I've tried a few pumps, including this pump from you, and they all don't hold the gas for long. The pressure on this pump is also too small. The rest looks good. Maybe the capillary tube could be too long but otherwise it looks good, keep it up!!
The purchased air pump will leak air. Disassembling and resealing it may be a good solution. I am trying to make a new air conditioner. Big thank you for your wonderful and supportive comments. Have a good day!😀
Not enough power in the compressor, if it had the right temp/pressure it would blow the tubing off the condensor or melt the plastic. Next the metering device has to many wraps and the length of the copper tubing after defeat the purpose, immediately after the metering device should be the low pressure low temp side(the evaporator). In either case you are moving heat what 6 inches away tops and the configuration of those coils for the evaporator and condensor are not efficient. If you look at your ac unit you will see aluminum fins, this is to more efficiently absord and disipate heat. But moving the heat to the same room only adds heat not remove heat because the motor being used as a compressor generates heat.
Definitely possible. I like how u kept the evaporator coil ID greater than condenser coil ID and attached to correct suction and compression orientation That capillary expansion valve is also good. I have seen this on old school fridge repair work. That fridge is still working like a charm without the thermostatic expansion valve. Butane and propane are very efficient refrigerant but not commonly used due to flammable. You just need to have a functional thermostat cut off mechanism. And thermal separation to make it more efficient. I am still confused about what that injection is doing. Because once you open the valve the piston will fly. Sounds weird but Yes you can use that injection as a manual assist to accelerate the process. As the pressure inside will lift the piston and pressing it can instantly boost the compression as there is already NRV present on the pump. But best of luck with sour thumbs. 😂😂. . Good work bro
The syringe serves two purposes: firstly, to test whether the valve is leaking, and secondly, to manually increase pressure. Thank you for your attention and comments. Have a nice day!😀
Show real video of icing and condensation, it’s impossible to make ice on such low pressures. Even for the butane gas with boiling point of -1 and higher Enthalpy it still needs a lot of pressure 200 to 250 psi on condenser and 50 psi around the evaporator after capillary. The plastic TuBINgs can’t able to handle such higher pressure, how can you make it make ice on The evaporator? THE small diaphragm pump u are using is just capable TO make high enough around 50psi or some near 80 psi even this is too much for a small pump. If you are really confident enough show the condenser temperature and evaporator tempreature without zooming and editing the video raTHEr Than showing Fakes !
THE MODEL shows how an vapour compression system works , BUT YOU CAN MAKE IT WORK in reality ALSO JUST USE A BIGGER SIZE COMPRESSOR pump or preferably use a mini 12v rotary vane pump. Its will definitely work , you will get temperature differences on both high and low sides. You can also use a mini piston pump having compression ratings above 150- 200 psi . It works !
@@BillMingLabs⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran
The thing I still cannot get in such youtube toy friges is why the evaporator is always air-cooled, when it has to be a condenser as in regular friges?
7:30 look at the water on the edge of the copper pipe get frozen because the video is going backward means its fake. Whole process is fake All you can do is report this video as fake info . I just did
hi friend I really want your answer why a lot of people writing it is fake, I trying to make it, it took a lot of time from me but today I reach point to make it work it is really difficult I don't know what's wrong I did, please if you can help me, I spent a lot of time and money and thank you.
Great video, i just want to ask why u made 3 different size of coils, i saw it on other videos too but dont know the reason for it, can u please tell me
The video just showcases the operating principle of air conditioning. The thickest is the evaporator, the thinnest is the capillary, and the medium-sized is the condenser. The condenser converts high-pressure gas (refrigerant) into high-pressure liquid; Capillary tubes transform high-pressure liquids into low-pressure liquids; The evaporator converts low-pressure liquid into low-pressure gas. A pump is a compressor that converts low-pressure gas into high-pressure gas. Butane is a refrigerant (Danger! R22 is recommended).
So I see a lot of comments here, but no one stating the obvious truth... The air conditioner would do nothing, since it's not exhausting the hot air outside. The hot coil needs to be on the outside. Otherwise it's simply not possible
It would be good to cool a can of drink but aircon no. I agree. It's not venting to an external place so would increase the rooms temperature over time with the heat from components and motors.
I've tried a few pumps, including this pump from you, and they all don't hold the gas for long. The pressure on this pump is also too small. The rest looks good. Maybe the capillary tube could be too long but otherwise it looks good, keep it up!!
The purchased air pump will leak air. Disassembling and resealing it may be a good solution. I am trying to make a new air conditioner. Big thank you for your wonderful and supportive comments. Have a good day!😀
Not enough power in the compressor, if it had the right temp/pressure it would blow the tubing off the condensor or melt the plastic. Next the metering device has to many wraps and the length of the copper tubing after defeat the purpose, immediately after the metering device should be the low pressure low temp side(the evaporator). In either case you are moving heat what 6 inches away tops and the configuration of those coils for the evaporator and condensor are not efficient. If you look at your ac unit you will see aluminum fins, this is to more efficiently absord and disipate heat. But moving the heat to the same room only adds heat not remove heat because the motor being used as a compressor generates heat.
I think I'll take your advice. Thank you for commenting! 😀 Good luck!
Definitely possible.
I like how u kept the evaporator coil ID greater than condenser coil ID and attached to correct suction and compression orientation
That capillary expansion valve is also good. I have seen this on old school fridge repair work. That fridge is still working like a charm without the thermostatic expansion valve.
Butane and propane are very efficient refrigerant but not commonly used due to flammable.
You just need to have a functional thermostat cut off mechanism. And thermal separation to make it more efficient.
I am still confused about what that injection is doing. Because once you open the valve the piston will fly.
Sounds weird but Yes you can use that injection as a manual assist to accelerate the process. As the pressure inside will lift the piston and pressing it can instantly boost the compression as there is already NRV present on the pump. But best of luck with sour thumbs. 😂😂.
.
Good work bro
Can i use diagraphm pump as the compressor?
The syringe serves two purposes: firstly, to test whether the valve is leaking, and secondly, to manually increase pressure. Thank you for your attention and comments. Have a nice day!😀
Это не может работать.
Это фейк.
Wherever the air vents go, the two vents of the air motor are almost closed, and on the other hand, it can hold air, brother.
Thanks for watching and commenting. Have a nice day!😀
Show real video of icing and condensation, it’s impossible to make ice on such low pressures. Even for the butane gas with boiling point of -1 and higher Enthalpy it still needs a lot of pressure 200 to 250 psi on condenser and 50 psi around the evaporator after capillary. The plastic TuBINgs can’t able to handle such higher pressure, how can you make it make ice on The evaporator? THE small diaphragm pump u are using is just capable TO make high enough around 50psi or some near 80 psi even this is too much for a small pump. If you are really confident enough show the condenser temperature and evaporator tempreature without zooming and editing the video raTHEr Than showing Fakes !
Thanks for your comments. Have a good day!😀
THE MODEL shows how an vapour compression system works , BUT YOU CAN MAKE IT WORK in reality ALSO JUST USE A BIGGER SIZE COMPRESSOR pump or preferably use a mini 12v rotary vane pump. Its will definitely work , you will get temperature differences on both high and low sides. You can also use a mini piston pump having compression ratings above 150- 200 psi . It works !
@@hatwaradityasubhash8987Great idea😊
Deveriam ser proibido esses tipos de vídeos fake. Muita gente acaba acreditando
@@BillMingLabs⚠️ God has said in the Quran:
🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 )
🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 )
🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 )
🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 )
🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 )
⚠️ Quran
Nice
Can you create a list of parts and were to get them from?
Air pump price link
ये सब सिर्फ यूट्यूब पर ही मुमकिन है
It's real ?
I am making a new better one. Thank you for watching and commenting. Good luck!
Does this system really works, please tell truly as I want to invest in it. Thanks
I am trying to find ways to enhance it. Please feel free to follow my new video. Thank you for your views and comments. Good luck! 😀
@@BillMingLabsşu durumda ne kadar ise yariyor
Он ушёл от ответа заметьте! ☝
Johnson Jeffrey Thomas Richard White Sarah
Reporting done 👍 For fake things and not detail conclusions
need 4-8 bars to liquify on butane. I succeeded with car tyre compressor. There is a video on my channel
DIY refrigerators running on butane. Fake videos with water pumps. With an air compressor works -3C.
Great job！👍
😳😬😵💫😵💫😵💫 Nice, but I would rather have s heat stroke than listen to that damned thing all day... 🙈🙈🙈
Thank you for wathing. Have a good day!😀
👉How To Make A Freezing AC From Peltier For Both Room And Car | DIY Air Conditioner
ruclips.net/video/Uwq3ZmnIv7Y/видео.html
La chaleur va aussi dans la pièce mais bonne idée
This one I tried and it doesn’t work. Don’t wast your time and money
Thank you for your comment. Have a good day!😀
How long does one butane fill up last before you have to refill again? Looks pretty cool!😎
how long to work with gas
the gas temperature in the pump is very high. it can break down quickly.
You are right. I am making a new one. Thanks for watching and commenting!
Como funciona
This is the principle of air conditioning.Condensation releases heat, evaporation absorbs heat.
He put nitrogen inside copper pipe that's why you see ice. Its definitely a fake video
Thanks for watching and commenting😀
The thing I still cannot get in such youtube toy friges is why the evaporator is always air-cooled, when it has to be a condenser as in regular friges?
This is a good question. Thank you for watching and commenting. Have a good day!😀
does it really work or is it just a staged video???😢😢😢
Thank you for watching and commenting. I am making a good new one.😀
young man, you must learn to stick with tin
7:30 look at the water on the edge of the copper pipe get frozen because the video is going backward means its fake. Whole process is fake
All you can do is report this video as fake info . I just did
Even initially you would have put butane gas directly through the valve itself no need of inserting with the syringe.
I added this syringe to detect if the valve is leaking air😀
@@BillMingLabsgerçekten ne kadar süre ise yarıyor yada ise yarıyor mu
hi friend
I really want your answer why a lot of people writing it is fake, I trying to make it, it took a lot of time from me but today I reach point to make it work it is really difficult I don't know what's wrong I did, please if you can help me, I spent a lot of time and money and thank you.
But the ... Temperature is not getting low... .. Just 25.5......
Thank you for watching and commenting😀
Komae
got parts list
What is the name you have to vacuum it down
Great idea
Fake
Thanks for watching and commenting😀
El ventilador suele ir en el intercambiador de calor 😮
Thank you for watching and commenting😀
Something
😀
是使用真空幫浦嗎
我用的是大功率空气泵，12v 2A的，不是水泵。
@@BillMingLabs 好的 謝謝
get spray and seems as like snow :)))))))
Thank you for watching😀
Creative video, thanks :)
Thanks for your comment.Have a good day😀
Great video, i just want to ask why u made 3 different size of coils, i saw it on other videos too but dont know the reason for it, can u please tell me
The video just showcases the operating principle of air conditioning. The thickest is the evaporator, the thinnest is the capillary, and the medium-sized is the condenser. The condenser converts high-pressure gas (refrigerant) into high-pressure liquid; Capillary tubes transform high-pressure liquids into low-pressure liquids; The evaporator converts low-pressure liquid into low-pressure gas. A pump is a compressor that converts low-pressure gas into high-pressure gas. Butane is a refrigerant (Danger! R22 is recommended).
@@BillMingLabs I see so it's like a condenser?
Not worked
Time lost
Thank you for commenting😀
@ElectroBOOM
Bhai Ghar pe aagg laganeka erada ha kiya
Butane is flammable. Do not imitate😀
So I see a lot of comments here, but no one stating the obvious truth... The air conditioner would do nothing, since it's not exhausting the hot air outside. The hot coil needs to be on the outside. Otherwise it's simply not possible
Thank your for watching and commenting. Have a good day!😀
It would be good to cool a can of drink but aircon no. I agree. It's not venting to an external place so would increase the rooms temperature over time with the heat from components and motors.
Intuitively illustrates the working principle of air conditioning👍
Thank you for your coments😀
👎
fake
Thank you for watching and commenting😀
@@BillMingLabs your dad and your brother are the same person