I hit this exact situation during an electronics lab session in college. Took two of us over an hour to sort out why we were seeing microvolt signals on the scope while the LED on our logic probe was lighting up. We changed out everything in the circuit and were at the point of swapping out the scope when the probe cable sheared off leaving only the connector on the scope. Absolutely infuriating BUT provided a lifelong lesson to never trust cables and connectors, especially those that are constantly beat up in a electronics lab classroom.
Happens to the best of us. Should probably try to get in the habit of probing the calibration point on the front of the scope occasionally. It'll be interesting to see the difference with the HDMI job.
I got into this habit in my first job and it's saved me a ton of time over the years and meant I can trust what I'm seeing just a little bit more. Nicely pointed out by the way!!
asolutely - it's not like I didn't know or wasn't taught to do these things - just sometimes standards slip due to over-familiarity and the fact that almost always the scope/meter whatever probe is fine
@@gdj6298 not necessarily as you'll see a ton of noise on the scope, this is down to the electron propagation needing a return path which is as close as possible to the signal wire. You can try this yourself by grounding the ground lead and removing it whilst looking at the scope. Once you get used to the difference you'll notice of there's a missing ground straight away, it's really down to years of experience and checking three times. I didn't realise this when learning all those years ago and wasn't really told why. It's definitely a good thing to question everything all the time though, as you'll make less mistakes and learn a lot. Have fun electronicing!!
Been there, done that! No flag from my side! I’ve experienced more bad probes than I can count. At some point they break, especially if you misuse them mechanically or in a climate chamber… I like to have a 1.5 V battery handy to check my scope or voltmeter. P.S. Keep the wire and BNC connector of the dead probes! It’s a special kind of lossy coax and quite hard or even impossible to come by.
That's what the 5v square wave test point is for on the scope "most scopes have one". I used to tell my students to always test that first , (also this test point is their to calibrate the probs "little preset on the probe").
I had a similar issue with my Rigol o'scope about six months ago (same model as in this vid), I wasn't getting proper readings with it. Turned out the stupid end piece of the probe was loose, and had a tiny gap between the two parts. lol
@@andymouse I found a neat use for the 1 KHz test output on the o'scopes, btw... A couple of years ago, I needed to reverse engineer the pinout of an FPGA vs the other chips (RAM etc.) on a board. Originally, I was going to just use a counter on the FPGA to output a bit to each pin, then use the frequency to figure out which pin was used. But that could cause possible contention. So instead, I just added ALL the pins to a SignalTap instance, and set them all as inputs. Then used a resistor from the o'scope's 1 KHz test output to probe each trace. There was a small amount of crosstalk on adjacent traces, but it was still obvious which pin was the correct one. I managed to reverse about 95% of the pin mapping that way. I don't own a proper signal gen. lol
@@electronash Nice application and good thinking ! that would be a good video for someone to make, highlighting odd ways to use the 1Khz cal output !! cheers!
Ive got semi-related experience: Im working in test development, so i'm developing/maintaining testequipment for our products. Basically I build adapters that connect testequipment (multimeters, sources, loads etc.) to the devices under test (ranges from simple pcbs to multi-pcb modules to full devices). Maintaining in my case means, everytime there is a problem with my adapter, someone calls me to fix it. 95% of the time its the cables. Either shorted inside, or the soldered connection broke off, the crimping got old, someone plugged it in the wrong way... there is a surprising amount of ways a cable/connection can be the reason for a fault. So if youre ever working on some elaborate setup and its giving surprising results: Check your cables. Especially if you frequently (un)plug them.
Richard we all been down that road, I had a jinky feeling it may of been your test lead, but you got into it great, cheers bud keep up the great work mate 🤙🏼🇦🇺
I always learn from your mistakes. Thanks to your previous two HDMI videos, these connectors are less of a mystery. I appreciate the in depth explanations and the demonstration of using an oscilloscope (for HDMI and the AM/FM radio repair). I also like the 1hr+ videos and don’t mind the multimeter continuity beeps lol.
Thank you. Most of the info I publish is already 'out there' It's just sometimes hard to access and even harder to put together in a coherent way from the point of view of trying to fix stuff. I can't guarantee that learning this stuff will enable you to repair HDMI problems all the time but I can guarantee it will give you a logical method to go about it 😉
Well worth sharing as a reminder. Does your scope come with a little function generator point on the front as a sanity check? Is that the quickest way to check you are good to go?
Good point. I was using my Peak semiconductor tester to test a voltage regulator that may or may not have been bad. The tester told me that there was no component present. Checking the manual showed that it can only check VR's up to 8 volts! It's a great test tool, but I was using it incorrectly. Testing that same component with my multimeter proved that it was still ok.
Brilliant! Thanks for sharing the fail, very important to show this kind of gotcha! I use the test signal point on my scope to "calibrate" before probing,,, too many times done the 1x/x10 mixup and the AC/DC coupling..Cheers!
Thank you for the great reminder! I have made these kinds of mistake and worse and will again, I'm sure, so thank you. Maybe your reminder will help me NOT make some mistakes I would have made, if you hadn't made me more careful.
Just went through testing a ton of components on an RCA VoltOhmyst WV-500B I picked up on ebay because non of the ranges were working consistently. Turns out the integral probe cable has an intermittent fault at the strain relief going into the meter. Trimmed it back and ready for calibration now. Bit of a D'oh moment.
Absolutely agree with this! I've has this exact issue with a Tektronix scope and Tektronix probes not long ago, spurious readings taking me up the garden path. These have a small connection that connects to the BNC part and it was not fully inserted... Another major issue is with RF/Coax patch leads. I've lost count of how many times I've been trying to repair or align a transceiver had had spurious power readings, high SWR and desensitised front ends. All because of an rf cable. I only buy high quality interconnects and coax cable now. And one important advice I can give anyone. If you're working with a HV/EHT probe, check at least 3 times you have the ground lead connected!!!
Seeing as a HV/EHT probe is basically a voltage divider it would make sense to ensure one end of the resistor chain is connected to ground! Unless you want to become part of the voltage divider yourself😆
@@LearnElectronicsRepair Yes exactly😀that's why I said check 3 times. I have had the ground pop off while I was measuring the EHT on a CRT, that gave me a fright 😂
lol,, had a problem with my fluke multimeter... new leads and readings all over the place... ended up cutting off the insulation and the tips were not even soldered to the wires. just crimped and a bad crimp at that... messed with me for hours.
It happen to me also with multimeter probes. But has the multimeter was new i try to activate the warranty. But they said that kind of material is like a consumable and not covered by warranty. I was young then and accepted.
So, you were able to connect the ground probe of your ‘scope directly to the ground of your DC supply because both units are connected to mains through an isolation transformer? Is that right?
weve all done this at some stage... trust nothing until tested at the start of a fault find.. when i was on a mine site i tested my multimeter religiously with a never touched 12v 6.5Ah alarm system battery which had one purpose only, to check the multimeter for 12vdc accuracy. many years ago electronics out of the box, brand spanking new you could trust as being perfect 99.99% of the time... then it seems, at least in the electronic security area, you would get components faulty from the factory, around 1%. then it went to 20% in 2001 or so... a sad statement on quality control worldwide..
I bought a Rigol DS1202EZ brand new, spoiling myself and replacing my old 70's analogue scope. Quite quickly I found that one of the probes was faulty and gave weird intermittent readings. Rigol replaced it no quibbles but I wonder if the standard probes can be a bit of a weak point as the scope is brilliant? May I ask a quick question? I'm relatively new to this level of electronics and wondered what is considered the highest voltage it is safe to put into my oscilloscope before I'd need to use differential probes. I've been very careful with grounds and voltages but it would be nice to know. Thanks.
The point of using differential probe is not so much to do with the maximum voltage as it is to do with where you can and can not connect the ground lead of your scope 😉
There are so many to choose from and a lot depends on budget as well. More will depend on who you ask! Probably any auto ranging multi meter with a fast responding 'bleeper' on the continuity range will be good enough for your use, of the three I use regularly I like all of them. The Aneng AN8008 is very nice to use and has good resolution (down to 1mV on the millivolts range, it has a microamps range I find very useful and reads resistance to 0.01 ohms. I would say it is the best all rounder of the meters I own and the highest resolution 1.999 digits. The Kaiweets DM601 has the nicest display and the fastest short/continuity indication of three. But my old Fluke 79 which I have had for years is the best in diode test mode as it gives one short bleep for semiconductor junctions and a continuous bleep for shorts - non of the other two do that and it is very useful for fault finding, but it has the lowest resolution of the three on ohms or millivolts (reads to 0.1 ohms). A second hand Fluke is a good choice, I've had mine since 1993 (new) and it's still working well. There is a newer version of the Aneng, called AN8009, which I haven't used but it looks to be very similar to An8008. Also there is the AN870 which looks very interesting and adds an extra digit of resolution again - so 1.9999V rather than 1.999V and is very well priced for this feature and comes well recommended by others. I haven't tried one yet myself though i will soon I'm waiting for a review sample AN870 from Banggood but the first one got lost in the post and the second one is stuck in customs somewhere at the moment
@@LearnElectronicsRepair Thank you for your detailed response. I was thinking about AN8008, going to check for another ones you mentioned. Have a good day
Another effect of applying three tons of sideways pressure to the probe tip, similar to what happens with DVM probes. Ho, ho. Everybody drops a clanger know and then, as long as you learn from them then that is fine. I once shorted a piece of live chassis equipment, and did a lot of damage, when using a grounded scope. Your misdemeanours are mild in comparison.
This is a good lesson to learn actually, I wonder if there is a way to force your self to calibrate the probes every so often, like written into the scope its self, or just modify the scope to have something that monitors the last time the calibration button was pressed and then display it on a little display.
Test your tester , dash diving = working upside down looking for power under the dashboard of a car , could not find power , after a while I figured out the bulb was broken in the testlight ;)
OMG... If I had a dollar for every bad ROC DMM probe I'd be a millionaire! I switched ALL of my probes and leads to Probe Master.. They're worth every penny in saved time and second guessing yourself... I've also gotten into the habit of testing my DMM after any high voltage work.. Bad fuses will also give you fits..
I've been a professional service engineer for over 35 years and a hobbyist for well over 40 years, and I've NEVER done anything like that, EVER. I've never let the magic smoke out, never tried to measure voltages on something that isn't powered up, never connected a power supply the wrong way round, never inserted an electrolytic or tant the wrong way round, or any semiconductors whatsoever. 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥 🩲 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥
same mistake and whit polymer probes... No work no good voltage no signal whay led its on i dont have voltage... Of course broken probes 80 minutes wasted times..... Stunit things (sorry for that) .... And olways forgot to test probes or broke in the job and dont anterstent... This another story....
good grief. what are you gonna do? test all your leads and probes every day? it's gotta happen. we've all spent countless hours because of bad wires. so many times i've rewired some guitar pickups and stuff, and the guitar cable decided to go wonky in the middle of it. waste's so much time.
It's a reminder that you should test your leads when you use them - in the same way I always test my probes by touching them together before taking continuity readings, I should touch your scope probe to the little calibration point you find on just about any scope. I usually just touch the end of the scope probe against my finger to see if I get 'mains hum' on the trace and if I do I assume it is good. This time it came along and bit me on the bum.
I hit this exact situation during an electronics lab session in college. Took two of us over an hour to sort out why we were seeing microvolt signals on the scope while the LED on our logic probe was lighting up. We changed out everything in the circuit and were at the point of swapping out the scope when the probe cable sheared off leaving only the connector on the scope. Absolutely infuriating BUT provided a lifelong lesson to never trust cables and connectors, especially those that are constantly beat up in a electronics lab classroom.
Happens to the best of us. Should probably try to get in the habit of probing the calibration point on the front of the scope occasionally. It'll be interesting to see the difference with the HDMI job.
I got into this habit in my first job and it's saved me a ton of time over the years and meant I can trust what I'm seeing just a little bit more. Nicely pointed out by the way!!
asolutely - it's not like I didn't know or wasn't taught to do these things - just sometimes standards slip due to over-familiarity and the fact that almost always the scope/meter whatever probe is fine
guys, i would rather trust a battery to test from, its isolated from bad AC input.. or the multimeter might be at fault as well.
But if the problem is in the GROUND connection to the probe - won't the calibration point still read good, if it's grounded internally ?
@@gdj6298 not necessarily as you'll see a ton of noise on the scope, this is down to the electron propagation needing a return path which is as close as possible to the signal wire. You can try this yourself by grounding the ground lead and removing it whilst looking at the scope. Once you get used to the difference you'll notice of there's a missing ground straight away, it's really down to years of experience and checking three times. I didn't realise this when learning all those years ago and wasn't really told why. It's definitely a good thing to question everything all the time though, as you'll make less mistakes and learn a lot. Have fun electronicing!!
No chastising needed, just plenty of praise for your scientific honesty!
Been there, done that! No flag from my side!
I’ve experienced more bad probes than I can count. At some point they break, especially if you misuse them mechanically or in a climate chamber… I like to have a 1.5 V battery handy to check my scope or voltmeter.
P.S. Keep the wire and BNC connector of the dead probes! It’s a special kind of lossy coax and quite hard or even impossible to come by.
That's what the 5v square wave test point is for on the scope "most scopes have one". I used to tell my students to always test that first , (also this test point is their to calibrate the probs "little preset on the probe").
Nice one ! I always tap the ' calibration ' output on the scope with my probe as a sanity check !.....cheers.
Hey, I was gonna say that!
Allo, Andy. lol
I had a similar issue with my Rigol o'scope about six months ago (same model as in this vid), I wasn't getting proper readings with it.
Turned out the stupid end piece of the probe was loose, and had a tiny gap between the two parts. lol
@@electronash Watcha !
@@andymouse I found a neat use for the 1 KHz test output on the o'scopes, btw...
A couple of years ago, I needed to reverse engineer the pinout of an FPGA vs the other chips (RAM etc.) on a board.
Originally, I was going to just use a counter on the FPGA to output a bit to each pin, then use the frequency to figure out which pin was used.
But that could cause possible contention.
So instead, I just added ALL the pins to a SignalTap instance, and set them all as inputs.
Then used a resistor from the o'scope's 1 KHz test output to probe each trace. There was a small amount of crosstalk on adjacent traces, but it was still obvious which pin was the correct one.
I managed to reverse about 95% of the pin mapping that way. I don't own a proper signal gen. lol
@@electronash Nice application and good thinking ! that would be a good video for someone to make, highlighting odd ways to use the 1Khz cal output !! cheers!
Ive got semi-related experience:
Im working in test development, so i'm developing/maintaining testequipment for our products. Basically I build adapters that connect testequipment (multimeters, sources, loads etc.) to the devices under test (ranges from simple pcbs to multi-pcb modules to full devices).
Maintaining in my case means, everytime there is a problem with my adapter, someone calls me to fix it. 95% of the time its the cables. Either shorted inside, or the soldered connection broke off, the crimping got old, someone plugged it in the wrong way... there is a surprising amount of ways a cable/connection can be the reason for a fault.
So if youre ever working on some elaborate setup and its giving surprising results: Check your cables. Especially if you frequently (un)plug them.
Richard we all been down that road, I had a jinky feeling it may of been your test lead, but you got into it great, cheers bud keep up the great work mate 🤙🏼🇦🇺
If you’re not making mistakes it’s because you’ve never done anything.
very true 😉
Yep, there was only one dude who never made mistakes, and we crucified that guy.
(Said as a joke, not a religious statement)
@@bosborn1 oh snap, that’s a good one though. Love the humor
Knowledge from a mistake is not easily forgotten. Thanks for sharing.
Humility... So refreshing these days.
I always learn from your mistakes. Thanks to your previous two HDMI videos, these connectors are less of a mystery. I appreciate the in depth explanations and the demonstration of using an oscilloscope (for HDMI and the AM/FM radio repair). I also like the 1hr+ videos and don’t mind the multimeter continuity beeps lol.
Thank you. Most of the info I publish is already 'out there' It's just sometimes hard to access and even harder to put together in a coherent way from the point of view of trying to fix stuff. I can't guarantee that learning this stuff will enable you to repair HDMI problems all the time but I can guarantee it will give you a logical method to go about it 😉
Classic. Been there - several times.
Looking forward to a review on the HDMI problem tracing 👍
Well worth sharing as a reminder. Does your scope come with a little function generator point on the front as a sanity check? Is that the quickest way to check you are good to go?
Yes it has a square wave 'calibration' generator - I should remember to use it!
Good point. I was using my Peak semiconductor tester to test a voltage regulator that may or may not have been bad. The tester told me that there was no component present. Checking the manual showed that it can only check VR's up to 8 volts! It's a great test tool, but I was using it incorrectly. Testing that same component with my multimeter proved that it was still ok.
Brilliant! Thanks for sharing the fail, very important to show this kind of gotcha! I use the test signal point on my scope to "calibrate" before probing,,, too many times done the 1x/x10 mixup and the AC/DC coupling..Cheers!
Thank you for the great reminder! I have made these kinds of mistake and worse and will again, I'm sure, so thank you. Maybe your reminder will help me NOT make some mistakes I would have made, if you hadn't made me more careful.
Just went through testing a ton of components on an RCA VoltOhmyst WV-500B I picked up on ebay because non of the ranges were working consistently. Turns out the integral probe cable has an intermittent fault at the strain relief going into the meter. Trimmed it back and ready for calibration now. Bit of a D'oh moment.
Absolutely agree with this! I've has this exact issue with a Tektronix scope and Tektronix probes not long ago, spurious readings taking me up the garden path. These have a small connection that connects to the BNC part and it was not fully inserted... Another major issue is with RF/Coax patch leads. I've lost count of how many times I've been trying to repair or align a transceiver had had spurious power readings, high SWR and desensitised front ends. All because of an rf cable. I only buy high quality interconnects and coax cable now.
And one important advice I can give anyone. If you're working with a HV/EHT probe, check at least 3 times you have the ground lead connected!!!
Seeing as a HV/EHT probe is basically a voltage divider it would make sense to ensure one end of the resistor chain is connected to ground! Unless you want to become part of the voltage divider yourself😆
@@LearnElectronicsRepair Yes exactly😀that's why I said check 3 times. I have had the ground pop off while I was measuring the EHT on a CRT, that gave me a fright 😂
Very good. Something lots of people have done. Including myself. Cheers.
lol,, had a problem with my fluke multimeter... new leads and readings all over the place...
ended up cutting off the insulation and the tips were not even soldered to the wires.
just crimped and a bad crimp at that... messed with me for hours.
Thats why I always use the scope's 1V @ 1KHZ Calibration signal output to verify the probe & scope.
It happen to me also with multimeter probes. But has the multimeter was new i try to activate the warranty. But they said that kind of material is like a consumable and not covered by warranty. I was young then and accepted.
Ouch! Been there, done that too. So frustrating.
Yep found that in automotive testing. Don’t assume the tools are good ever
Excellent that you found the fault and realised that it was the tool, also credit to you, that you told every body. Full 5***** DG
Well if there is one thing this channel is, it is real 😁
I learned a lot about camera shake and seizure inducing strobing. That is, to avoid videos with those visually toxic features.
So, you were able to connect the ground probe of your ‘scope directly to the ground of your DC supply because both units are connected to mains through an isolation transformer? Is that right?
weve all done this at some stage... trust nothing until tested at the start of a fault find.. when i was on a mine site i tested my multimeter religiously with a never touched 12v 6.5Ah alarm system battery which had one purpose only, to check the multimeter for 12vdc accuracy. many years ago electronics out of the box, brand spanking new you could trust as being perfect 99.99% of the time... then it seems, at least in the electronic security area, you would get components faulty from the factory, around 1%. then it went to 20% in 2001 or so... a sad statement on quality control worldwide..
I bought a Rigol DS1202EZ brand new, spoiling myself and replacing my old 70's analogue scope. Quite quickly I found that one of the probes was faulty and gave weird intermittent readings. Rigol replaced it no quibbles but I wonder if the standard probes can be a bit of a weak point as the scope is brilliant?
May I ask a quick question? I'm relatively new to this level of electronics and wondered what is considered the highest voltage it is safe to put into my oscilloscope before I'd need to use differential probes. I've been very careful with grounds and voltages but it would be nice to know.
Thanks.
It is common on Rigol probes for the ground lead to fail.
The point of using differential probe is not so much to do with the maximum voltage as it is to do with where you can and can not connect the ground lead of your scope 😉
Evey scope that I have ever seen has a 5 volt DC square wave output terminal for calibrating your probes. I always check before I measure.
Can you recommend a multimeter for a electronic beginner hobbyist. ?
There are so many to choose from and a lot depends on budget as well. More will depend on who you ask!
Probably any auto ranging multi meter with a fast responding 'bleeper' on the continuity range will be good enough for your use, of the three I use regularly I like all of them.
The Aneng AN8008 is very nice to use and has good resolution (down to 1mV on the millivolts range, it has a microamps range I find very useful and reads resistance to 0.01 ohms. I would say it is the best all rounder of the meters I own and the highest resolution 1.999 digits.
The Kaiweets DM601 has the nicest display and the fastest short/continuity indication of three.
But my old Fluke 79 which I have had for years is the best in diode test mode as it gives one short bleep for semiconductor junctions and a continuous bleep for shorts - non of the other two do that and it is very useful for fault finding, but it has the lowest resolution of the three on ohms or millivolts (reads to 0.1 ohms). A second hand Fluke is a good choice, I've had mine since 1993 (new) and it's still working well.
There is a newer version of the Aneng, called AN8009, which I haven't used but it looks to be very similar to An8008. Also there is the AN870 which looks very interesting and adds an extra digit of resolution again - so 1.9999V rather than 1.999V and is very well priced for this feature and comes well recommended by others. I haven't tried one yet myself though i will soon
I'm waiting for a review sample AN870 from Banggood but the first one got lost in the post and the second one is stuck in customs somewhere at the moment
@@LearnElectronicsRepair Thank you for your detailed response. I was thinking about AN8008, going to check for another ones you mentioned. Have a good day
@@tttttttt8482 You will be more than happy with the AN8008 I Am sure
Hi do you have a video on how to us an oscilloscope?
Muy buen canal de reparación de bricolaje, tenemos que contactarlo.
Another effect of applying three tons of sideways pressure to the probe tip, similar to what happens with DVM probes. Ho, ho. Everybody drops a clanger know and then, as long as you learn from them then that is fine. I once shorted a piece of live chassis equipment, and did a lot of damage, when using a grounded scope. Your misdemeanours are mild in comparison.
Always useful to remember this
This is a good lesson to learn actually, I wonder if there is a way to force your self to calibrate the probes every so often, like written into the scope its self, or just modify the scope to have something that monitors the last time the calibration button was pressed and then display it on a little display.
Excellent update.
Thank you for sharing :)
My first Boss once told me the bloke that never makes a mistake never does anything.
Too late. 😁 Been there. Done it.
Thank you for your amazing lessons.
What’s the difference between
Tmmbat42 and Tmmbat42film. Can I use film instead of tmmbat42
Thanks for tip
Test your tester , dash diving = working upside down looking for power under the dashboard of a car , could not find power , after a while I figured out the bulb was broken in the testlight ;)
Great advice!
Very neat board 👌 👍 but do you need suitcase or backpack for the battery's 🤣😂
I often check my probe before using it. That way I know its working before taking a measurement.
OMG... If I had a dollar for every bad ROC DMM probe I'd be a millionaire! I switched ALL of my probes and leads to Probe Master.. They're worth every penny in saved time and second guessing yourself... I've also gotten into the habit of testing my DMM after any high voltage work.. Bad fuses will also give you fits..
You're a legend
Had a similar thing with a multimeter. Turns out the battery was just low lol.
This means that we'll get a conclusion for the HDMI stuff :)
This did not show up when you compensated the probe, being that the probe was dropping the voltage same as a resistor.
I wonder if the 1x/10x switch has gone a bit dodgy? It wasn't exactly 1/10th the reading.. but close. Try it in 10x maybe?
I would but it's in the bin now - I have 5 or 6 others 😁
@@LearnElectronicsRepair Ah well, best place for it really! 😄
That's always fun.
No stupid mistake here Richard, think it must have happened to all of us at one point or another.
True but you still feel pretty dumb when you do it again 🙄
Wow, ur a human. For a moment there I thought u are a robot or cyborg.
Humans make mistakes. No big deal.
I always test for DC voltages with my meter.. (Fluke of course!)
The same advice extends to Multimeters (Fluke or otherwise), test leads and anything else you use in fault finding.
@@LearnElectronicsRepair The road to perfection is paved by many mistakes!
great tip! (no pun intended)
Doh! Measure twice, cut once.
School Boy error, NO treat's for you this week laddie.
I thought you were going to sayit was a probe with a built in attenuator
I've been a professional service engineer for over 35 years and a hobbyist for well over 40 years, and I've NEVER done anything like that, EVER.
I've never let the magic smoke out, never tried to measure voltages on something that isn't powered up, never connected a power supply the wrong way round, never inserted an electrolytic or tant the wrong way round, or any semiconductors whatsoever.
🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥 🩲 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥
Or tried to measure voltage with your multimeter (leads and all) set to AMPS! 😆
You haven't been doing it properly 😂
Ya, he has NEVER EVER done it properly 😄
As long as you can laugh about yourself, all is OK. Or: You are only stupid if you can't find the error (and don't ask for help).
So I told my wife that I need to first test it before I use it she was not amused
We all make mistakes.. lol 😆 ..
I need help I posted a comment on one off your videos could you please respond?
Which video?
@@LearnElectronicsRepair LER #036 - Circuits & Components for Beginners 5. Learn About Capacitors, Bad, Faulty, How They Fail
same mistake and whit polymer probes... No work no good voltage no signal whay led its on i dont have voltage... Of course broken probes 80 minutes wasted times..... Stunit things (sorry for that) .... And olways forgot to test probes or broke in the job and dont anterstent... This another story....
good grief. what are you gonna do? test all your leads and probes every day? it's gotta happen. we've all spent countless hours because of bad wires. so many times i've rewired some guitar pickups and stuff, and the guitar cable decided to go wonky in the middle of it. waste's so much time.
It's a reminder that you should test your leads when you use them - in the same way I always test my probes by touching them together before taking continuity readings, I should touch your scope probe to the little calibration point you find on just about any scope. I usually just touch the end of the scope probe against my finger to see if I get 'mains hum' on the trace and if I do I assume it is good. This time it came along and bit me on the bum.
You Got Spam comment..😂
Yeah always happens in the first 30 mins after publishing - I deleted them now.
Id like my 8 minutes back
I'll see what I can do 😁
Whats with the yuuus ! cannot listen to that yuuuu yu know yuuuu
😆😆😆😆😆