Это видео недоступно.
Сожалеем об этом.
Stratocaster Guitar Build - Part 2 - Building A Stratocaster Guitar Neck
HTML-код
- Опубликовано: 7 сен 2012
- Template sets to follow along with the build - fletcherhandcra...
A complete construction diary of a Stratocaster style guitar being built from scratch. I will go into mind numbing detail on most things. Select 720P video quality, make a cup of coffee ( this 2nd video is 30 mins as well !) , sit back and watch in full screen.
Specs;-
Flame Maple Neck
Rosewood Fretboard
StewMac Spoke Style Trussrod built into heel of neck
12" Radius
Stew Mac medium fretwire
Tinted Nitro Lacquer
I cannot begin to understand why would someone stumble upon this channel and these video series and criticize and/or complain (thumbs down) about something. A top notch luthier sharing the knowledge he has acquired over the years for free! for free! but all of the sudden some people feel like they are owed explanations. In behalf of the many guitar enthusiast who appreciate your efforts, many thanks Fletcher.
+Andres Mena Thankyou Andres, I appreciate it
well said mate. This is a superb series of videos.
These are by far the best videos of Guitar Building on RUclips
If I.... when I win the lottery, i'm going to set up a workshop in a barn and build guitars. I'll also keep chickens and some goats. Just so you know.
Darryld1
Awesome, I'd like some goats running around my workshop too
i'm certain someone out there can arrange this. Careful what you wish for ;)
Darryld1 :-)
Zach Beyer jn
It's 2023 I still enjoy these video series over the years thanks Mr fletcher ❤️
I'm going through this series for third time now while finally building my own guitars. It's hard to believe these videos are 10 years old and are still the best and most thorough build videos I have come across on you tube. I hope you are well Mr. Fletcher and thanks for doing these.
Oddly enough, the background sounds of cars passing by and birds tweeting is better than any music you could have overlaid. So soothing to listen to you explain all of this. Thanks for posting, great vid!
Not sure how Fender, Gibson or other industrial luthiers do it but this kind of care and expertise can't be easily achieved or inexpensive. I hope Fletcher's guitars pay off and live up to the unusual workmanship and work put into them.
I picked up the neatest fret slotting rig a while back. My brother and I went to a thrift store and there was this ancient De Walt radial arm saw. I said, "Wow Dave, I bet that old saw is worn out and sloppy". I showed him how to tighten up the swing, height, and all the other travel points and she was still just tight as a drum and smooth as glass! Maybe .003" lash on the motor spindle! AMAZING for a 50+ year old saw! $50 US out the door! I can do 1 to 8 fret boards at once with it. I can also rip, miter, compound miter, and thickness saw with it too. I still have a super old Stanley Bedrock 150 back saw miter box I like too. I love your work. I see a lot of hacks on YT, but you, sir, are quite the artist!
I like how he explains what he is doing as he is doing it and explains the harder parts to exact detail
I've watched a ton of neck-building videos, and have to say I keep coming back to this series. I'm amazed at how labor-intensive some techniques are compared to this (which is already a lot to begin with). can't wait until I can actually START building...
I have been following this video series as a guide for my own project, and i must say it has been very helpful to me. I have learnt a lot from your videos. Also the quality of your work is brilliant.
Thanks Ross, glad you enjoyed it !
I watched the series in early 2012 and have since built three Strats, four Teles, one each 4-string & 5-string Jazz basses, and almost finished a triple Precision bass (wired like a Strat with a blender pot).
I would like to thank you David, you inspired me to take the step from tinkering with existing guitars to starting from scratch.
Jb kindly can you make or share your bass build knowledge with me.. Please❤️
@@johnmayer8906 It's hard to say in a few sentences. You will need a few tools of course, and a template for each model, or with patience you can make your own templates based on actual guitars.
I already had many years of power tool experience, which helps a ton. Routers are very dangerous animals, so are band saws and table saws.
My best advice is to watch David's Strat build, the same principals apply to all Fender style guitars and basses.
Also, if you're going to make the supreme effort, don't get cheap hardware, I use and recommend German made Schaller bridges and tuners, more expensive but worth it. If you have the skills, it's only a small step to winding your own pickups.
All this costs money of course, so start small and basic, but the deeper you get into it, the more you will understand and want the right workshop power tools. Best wishes my friend.
I never knew I wanted to work with wood until I watched these videos. Excellent.
You have all the right tools for the job and they're good ones, too. I'm envious but thankful you've shared these videos. Peace.
As someone who is going to learn to be a Luthier, these videos are helpful!!! thank you!
You don't want to be pressing or hammering frets in and find that the slot is not deep enough. Cut the slots slightly deeper than the tang ( allowing for the radius that will be sanded in). You will wick CA in from the sides, this will fill any gaps under the fret.
Extremely clean work, and phenomenal explanations. This was very valuable to me, and I thank you for the time you spent creating it.
HI Smitty, Yes, I used a dremel with a sanding wheel to remove excess wood on the fretboard where the rod sits. Look forward to seeing your bass build
I've checked many of your videos David, all by now I think. I love your very detailed and fiddly way of working. It's certainly a modus operandi that I appreciate. Wish you weren't in Australia tho. I'd gladly put down my money for having a private course. Cheers!
+ThomasUV777 Thanks Thomas, I appreciate the comments !
Your attention to detail is brilliant
If you only have Bunnings nearby, buy some Vic Ash / Tassie Oak , Most Bunnings keep that in stock. - It works and looks very close to mahogany but can be a little heavy. Pick some lighter pieces. You can use if for necks too !!
I just used what I had on hand. Its about 3mm thick. The thickness of the aluminum determines the thickness of your dots so just choose a thickness you are happy with. You don't want the dots too tall, its just more work to sand them down to the fretboard
you should man, its a great community, and your expertise would be GREATLY appreciated there.
very nice results. the way i do my inlays is a little different but gets the same results. i drill my holes before i radius the fret board. then after glueing the inlays in, ill put my radius on it so i just have to sand once. like i said though, to each their own and you do really nice work. i just built a strat for a buddy with a pine body and walnut neck with pine fingerboard and it turned out really nice..was jealous to give it away haha. love your videos man
you have the cleanest workshop iv ever seen very impressive
Sir, you not only have the most amazing skills, but the most amazing tools as well!
Several lessons learnt here, tyvm!!
Hi, Not at this moment, I have too much going on in the workshop for the next 6 months at least to even consider repairs. Sorry ! Glad you are enjoying the video's
You sir, are a hell of a constructor.
I hope you are marketing this on DVD? Because you are very good at making instructional videos. Now I understand why a good neck is so expensive. Thank you for the great information.
Awesome ! Chambered body with drop top is definitely the way to go . Tassie Oak is a really nice wood.
this looks the most difficult part of building guitar. I always wondered how the fret can be set to proper position.Thanks for the vid.
Major respect to your craftsmanship. Your accent is entertaining also!
This is why custom guitars cost so much money. You are a great craftsman David!
If there is the most complex way of building a strat guitar neck, this is it!
Professional,precise...clean work..no mistery....friendly and helpful...5 stars for your videos..greetings from italy:)
Thanks Suezo !
You do beautiful work sir,I love watching your Vids.You are a true old world craftsman.I see a hell of a lot of passion and care in your work.
I would love to own one of your LP juniors in TV Yellow.
thats a beautiful piece of material for the neck.
Thankyou , I'm glad your enjoying the video's
Hi, Most of my stuff comes from USA ( Maple / Rough fretboards ) but I buy Mahogany locally - Trend Timbers, places like that will sell it. I'm getting more into Australian timbers now, I have some beautiful slabs of Qld Maple that will make some beautiful guitars.
Awesome precision, the instrument must be a pleasure to rock!
I got a radial arm saw so I can radius first or build a real strat neck with a skunk stripe and a maple fret board that is not glued in, or even slot 6 boards at one time. The radial arm saws from the 1980s have a small enough motor housing the Stewmac 6" blade clears with ease. The radial arm saw has become rather obsolete or at least less popular now that compound sliding miter saws came out. The radial is safer when used properly (knock on wood). Hand slotting properly makes a better product.
A little acetone cleans up the super glue sqeeze out but move kind of quick.
Really nice detailed video. Couple techniques like the fretboard alignment pin I've read about but never seen someone demonstrate. I'm going to try some of these on my next build.
I really want to thank you for the high level of detail you put on these videos. You are awesome!
I've read that the old Fender dots were everything from wood filler to fiber board so there is some dispute as to what they used to use. The polymer clay I use can be bought in lots of colors so its a cool option for colored dots you would not otherwise be able to buy.
oh man I wish I had a table saw like you to slot the frets. Doing it by hand is so much harder… Basically I measured the fret slots with a pencil, then cut a thin slot with a cutter as a guide for my saw, and now I’m cutting the fret slots with guides on each side of the marks I did with the cutter. I hope I won’t screw everything…
I've been searching for a vid about this for a while haha. Never found any adressing the silicone and that kind of stuff. Awesome vids. I subscrided immediately :) Cheers mate, keep it up
nice videos and well explained, with typical aussie simplicity and crafting. well done man
This vid never gets old... Thank you for a greart tuturial. MangoHead Likes
I use a stewmac depth gauge to check the slots out before fretting as you do - I slot deep enough that I usually don't need to adjust anything. I don't see any benefit in radiusing the slot to match the fretboard. I wick superglue down the slot too
All in all good vids. While I''d do some things different the key takeaway for me is having a procedure to be efficient and maintain quality. There's no guesswork here.
Absolutely , if the board is off centre, your radius will be high on one side and low on the other.
Great David.....just great
Jig for sanding radius is simple genius.
I'm building my own guitar which should be done by late September/Early October. It's going to be a Les Paul but with Stratocaster controls.
Part 2 of my 10 part Stratocaster Build
why no filler strip for truss rod ?
What for ? Its a dual action truss rod
where are you getting your exact dimensions for the body, neck, head, ect.?
Dictated by the templates I am using
Pleeeaase, take me to work like helper.
Sounds like a fun project !
Excellent series.
i got some tassie oak for a body and neck. bit heavy (like you said) so i might do a chambered body with a drop top. thanks for the advice mate!
You're doin the fret marks the hard way. Just make an x. Where the lines cross is the center.
He explains that method... Center marking with an X on a small measurement like the frets is imprecise due to the variable thickness of pencil lead and marks. Little deviations will compound to off center your hole. He's showing you the most accurate way of doing this.
Your build skills are amazing. Fine details, concise time saving valued tips. Close attention to detail. You should be teaching this stuff. I recently sent an email to Stewmac regarding a magazine for build techniques etc.much like Woodsmith magazine. You would make a great contributing editor.
You may not be aware of this but there is a site that sells band saw blades to cut fret boards, the blades are $15 or 17 U. S. but if you are in Australia the shipping will be more, in the U. S. this company charges a flat rate of $5 no matter how much you purchase from them. I will have to get the site link if you would like to have it.
Awesome! Always looking forward to your next video.
...for a friends costume at comic con in new york. It's a guitar rifle from last man standing . The guitar doesnt have to work, but i think it would be awesome if it did. First time making a guitar.
Hi Fletcher! First let me commend you on this channel - it is awesome!!. I am a newbie guitar maker and half way through my first Telecaster. I have put a tv in my workshop so that I can watch your videos to ensure that I am following correctly. I too have a stumac table saw blade (but had to have the centre laser cut larger for UK table saw 30mm) I have tested it out on some waste wood and it works fine. What depth will I need to cut for the fretwire? I have been told that a medium fret wire will suit my playing ability lol. Keep up the good work!!!
Acoustic guitar builders use double sided tape for almost everything. But, if you don't do wood working at all you may never use it much. It is very handy for many things.
I use the stuff designed to suit general weather sealing
@David Fletcher Cause I also want to add binding, change nut and something in the neck is moving if I turn it upside down
Would you consider doing a video on a compound radius? E.g. 7.5 to 12 or something? That would be really helpful. Thanks!
Fletch, I love your videos and appreciate your efforts doing this beautiful work. A word about polymer clays, if possible, avoid using your main cooking oven as the clays release toxins.
Thankyou ! I didn't know that
Great videos mate. Appreciate the detail!
Excellent videos! But I have a question, what (besides from the silicone) keeps the truss rod from sliding back and forth? Since it's not anchored at the headstock end of the neck.
I do when I'm using single coils such as I will be in this build - I'll cover it in detail in a later video so stick around
I could be wrong but I think that by putting the truss rod in with the tightening rod on top is wrong. Doing that will cause the neck to bow in instead of back. The idea behind the double truss rod is to eliminate the need of carving the truss rod cover, which is usually put in after the truss rod and before the fret board. I am not an engineer but I think that by tightening the one rod it will cause the other rod to bow away from the tightening rod from the center point, which in this case will cause the neck to bow forward and not back.
that looks beautiful amazing job
great video not mind numbing. very enlightening . thanks i learned alot
Do I think the depth of the fret slots affects the sound of the guitar ? - Not at all. I think the pickups and amp make the sound of the guitar, the depth of the fret slots wouldn't even factor in. Thanks for watching.
Terrific series, Mr. Fletcher!
Any chance of you building a bass like in these episodes?
This is an amazing tutorial! I'm building a prop for a friends
Thanks Tom
When ever I'm upset at something I usually work on building a guitar
Hi David. I'm currently working on my third built and I always come back to your videos for guidance, so thank you for sharing what you do. I would like to ask you how you avoid the taper towards the end of the fretboard's side after applying the radius since I didn't notice the sale taper I get with the 12" radius in my guitars. Thank you!
Remove the frets, drill the dots out, re-radius then replace the dots, sand smooth then refret. Probably easier to buy a new neck to be honest
Excellent. Thanks for sharing,
Somebody buy this man a new pencil!
i find this tutorias very usefull, i just broke my guitar neck, and i cant afford a new guitar so, i think im going to try this..
No, Trent Timbers in Sydney - Give 'em a call, they might be able to freight some timber out to you.
great videos man I love them super helpful.
Man, this probably the best build series Ive ever seen. Are you on projectguitar com by any chance?
The clay dot making is very cool. I wasn't aware till know that Fender use to use them. Do know if other manufacturers used them?
Great job!!! Bravo!!!
I'm building a guitar in my woodworking class at highschool and using your videos as a guide. So far it's going excellent, your videos are incredibly helpful! I am having one problem though. I've routed the truss rod channel and the little brass blocks are sitting down right where they should, flush with the surface of the neck. However, the chrome barrel just before the spoke sits about the face of the neck. I've routed for the spoke but the fretboard still wobbles because of that little barrel part. Should I just sand out a little section for it? Will that be a problem when I go to fret the guitar? I'm not sure if this happened on your build, I couldn't see. Maybe they changed the design since you uploaded. Any feedback would be appreciated, and thank you so much for making this awesome series, you've inspired me to become a luthier!
you need to sand a channel on the back of your fretboard for that little chrome barrel to sit. For some reason, it got edited out of this video. The fretboard needs to sit flush on the neck blank before gluing. Good luck with your build !
*****
Thank you!
I really enjoy your tutorials, you're an excellent luthier. Why is your Strat a 21 fret and not a 22 fret? Have you ever built any left handed guitars? You should build a guitar for
fellow Aussie, Courtney Barnett.
Regarding this truss rod configuration is any allowance made at the nut end of the truss rod channel to enable the protrusion of the threaded part of the rod tbrough the end block? I couldn't see that on the video. Without is there a danger of the rod pushing itself out at the heel end on adjustment? Brilliant videos btw and best on YT IMHO.
If this trussrod got a problem, can you pull out and put a new one without remove the fingerboard?
Just for curiosity and practice!
Great video!
Thank you for this excellent series. I have a question: How do you get the slot depth equal as you move up the neck as when you radius the fretboard, the depth of the slots will become shallower and shallower due to the outward taper of the neck toward the heel with this tablesaw jig method?
Ok, I didn't watch the video where you showed the aligned marks, I skipped around a bit, I drew two marks on the upper neck to represent the nut, you align the back of the nut area with the first line I drew and not the second according to your video.
Excellent tutorial. I was wondering why you wouldn't insert the fret markers before you do the radiusing?
Ray Perkins You could definitely do it that way as well
I so wanna make an electric guitar....
But I have no money, and I have no tools...
Make some money, buy a good kit, preferably one without pickups and hardware because you will want to toss those anyway.
I have no tools and no money to buy tools, but I've found that there are carpentry coworking workshops, where you can just rent a space (and all the tools you need) for quite a low price.
Nice one!can you please tell me the thickness of the neck and the fret board,thanks men
Nice work, and what a brilliant tutorial! How long does it take in work hours? I Think I know what I'll be doing this summer! Thank you!
Approx 60 hours
Thank you, sir!