OMG I don't have to wait another decade for these old carcasses to become valuable enough to justify a trip to the repair guy. I think I can pull this off. 🤘
I was searching video for the voice coil height should be. But I did not find on RUclips. Finally i saw you video and found my answer . You are amazing man .❤️
Searched through but can't find Part 2 for this video... also if listed as a "how to" you should flash up on the screen what glues/solvents are being used.
ive done this its fun.. i even stole voice coils and cones from a 12" speaker and sized down to a 10" speaker ..if the voice coil fits esp old jbl's jensens etc
Pay attention he measures to the very botton of the voice volt pole-- lt (the woofer) WILL NOT GO DOWN IT CAN ONLY TRAVEL UP:. THIS WILL CAUSE KNOCKING AND IN VERY FEW SECONDS 1. VOICE COIL BENDS..2 VOICE COIL TRYING TO MAKE THE DOWN STROKE....CANNOT IN SECONDS WILL OVER HEAT, SUM OF WHAT I WROTE HERE 'FAIL!
Yes, I think your adhesive is fine. The spider is not. I am a former loudspeaker engineer, and I have built and rebuilt countless amounts of loudspeaker drivers and prototypes. I have performed countless lifecycle and evaluation tests of components and complete drivers in a laboratory setting and real world placement. This spider is brittle. No type or amount of glue or adhesive at the voice coil former to spider junction will reverse the heat damage that has already occured. Further more, all of these replacement components will alter the frequency response band Thiele Small parameters of the drivers. The weight, shape, substrate, density, r and rigity of the cone, dust cap will effect everything about the driver. Sure it might make sounds, for a while but it will be different .
@@victorjbarker hey Victor I have Yamaha NS4 speakers one of the drivers woofer has separated from the voice coil. As such I am able to pull the magnet off the back. I read it might be possible to reglue? Any ideas?
Dear Alfred kindly let us know which glue (black) you used, bcuz all my Coral drivers have been made using same or similar black glue & I need to repair few drivers so it will be nice to know about the black glue's pros.
You can use 'pitch' which is a tar based derivative and sets hard glassy OR as I have to fix the cone etc simply cyan late adhesive commonly superglue WITH care.. I've also used a ceramic paste.. 👀
Aquí los materiales : en el primer gotero con meados o cualquier chingadera qué remueva el cartón viejo 2 comprar una bobina China qué entre en el hueco 3 chapapote negro o un chicle a medio masticar para qué tenga un bajo muy abajó pegar todas estas porterías y listo
Could you explain what you are doing and where you got the stuff you are using? I'd really like to learn and it's obvious you have some good knowledge! Thanks for the video though, it's good to at least see the process!
That is weak it will break on heavy bass .u shud have pulled off the spider and make a tight fitting with the coil before getting it back or use a new spider that fits tight.
Gives you the jist I guess.. Assumes watcher knows quite a bit... Nice overview but I guess I'll be going elsewhere for a proper lesson. Nice music though..
Thumbs down . I hate these videos where there is no explanation . I guess they expect you to already know . Going to find a video where someone knows what they're talking about.
En el vídeo se muestra como se cambia:,la bobina y el cono,,se hace una pequeña pestaña con cartón, lo más al ras de la bobina y la membrana,ya que la membrana es más grande y el pegamento podría adherirse a la canasta, se recomiendo utilizar pegamento epóxico para uso en membrana y bobina ya que es donde hay más fuerzas y pegamento amarillo (5000),pegamento de cola o de contacto para pegar hacia la canasta,como la membrana en parte externa,cono en la orilla de canasta Y las juntas que sujetan al cono
OMG I don't have to wait another decade for these old carcasses to become valuable enough to justify a trip to the repair guy. I think I can pull this off. 🤘
what is
Jur mammy
I was searching video for the voice coil height should be. But I did not find on RUclips. Finally i saw you video and found my answer . You are amazing man .❤️
I love seeing old things fixed!! Cool!
Good job showing the steps. I understand better now.
Thank you very much
Opooiiiuyyytrrreewwwwqqq...
Eploiiuuyttrrrrreeewwqqwqwpkoiuytttttrreewwqa
P
Njj
I know you did all you can to save the spider damper but it will be best to have the new one installed
Searched through but can't find Part 2 for this video... also if listed as a "how to" you should flash up on the screen what glues/solvents are being used.
T Robinson gay and ugly
ive done this its fun.. i even stole voice coils and cones from a 12" speaker and sized down to a 10" speaker ..if the voice coil fits esp old jbl's jensens etc
عالیه من صد تا کلیپ دیدم تا با کلیپ شما فهمیدم که چقدر باید سیم پیچ را درون آهن روبا قرار دهم
Pay attention he measures to the very botton of the voice volt pole-- lt (the woofer) WILL NOT GO DOWN IT CAN ONLY TRAVEL UP:. THIS WILL CAUSE KNOCKING AND IN VERY FEW SECONDS 1. VOICE COIL BENDS..2 VOICE COIL TRYING TO MAKE THE DOWN STROKE....CANNOT IN SECONDS WILL OVER HEAT, SUM OF WHAT I WROTE HERE 'FAIL!
Ez egy igazi kokányolás!
Always I confused,,the coil position inside magnet, but now I clear that, nice great video. Thank you dear🌷🌷🙏🙏👌👌
I like the music 😀
amazing job broo....
This linen spider assembly will not last. It has degraded and become brittle from heat damage. This needs to be replaced during the re-coning process.
I used a special adhesive for the speaker ...
Yes, I think your adhesive is fine. The spider is not. I am a former loudspeaker engineer, and I have built and rebuilt countless amounts of loudspeaker drivers and prototypes. I have performed countless lifecycle and evaluation tests of components and complete drivers in a laboratory setting and real world placement. This spider is brittle. No type or amount of glue or adhesive at the voice coil former to spider junction will reverse the heat damage that has already occured. Further more, all of these replacement components will alter the frequency response band Thiele Small parameters of the drivers. The weight, shape, substrate, density, r and rigity of the cone, dust cap will effect everything about the driver. Sure it might make sounds, for a while but it will be different .
@@victorjbarker hey Victor I have Yamaha NS4 speakers one of the drivers woofer has separated from the voice coil. As such I am able to pull the magnet off the back. I read it might be possible to reglue? Any ideas?
تشکر از برنامهای مفیدتان
Good job and very nice music Good luck
Dear Alfred kindly let us know which glue (black) you used, bcuz all my Coral drivers have been made using same or similar black glue & I need to repair few drivers so it will be nice to know about the black glue's pros.
You can use specialized glue sold in speaker component stores. that glue mixes with Asiton
You can use 'pitch' which is a tar based derivative and sets hard glassy OR as I have to fix the cone etc simply cyan late adhesive commonly superglue WITH care.. I've also used a ceramic paste.. 👀
What type of fluids are you applying on it
It's a specialized speaker glue sold in stores
Where do you get the voice coil? How do we make it ourselves? materials and calculations for 4 or 8 ohms
You can make coils but it is very time consuming. You should buy it at an electronics store
Wrap 10 winds around yer bell-end.
@@AlfredH can't buy when you're placed in a remote jungle like me. Everything has to be done by oneself
Very nice
I'm gonna try and do this with my advent legacies, I fried the voice coils listening to megadeth at full volume when I was drunk lol
Oh
You may not have done it properly
thumbs down for absolutely no explanation even though you obviously have a mic. must be a non-speaker person.
freemason douchebags are sworn to silence by the great talmudic loan shark
Exactly what it looks like, he repaired a voice oil without removing the old spider
It would have been nice to tell us what he was doing but instead he kept silent
Hey cool, mutes getting in on making youtube vids now
What do you use to lubricant the gum
Aquí los materiales : en el primer gotero con meados o cualquier chingadera qué remueva el cartón viejo 2 comprar una bobina China qué entre en el hueco 3 chapapote negro o un chicle a medio masticar para qué tenga un bajo muy abajó pegar todas estas porterías y listo
Te la bañaste bro 😁🤭
Amazing video
Dear sir happy Teacher's Day to u.
And sir what is the Transparent lequide u r using at the beginning ?
It's a solution: ACETON.
specialized for removing speaker cones
Alfred nail polish remover.👍
As always, amazing work Alfred! Thank you, sir!
Could you explain what you are doing and where you got the stuff you are using? I'd really like to learn and it's obvious you have some good knowledge! Thanks for the video though, it's good to at least see the process!
Yes, why no narrations?
That is weak it will break on heavy bass .u shud have pulled off the spider and make a tight fitting with the coil before getting it back or use a new spider that fits tight.
I almost didn't notice the footnote explaining what liquid to use... That was close..
UK on 17.9.18 What is the glue please
Aap kon sa glue use kerta hai . please glue ka name bataiye
Alfred help do i have to solder those two wires to something at the end please ?
You soldering those two wires to an isolated PIP on the speaker chassis
I'm guessing -using pitch (tar - coal compound ) with acetone mix which hardens the mix when set. 👀
WORST suggestion. ANY adhesive but tar.
Não seria mais fácil troca a aranha ficaria um serviço top👍👍
What white and black stuff is he using???
is the glue that attaches the speaker ribs
What is the name of this adhesive?
you can use any brooch speaker
The speaker's watts is not related to the capacitor value. thank you very much
sir what is coil wire gage..30..33.36
Gives you the jist I guess.. Assumes watcher knows quite a bit... Nice overview but I guess I'll be going elsewhere for a proper lesson.
Nice music though..
I saw what happened. Watch it again. 🔊😸🕪
hello I am looking for a kit recon for gound zero gzpw 21 spl
what song is this good sir?
Where from you get the music to the video??
how do you measure the spull at 8ohm or at 4 ohms?
You can use coil clock
What is a coil clock? I did a search on Google but it wasn't helpful. Is it some sort of measuring device?
@@bytraper I guess count the number of turns...
i think number of turn
@@emilalmberg1096 thanks, I didn't know what this meant
Super explain thank you sir
Sincerely thanks
Time to buy a new woofer.😂😂😂
You forgot to mention that for this technique to succeed, one must ensure that their fingers are as filthy as yours are here.
:-/ #Ecchhh
Hi Roger! How are you doing today?
Ill show you the cheapest and faster way!
what
Sam madel sir coil mm not matches... 2 cm round off side... bobi copper wiear mm???????
you place the displacement coil 5mm outwards
@@AlfredH not coil hite sir. Rounding copper wierkg mm?? Example fan coils winds number 36kg mm
sir
Eow sir..wat size of cuel that use of 15" speaker?
coil 100
A konsa licvid hai sar (black vala)
You don’t even label the products or at least put on screen what your using? What the heck man??….
where a buy coil?
Make em
What's the music name pls
I don't remember the name of the music
parda ki company ka name bta dian bhai
WHERE'S PART TWO???
sir ye glow ka naam kiya hai jo spekar par lagai hai
I do not understand
@@AlfredH he was asking about the glue you used in this video
lem apa ue wa? kaya tembelex ayam si?
Why copy đô che hai 360
Not too bad a result considering all your measurements were off by a factor of 10...
:-/
अरे भाई जब पुरा स्पीकर कोन फाड दीया है ! तो ५ रुपये का स्पायडर क्यो नही लगा रहे हों!. जले हुये स्पायडर मे क्यो उंगली कर रहे हो!
Alfred when and where p2 will start :)
सर आप यह पर देखो साफ कर रहे हो तो यह कौनसा लिक्विड है किसीसे एकदम अच्छा साफ हो जाता है
मैं उपयोग करता हूं: AXETON
Ano po pangalan ng padikit nyo po?
I make a video on this topic
AFF QUE GAMBIARRA ISSO
Thumbs down .
I hate these videos where there is no explanation . I guess they expect you to already know .
Going to find a video where someone knows what they're talking about.
Cómo se llama esa pieza que se cambió
No entiendo lo que quieres decir
Pedronolasco Sanhuezaalvarez
not
no by h ml do drop cool
En el vídeo se muestra como se cambia:,la bobina y el cono,,se hace una pequeña pestaña con cartón, lo más al ras de la bobina y la membrana,ya que la membrana es más grande y el pegamento podría adherirse a la canasta, se recomiendo utilizar pegamento epóxico para uso en membrana y bobina ya que es donde hay más fuerzas y pegamento amarillo (5000),pegamento de cola o de contacto para pegar hacia la canasta,como la membrana en parte externa,cono en la orilla de canasta Y las juntas que sujetan al cono
pardy kan name kia hy
what?
That was the most useless video I have ever watched. Was there a purpose that maybe was forgotten in the production?
Coil ko chipkaya hai
Wao
very bad working
Maybe you could have tried explaining what the hell you were doing instead of that awful annoying music.
8 inch spekar kaellai
yes
An
you
whats home niem fees book
phonic mx 300xe ka trasform jala hai to solusuon hai
Simple chiz ko itna complicate kr dala ......stolid
धन्यवाद
Just go buy new speakers why bother wasting time and a lot of it to source the parts if you can find who sells them anyway .
You talk to much
Please make your point clear