THIS ISNT REAL DYNO NUMBERS AT ALL ITS BELOW NORMAL VOLTAGE AND HE DIDNT EVEN DO .5 OHM WICH ITS RATED AT!!! HE SHOULDNT BE DROPPING THAT MUCH VOLTAHE AT ALL! I RUN FULL TILT AND DROP TO 14.7 VOLTS WITH 8,000 WATTS
@@SebastianS13bastian it's clearly rated at 1 ohm, not .5 ohm... The entire test is done at above rated voltage... This is obviously a real SMD dyno... What planet are you from haha. like seriously lol
@user-nf3ph7is7c what your not understanding is dropping that much voltage your losing alot of power. And at .5 ohm u get more power out of any amplifier!
Really impressive lithium bank with the two 180 amp chargers. Your voltage stays good under big loads. I definitely appreciate the solid videos. No filler, you just get right into it.
HOW IS THIS IMPRESSIVE OR REAL AT ALL??? 1 ALTERNATOR CHARHES HIGHER THAN HIS CHARGERS!! AND HIS POWER IS SHIT IF HES DROPPING THAT MUCH VOLTAGE!!!! IF HE STAYED AT 15 VOLTS AND RAN AT .5 OHM WICH ITS RATED AT!!! YOU WOULD SEE REAL NUMBERS
So you warm the amp up before testing? I'm curious if it makes a difference if an amp is warm, or if they usually perform the same "warm" or cold? Thanks.
Amps are typically room temp when put on the bench, and I do all the tests in one sitting. Most amps are at normal operating temperature after the first run.
I know these Taramps amps despise doing rated power, but I am interested in trying one on my dual 4 ohm HCCA 12" though for the mad efficiency. Currently running it off a HCCA3000.4H 4ch. I was thinking either a 8000w 2ohm or a 12000w 1ohm. I want that 8 ohm power, voltage is king! Shame above 8k models is only 1ohm. Might go a Stetsom ST-EX10500EQ-2 but being cheaper than Taramps, surely they're even worse...
Got a wolfram o series 8k that you can test. I'd love to see it on the dyno, and I'm sure a lot of others would also. I'll pay to ship back to me if you pay to ship it to you for dyno purposes only. I'll hold not responsible for anything that could happen during dyno. What do you say?
I've got the O5000 video uploaded just trying to hold a few days before I set to live since I just uploaded the JP23 video. I'd be happy to do the 8000 also, and I'll take care of it. Our contact info is on our about tab or you can send a message through the website. Thank you sir.
Como você não possui uma bancada de baterias suficiente para manter em 14.5v, deixa ela estabilizada em 12.8v, assim tanto em 1, 2, 4 ohms temos um resultado mais real, visto que o aumento tá potência é exponencial de acordo com a tensão.
I had one of these repaired and sold it, the person that bought it says when he connected it, it's going into protect mode but he sent me a video and he only had one ground on one side connected and one power on the other side not all four. Would this cause it to go to protect mode?
@Facekicker ok, yeah I looked it up in the owners manual this particular amp requires a lot of juice lol I was wondering why there was 2 inputs for power and ground...now I know
In real world use, very generally speaking, dynamic is the most like music. However, amps that seem to have exceptionally high dynamic scores on the dyno (2 or 3x certified) typically won't show those numbers on music when clamped in competition.
Mind truong 1k Hz load? Dont remember of you said it was @ 40hz or not most test that way which is cool just curious. I know the bass 12k isnt meant for 1khz all the same I wonder if itd blow it up or just cause a protect?
I would imagine it would work fine on 1kz, it's a full range amp. I have just converted my bank to CMAX and will be doing the big Taramps models again, I'll try to include a few full range dynos also.
Do you know if they discontinued the md12 1ohm models? I bought some half ohm version by accident and it’s been over a year and I still haven’t seen any 1 ohm versions for sale.
My Stetsom 7k does 6,004W @ 9.9V regularly, and has since 2012 when I bought it. (I don't have a strong enough batt bank, obviously, but, it doesn't care.) Wired .7 rising to a perfect 1 Ohm during burps.
Before I even read the answer I said yup. I have a 400 mechman charging a 80ah xspower lithium bank, that's running my SounDigital Exo-X 12k amp and trust me my amp Digs when the bass drops. Meaning seems like that's a perfect match. It's Pushing 4 X15's V2's.
Next amp that you should test is the new 3500rms watt cea Rockville dbcomp5 with a built in volt meter! Its $350 new and a Korean board as well! No one has tested this amp😀
@Chuck Holmes no I don't think its junk who knows I run old Hifonics amp and they still work. Now this guy tested this amp and I can't believe how many watts it put out.
@Chuck Holmes your probably right Rockville might be junk but this amp I hear is a good cheap China board that you can find on the China 3000 watts SAE Sundown buget amp they make. But personally I would buy a Sundown because there components or probably put together better.
@Chuck Holmes I like whatever brand I can afford. I once had a 15 punch stage 3 600 rms watt Fosgate way back in the day it was good I sold it for a 15 m5 Memphis and now my dad has it now in his Buick Roadmaster. My current setup is 2 18 Soundqubed on 2 Hifonics amps strapped.
@@d.j.theman7581 usually carelessness. Number one being the lack of necessary electrical, impedance being entirely too low, and excessive abuse of the amplifier such as heavy, and excessive clipping. I see a lot of short circuiting also, simply due to people mis-installing or messing with the speaker wires or whatnot while the amplifier is on. If a customer takes care of their equipment they will not have any issues at all whatsoever.
The reason why I ask that because I’m m running at 2 ohm with two 12 inch vfx and I don’t want to over power them to the point I will blow them so I can’t decide to get the taramp 8k md or the 12 k md
I know they make power but I've heard that they do blow easily and the build quality just isn't that great. Idk 🤷♂️ I think I'll spend more and get a little bit higher overall quality. Just my opinion.
@Facekicker yeah I'm still thinking, do I get a taramps 12k or just get another salt 8k or sell my 8k and get two salt 6ks. But if I can find a crescendo encore 12k that's not a bad plan at all.
My opinion is the Korean amps boards are built better than this amp. Next amp I might try is a 6,000watt crescendo bassclef at .5 ohms. I've heard at .5 there clear and put out over 8000rms watt clear watts. I only got around 3600rms watts of Korean amp power at the time. I got 2 older Hifonics 2000 cea Brutus amps back when Hifonics knew how to build an amp and its so clear 15hz even shakes my front doors on my no wall 2 18 in a long suburban!!!
Well I get the point taramps is good for the price. 2 question how much is a 12 taramp and dose it come in the bass line? I'm looking for a powerful bass amp not a full channel.
@@RyanBassForLife They don't make a Bass 12k. Only the MD12000 for $690 on Amazon. (Just use the built in electronic crossover if you don't want it full range) The closest Taramps in the Bass line is the Bass 15K for $1100... Not sure if it's worth $410 more than the MD12000. My gut says no.
@@RyanBassForLife In fact the MD12000 made 11177 watts where the Bass 15K only made 10458 on the same dyno. Save yourself $410 and get 719 more watts! MD12000 for the win!
I appreciate the no bull dyno vids and the honesty! Keep em comin
THIS ISNT REAL DYNO NUMBERS AT ALL ITS BELOW NORMAL VOLTAGE AND HE DIDNT EVEN DO .5 OHM WICH ITS RATED AT!!! HE SHOULDNT BE DROPPING THAT MUCH VOLTAHE AT ALL! I RUN FULL TILT AND DROP TO 14.7 VOLTS WITH 8,000 WATTS
@@SebastianS13bastian it's clearly rated at 1 ohm, not .5 ohm... The entire test is done at above rated voltage... This is obviously a real SMD dyno... What planet are you from haha. like seriously lol
@user-nf3ph7is7c what your not understanding is dropping that much voltage your losing alot of power. And at .5 ohm u get more power out of any amplifier!
@user-nf3ph7is7c In a real.wprld system pushing 16 volts and not dropping at .5 ohm you would see ridiculous high numbers way over rated!
@@MarkCornell-r8c They make multiple different ohm versions!
Really impressive lithium bank with the two 180 amp chargers. Your voltage stays good under big loads. I definitely appreciate the solid videos. No filler, you just get right into it.
Good my ass dropping in the low 12s is horrible
HOW IS THIS IMPRESSIVE OR REAL AT ALL??? 1 ALTERNATOR CHARHES HIGHER THAN HIS CHARGERS!! AND HIS POWER IS SHIT IF HES DROPPING THAT MUCH VOLTAGE!!!! IF HE STAYED AT 15 VOLTS AND RAN AT .5 OHM WICH ITS RATED AT!!! YOU WOULD SEE REAL NUMBERS
Finally I see a dyno on taramps im now a believer lol thanks for the video man keep up the good work ill like and subscribe
Those tweeters sound great in the background.
They don't they.
🤣 That's the Diamondboxx, I tried to keep the volume on it a tad lower for this one
I need a dyno for the .5 ohm version
Same here, I'm looking at the Deaf Bonce Apocalypse db3512s, but not sure if I'll get the 1+1 or 2+2 ohm.
Great dyno testing sir keep up the good work 👍 🙏🙏
How do like the build quality of theTaramps? Thinking about buying the 8k version.
Is this better to get than the bass smart 8
Damn that's Power 😮😮😮😮
Dude fuck Derrick at old school car audio amp dyno vids you got no bs to the point you the man bro subbing
So you warm the amp up before testing? I'm curious if it makes a difference if an amp is warm, or if they usually perform the same "warm" or cold? Thanks.
Amps are typically room temp when put on the bench, and I do all the tests in one sitting. Most amps are at normal operating temperature after the first run.
Would it be possible if we could get a DM 2500.1 dyno test. Thank you
Hi Facekicker do you have dyno test for md12k .5 ohm version?
I know these Taramps amps despise doing rated power, but I am interested in trying one on my dual 4 ohm HCCA 12" though for the mad efficiency. Currently running it off a HCCA3000.4H 4ch.
I was thinking either a 8000w 2ohm or a 12000w 1ohm. I want that 8 ohm power, voltage is king! Shame above 8k models is only 1ohm. Might go a Stetsom ST-EX10500EQ-2 but being cheaper than Taramps, surely they're even worse...
The md12000 is rated down to .5 ohm tho ?
Great content keep up the good work
Love it!
Got a wolfram o series 8k that you can test. I'd love to see it on the dyno, and I'm sure a lot of others would also. I'll pay to ship back to me if you pay to ship it to you for dyno purposes only. I'll hold not responsible for anything that could happen during dyno. What do you say?
I've got the O5000 video uploaded just trying to hold a few days before I set to live since I just uploaded the JP23 video.
I'd be happy to do the 8000 also, and I'll take care of it.
Our contact info is on our about tab or you can send a message through the website. Thank you sir.
@@Facekicker thank you sir
Yes I would love to see a dyno test with that amp too
Como você não possui uma bancada de baterias suficiente para manter em 14.5v, deixa ela estabilizada em 12.8v, assim tanto em 1, 2, 4 ohms temos um resultado mais real, visto que o aumento tá potência é exponencial de acordo com a tensão.
Babozeira existe em todo lado meu patriota kkkk esses babacas nem conhecem o poder desse modulo.
This one is pushing out more power than the taramps 15k?
From all of our testing.. yes.
I run my bass 15k @ 16v it’ll walk all over the 12k
I had one of these repaired and sold it, the person that bought it says when he connected it, it's going into protect mode but he sent me a video and he only had one ground on one side connected and one power on the other side not all four. Would this cause it to go to protect mode?
Possible yes
What about 0.5
Im getting the 0.5 ohm md12k soon to power 2 xv312d2s
What dual inputs are you using? I'm looking to get some for mine
Ill Kustomz sourced from Xplicit Audio
Jim's machine works
Dual imputs means you have to have each set hooked up to its own power source?
No
@Facekicker ok, yeah I looked it up in the owners manual this particular amp requires a lot of juice lol I was wondering why there was 2 inputs for power and ground...now I know
I have a question please: Which one of these tests depicts the amp playing music, certified, uncertified or the other one? Thanks
In real world use, very generally speaking, dynamic is the most like music. However, amps that seem to have exceptionally high dynamic scores on the dyno (2 or 3x certified) typically won't show those numbers on music when clamped in competition.
@@Facekicker Thanks for breaking that down for me😀👍👍
@@Facekicker sadly people can't grasp that concept. The hcca splx is a perfect example of people being stupid.
👊🤝
Are Taramps pretty reliable?
Yessir
Mind truong 1k Hz load? Dont remember of you said it was @ 40hz or not most test that way which is cool just curious. I know the bass 12k isnt meant for 1khz all the same I wonder if itd blow it up or just cause a protect?
I would imagine it would work fine on 1kz, it's a full range amp. I have just converted my bank to CMAX and will be doing the big Taramps models again, I'll try to include a few full range dynos also.
It won't send to protect, all it would do would be elevate the watts.
Do you know if they discontinued the md12 1ohm models?
I bought some half ohm version by accident and it’s been over a year and I still haven’t seen any 1 ohm versions for sale.
1 ohm models were replaced by the half ohm model maybe 2 years ago
My Stetsom 7k does 6,004W @ 9.9V regularly, and has since 2012 when I bought it.
(I don't have a strong enough batt bank, obviously, but, it doesn't care.)
Wired .7 rising to a perfect 1 Ohm during burps.
I call bs...
@@jermainephillips5179 Then, you called WRONG. 👈🏻
The amp has been doing that every show I attend, with no issue, since 2012.
Is 70 ah lithium and a 240 amp alt enough for this amp???
Ya
Before I even read the answer I said yup. I have a 400 mechman charging a 80ah xspower lithium bank, that's running my SounDigital Exo-X 12k amp and trust me my amp Digs when the bass drops. Meaning seems like that's a perfect match. It's Pushing 4 X15's V2's.
Yes it pulls 250 amps you should be able to get away with that 🤔
Can you test the md 12k 0.5 ohm version
Coming soon!
Any video on .5 ohm?
Is there a MD 8K dyno? 8000.1 or 8000.2?
I just started reshooting the Taramps amps
@@Facekicker cool I would like to see the MD8K @.5
Next amp that you should test is the new 3500rms watt cea Rockville dbcomp5 with a built in volt meter! Its $350 new and a Korean board as well! No one has tested this amp😀
Should have it in early next week
@@Facekicker thanks man "Black kia elite 12" wanted to see this amp dyno more than me but I really can't wait to see it as well I be waiting😀
@Chuck Holmes no I don't think its junk who knows I run old Hifonics amp and they still work. Now this guy tested this amp and I can't believe how many watts it put out.
@Chuck Holmes your probably right Rockville might be junk but this amp I hear is a good cheap China board that you can find on the China 3000 watts SAE Sundown buget amp they make. But personally I would buy a Sundown because there components or probably put together better.
@Chuck Holmes I like whatever brand I can afford. I once had a 15 punch stage 3 600 rms watt Fosgate way back in the day it was good I sold it for a 15 m5 Memphis and now my dad has it now in his Buick Roadmaster. My current setup is 2 18 Soundqubed on 2 Hifonics amps strapped.
Missing the amp clamo on this one. Is really. Like to know efficiency.
I was thinking about putting one of these on my 2. 12’ 6,000 watt hippos. What do u think
A bit stout but should be OK if gained right
Made un Brasil
Niiiiiiiice 😍
What causes them taramps to blow thou?
@@d.j.theman7581 usually carelessness.
Number one being the lack of necessary electrical, impedance being entirely too low, and excessive abuse of the amplifier such as heavy, and excessive clipping. I see a lot of short circuiting also, simply due to people mis-installing or messing with the speaker wires or whatnot while the amplifier is on.
If a customer takes care of their equipment they will not have any issues at all whatsoever.
Do you think the half ohm md12 can take a .25ohm load?
I would not try that
@@Facekicker 😆
@@Facekicker so basically I will never see 12k from this amp…wdyt?
@@Bigislandguy clamped in the lanes I've seen the do rated rising from 0.5, just not on the bench.
Still waiting for .5 ohm load
I think your power supply is dropping to fast. Your 15k and 12k had similar numbers.
We've got a new CMAX bank and will be revisiting the larger Taramps soon
I heard that because the md 12k is rated at 12.6 volts and the Bass 15k is rated at 14.4 volts. That the md 12k is stronger!👍
I didn’t know you run a 2 ohm load on this amplifier
You can wire lower.
This was on my AGM bank that barely supported 12k.
The reason why I ask that because I’m m running at 2 ohm with two 12 inch vfx and I don’t want to over power them to the point I will blow them so I can’t decide to get the taramp 8k md or the 12 k md
@@joemaxxcapri1799 MD8k is plenty for those. Make sure you have the proper electrical support.
What type of current did it pull
Right that’s my question
What kinda power do it do at 15.5
Well over 12k if rising to ~1 ohm
I know they make power but I've heard that they do blow easily and the build quality just isn't that great. Idk 🤷♂️ I think I'll spend more and get a little bit higher overall quality. Just my opinion.
These are great amps with a good protection circuit. They are actually less likely to fail than many other amps.
@Facekicker yeah I'm still thinking, do I get a taramps 12k or just get another salt 8k or sell my 8k and get two salt 6ks. But if I can find a crescendo encore 12k that's not a bad plan at all.
That's a lot of freaking reserve lol
what's the song in the background at 0:40 ?
ruclips.net/video/CWcStVxR5x4/видео.html
Do you have Mark's contact info? I have this same model amplifier that I need repaired.
Hey bro could I get ur amp repair man's info? I have a blown 5k that needs repair
MARK CANNADY
2205 DAIL RIDGE RD
WENDELL
North Carolina
27591
9194000195
anythingaudio32@yahoo.com
Want to sell this amp??
STARTING with the lowest impedance is somewhat anti-climactic.
No BS 💪
My opinion is the Korean amps boards are built better than this amp. Next amp I might try is a 6,000watt crescendo bassclef at .5 ohms. I've heard at .5 there clear and put out over 8000rms watt clear watts. I only got around 3600rms watts of Korean amp power at the time. I got 2 older Hifonics 2000 cea Brutus amps back when Hifonics knew how to build an amp and its so clear 15hz even shakes my front doors on my no wall 2 18 in a long suburban!!!
Should try it at 1ohm instead of .5
Nendo doesn't have a 12k only a 13k... 12k has been discontinued for years
Well I get the point taramps is good for the price. 2 question how much is a 12 taramp and dose it come in the bass line? I'm looking for a powerful bass amp not a full channel.
@@RyanBassForLife They don't make a Bass 12k. Only the MD12000 for $690 on Amazon. (Just use the built in electronic crossover if you don't want it full range) The closest Taramps in the Bass line is the Bass 15K for $1100... Not sure if it's worth $410 more than the MD12000. My gut says no.
@@RyanBassForLife In fact the MD12000 made 11177 watts where the Bass 15K only made 10458 on the same dyno. Save yourself $410 and get 719 more watts! MD12000 for the win!