 25 PTO HP so you have plenty with the specs you given on the Farmall 450.
@@VahrenbergImplement huh i was thinking it'd need some weights on the front or wheel weights to counter the balance. It took some time getting that 4 cylinder to that much hp but I'm starting to think that my friends dyno is a bit off.
It's drawbar pulled cutter so it doesn't carry as much load on the tractor but a a properly ballasted tractor based on the task and load is always recommended.
How much does it cost?
Depends on some options but the way we been selling them with RhinoTrax Tires and Chain Guard in Massey Ferguson Red...approximately $10,500 selling price.
Did you say that the wings can mow at the 90° position?
And so if you have multiple hydraulic outputs, you could run one at 90° or 60° full time?
Operational Flex is 45° Up to -25° Down. You can plumb each wing to be operated separately One Up, One down or both up at 45° or any combination you desire or run in float position and the wings will float with the contour of the ground.
Made in the USA!
Made & Assembled in the USA! And over 90% of the Steel is USA Steel too! RhinoAG is one of the Great American Companies!
How much doe the ts10 cost?
Depends on how you equip. But I have one instock with RhinoTrax Tires, & Chains Guards for $10,300.00
Damn now there 20,000
TS10 with RhinoTrax and Chain Guards are $16,369.02 (2023 Pricing). Steel and Fuel have lots to do with rising costs. High fuel prices increase freight to dealer and everything shipped to RhinoAG Factory in Illinois to build & assemble. Increased Wages has effected cots to manufacture too.
Hey I build these in gibson city😁
AWESOME! You do amazing work!!! Thanks for building the BEST Cutters in the Business!!!
How much $
It's best to contact your local RhinoAG dealer as there are options for these cutters. Pricing varies by region so best to visit your local RhinoAG Dealer to get the best deals in your area. www.RhinoAG.com
Outrageously over priced.... That's why people are not buying.....
Just delivered another one this week. We have back log of orders for retails sales on TS10 Cutters. I could sell everyone I can get my hands on. Must not be overpriced with backlog of retail sales we have for them right now.
@@VahrenbergImplement I am glad you are selling...But there is a huge difference between a buyer and a Satisfied content buyer... what I mean by that is --- Buyer bought it bc he had to or it makes financial and practical sense...Rino,Bush hog are good products... but the price is Not.Thank you...
We have lots of repeat RhinoAG Buyers. Cheapest Price is not best value. Paying more for Quality and the Machine Last Longer and does better job is Better Value. I'm glad I don't sell cheap...I love selling products that last why we sell Massey Ferguson and RhinoAG. Quality Products and Great Value.