Hi! Great project! I have a question: Can we use more big syringes at the end to increase the force (since total area increases)? If we can, then would the syringe connections explode at heavier loads?
Yes you can increase upto a certain extent. The extent would depend upon the pressure rating of the weakest link in the set up. Before exploding I guess the syringe seal would give up and start leaking, therefore unable to lift the load. But it is possible that load would be lifted for some time and then the seal gives up causing a sudden fall of the load.
The steel ball acts as a ball valve, and prevents back-flow of fluid. 1. When the piston of the smaller syringe is pressed down, the ball does not allow the purple fluid to go back into the beaker in which the purple fluid is stored, and only allows it to go into the bigger syringe. 2. In the bigger syringe, it prevents the fluid from flowing back into the smaller syringe passively. Without the steel ball: 1. When the piston of smaller syringe is pressed, the fluid will go back into the beaker instead of the larger syringe because the small beaker offers a path of lesser resistance. This means that the larger syringe piston would never be pushed up. 2. If somehow, you were to able to push up the piston of lager syringe up, then the load on the larger syringe would cause the purple fluid to flow back into the smaller syringe. At that instanr , if the smaller syringe would not have the stell ball, the same fluid will flow back into the fluid beaker. But if the smaller syringe would happen to have the steel ball at that instant, it could create pressure at some point, probably causing the piston to get ejected out from the barrel of the small syringe, or some joint in the tubings would give away, and the purple fluid would spill over.
Paul Troiani I don't know? where to use it I think in the truck or car hahaha it show time to my friend and asking where did you learn that and my answer to my self hahahaha
Can you combine this project with your air compressor video and make a more advanced hydraulic system. You may take inspiration from the following videoHow It’s Made Hydraulic Cylinders
use gear motor with more troque and ver low revolutions. use car wiper moter for that. its best. use that motor to get reciprocating motion on the end of link to suck and pump fluid. jus like you did in your air pump
the world need creative people like you....good work!!
+Just A Clasher thnx
Thank you for the happiest year of my life😅🥵🥵🥵🥵😍😍😍😍😍😍
Tomorrow my science experiment This video is very helpful to me Thank you so much
This is awesome! Do you have a parts list where I could replicate this?
that was cool well done
Iïiibfh tu tu:ytgttttyyy8
I am totally makin this for my science exhibition
Hi! Great project!
I have a question: Can we use more big syringes at the end to increase the force (since total area increases)? If we can, then would the syringe connections explode at heavier loads?
Yes you can increase upto a certain extent. The extent would depend upon the pressure rating of the weakest link in the set up. Before exploding I guess the syringe seal would give up and start leaking, therefore unable to lift the load. But it is possible that load would be lifted for some time and then the seal gives up causing a sudden fall of the load.
Why have u used bearong ball is it very important to keep it in...
Plz reply waiting for ur reply plz
Varun arora I think the ball is meant to make it that the pressure can come in but can’t go out
Yo creo que es para hacer un sello del fluido osea para que de en un solo sentido el flujo.
Digo yo no sé.
Is it useful to civil engineers in any model making competion
DE CUANTO ES LA JERINGILLA MEDIDA POR FAVOR GRACIAS
What is the use of that ball bearing??can I make the model without using them ??
Pls reply
The steel ball acts as a ball valve, and prevents back-flow of fluid.
1. When the piston of the smaller syringe is pressed down, the ball does not allow the purple fluid to go back into the beaker in which the purple fluid is stored, and only allows it to go into the bigger syringe.
2. In the bigger syringe, it prevents the fluid from flowing back into the smaller syringe passively.
Without the steel ball:
1. When the piston of smaller syringe is pressed, the fluid will go back into the beaker instead of the larger syringe because the small beaker offers a path of lesser resistance. This means that the larger syringe piston would never be pushed up.
2. If somehow, you were to able to push up the piston of lager syringe up, then the load on the larger syringe would cause the purple fluid to flow back into the smaller syringe. At that instanr , if the smaller syringe would not have the stell ball, the same fluid will flow back into the fluid beaker. But if the smaller syringe would happen to have the steel ball at that instant, it could create pressure at some point, probably causing the piston to get ejected out from the barrel of the small syringe, or some joint in the tubings would give away, and the purple fluid would spill over.
Please what's the mechanical advantage and velocity ratio?
What size are the bearing balls? And where did you get the valve? I've been looking for the valve and haven't had any luck.
It is available in medical shops
Una pregunta la bolita pequeña como un balin es necesaria o para q sirve
tysm for ur live demonstration and assistance in my homeworkkkk😍
Maybe I’m missing something here, but why doesn’t the ball bearing stop the flow of the ink water when the syringe is decompressed?
WOW....ITS AMAZING EXPERIMENT...I WANT TO DO THIS PROJECT FOR MY COLLEGE FEST, PLEASE CAN I GET THE PROJECT REPORT OF THIS EXPT?????
your the best dude that's why I like your channel
+Riseof Herobrine thnx
And also I will sub you know
It's just awesome...now i will make this in my school project.👍
easy homemade project please tell me if we don't have wood than what we use
Good job dude, im going to try it with my kid.
Chillane ke liye kaun sa liquid use karenge
@@alokkushwaha4984Koi bhi incompressible liquid
wow.... Really superb one. keep it up. Love this idea.
Hello, how many lbs can its support?
Great job
Motorised hydraullick banana batayen plz...
Where can I find the valve?
Which glue u have used for fixing the pipes and syringes?
+Dhvani Shah hot glue
can you please show us your setup where you make videos
nice video
+Rohail Faisal thnx. Simple setup, no special tools used.
Easy HomeMade Projects : thanks for replying
can you please make a go kart
que mecanismos incrível parabéns
Hey from where did u buy this valve pipes..... Plz mention the link to buy it
Mysterious Manish you can buy these for cheap at pharmacy stores in India
Maheshwaran Paramasivan
Ok thanks for telling
This is very useful!
Paul Troiani I don't know? where to use it I think in the truck or car hahaha it show time to my friend and asking where did you learn that and my answer to my self hahahaha
Riseof Herobrine wood working projects where you need to glue pieces in very tight space
Ry
Will everything if I use a 20ml sryinge instead of a 60ml one
Materials required???
Thanks with regard to delivering many of these good info.
Please give some details of the project and materials
Nice project, make a electric version using the air compressor idea
sure
Can you combine this project with your air compressor video and make a more advanced hydraulic system. You may take inspiration from the following videoHow It’s Made Hydraulic Cylinders
how much weight did it will lift???
What is the ball bearing diameter in mm,please?
bro which adhesive u had used in it and which brand of syringe it is
plz rply soon bro
+rkuve singh i have used hot glue with simple syringes
Easy HomeMade Projects Hot glue? Means to warm the simple glue or that type of glue is available in the market??
Hey brother what if you combine the power of three big syringes how much will it lift?? Plz reply
What's the size of bearing balls?
Hello, From where can I buy such huge syringes and the valve
Please help where can I find a valve please respond
U can find it in any medical shop
@@umairanwar8520 thanks
So, can you make a bulldozer from syringes?
Or what is the ball bearing diameter in inch,please??
Good job guys.
please name me the glue used for joining the plastic materials like thi s(injections)
This is just hot glue !
what is this value and it name please tell me
Is that metal ball needed
what size of bearing , can i make it with bigger/smaller one?
I didn't understood that what is the role of bearing bolls
Boll bearing help to lock water
Is someone enjoying the asmr sounds
Waooooo😧😧.it's too good.🤗🤗
AMAZING!!!!!
what valve did you use
This is awesome
Where can I get the switch valve?
ما شا اللّه
بہت اچھا ویڈیو ہے
+Mian Tariq Ahmad شکریہ
I hate when people use just waaay too much hot glue, it gets me nervous for some reason
Raidzor つ ◕_◕ つ lol
Depende do material a ser usado. É vum otimo vedante e facil de remover
awesome work broo mashallah you are master
+HasnaiN BalocH thnx
Que se puede usar en vez de la bolsas de rodamiento?
use gear motor with more troque and ver low revolutions. use car wiper moter for that. its best. use that motor to get reciprocating motion on the end of link to suck and pump fluid. jus like you did in your air pump
What kind of valve is it?
From where you got that pipe
The little syringe
Bearing size please?
Great stuff right there bro💪💪👌. I got some projects for the kids
From where did u get the valve plz give me the link online
A desolder station ? Pompe vacum ?
Para qué es las pepitas o bolitas?
unbelievable
cool
welldone
+Abdul Rehman thnx
Awesome !
+Jean Papinou thnx
Easy HomeMade Projects if I don't use the bearing balls....will it work?....please ans me...
From where to get bearing balls
What's that wire thing with the pipe attached to it ?
which?
The tube at the beginning of the vid with the thing attached to it
erica c it's a medical drip set
TAHANK YOU
Good job sir
Sir what is the size of the big syringe?
Thanksfor the hydrolicense
Hey bro , ' love' you for this video !!
+王雷 thnx
u are so creative
what can i use to seal those leaks? theyre everywhere
Also what's the purpose of this plz answer with details
I reccomend a motor for the pump.
Thanks alot❤️💯
y u preferred ink water any reason behind that.
+Surya Prasad only to make it visible in camera.
How do we make this system with electric motor
Да?А я думал что вы вообще руками поднимайте тяжести
Umut Değirmenciler
You make a water pump
hi
Umut Değirmenciler
bro nila water h ya kuch or
+Neeraj Kumar water
what are the steel balls for
what is ink water? does this have to be ink water? will normal water work?
How many syringe We need ? ? Can u Plz tell Me. . It's urgent
Where can we buy the bearing balls?
What is Ink water
I like all your projects jajaj
+Giuseppe De Lilla thnx
what ml syringe did u use
Good job
Anyone know the dimensions of the syringes?
Where do you come up with this stuff? Love it keep it up
+league thnx
Brother I want Yr Help,
+Umar najam contact me on my Facebook page. Link is in description
Thank you...
How a car brake system works , just think about pupping your brakes :)
how to make a forklift in hydraulic plz show sir am waiting