Good video. I have a Emerson Digital Controller , It shows me on the screen p2, the problem is that the evaporator is leaking of ice, it does not do the defrost cycle. You can help. Electric Heater is good 👍
The "locking" effect comes from the door making an airtight seal around the perimeter of the door. When you open the door, you let in a blast of warm air, and let out a blast of cold air. When you close the door, the warm air begins to cool. Cold air has a lower pressure than warm air, creating a suction effect that makes it very difficult to open until the pressure equalizes. That your freezer does this is a sign that your gasket is in good condition, and is working properly.
The one your looking for is LS and US possibly just use SET if yours is already mostly set up. Unlike mine many others used before I got to it so all the values are changed and I can't find any source or info about the default values. I know how to change just don't know the rec settings/ factory settings.
hola buenas tardes saludos para todos los colegas espero se encuentren bien les quería pedir el favor de ayudarme con tutorial en español del manejo de los parámetros de dixell xr60cx
My prep cooler was messed up! I decided to put everything back to factory default settings. When I did, P2 error started. So, in programming mode I changed my P2 parameter setting back to N instead of Y and the error stopped. My cooler’s manual is worthless. I had better luck looking at this manual for the controller: masterfrigo.com/wp-content/uploads/2013/10/XR06CX_GB.pdf
For a company as big as HK International this video is an embarrassment. It tells you absolutely nothing. It was published over 4 years ago and not a single response from the publishers to any of the significant questions raised by the audience who have clearly come here looking for answers that they didn't find. Word to HK. If you are going to engage in social media then at least make an effort to give the job to someone who is competent enough to do so. Whoever produced this crap is clueless not only about engaging with the general public through social media but also at the product level. Once the unit is installed it should be obvious to anyone who has been through that process what the next step is likely to be: set the preferred working temperature. That's what this video should present in a stepwise fashion. Not some general discussion about how to change the many and varied parameters most of which are vague at best as to what they represent. Must do better.
This answer represents the feelings of many people going through the same frustration. There's zero information here on how to actually set anything up.
Abbreviations
LS = Minimum setpoint
US = Maximum setpoint
Is the minimum for the highest hot point and the maximum for the lowest cold point?
Not logical @@Jordan-gt8ht
Where is the parameter list?
Good video. I have a Emerson Digital Controller , It shows me on the screen p2, the problem is that the evaporator is leaking of ice, it does not do the defrost cycle. You can help.
Electric Heater is good 👍
How do you put unit in manual defrost, to check this circuit?
Hi. I follow the steps but it’s still not the temperature that I want. Help please. Thanks
Anyway to set it from locking? Door locks for a few seconds after we open the door each time.
The "locking" effect comes from the door making an airtight seal around the perimeter of the door. When you open the door, you let in a blast of warm air, and let out a blast of cold air. When you close the door, the warm air begins to cool. Cold air has a lower pressure than warm air, creating a suction effect that makes it very difficult to open until the pressure equalizes. That your freezer does this is a sign that your gasket is in good condition, and is working properly.
Hk International I do exactly like you but the temperature still 35 ° do you know what can I do more ?
This doesn't tell me how to make it the temperature I want and the instruction manual doesn't either.
The one your looking for is LS and US possibly just use SET if yours is already mostly set up.
Unlike mine many others used before I got to it so all the values are changed and I can't find any source or info about the default values. I know how to change just don't know the rec settings/ factory settings.
@@daweicunningham6819the defaults are stored on internal memory and you can reset back to them. It’s in the manual somewhere how to do it.
Hi I am able to enter the program mode before but now when I hold the set and arrow down button for 5 sec it displays pof. What I am doing wrong?
what is EA error in dixell XR06CX controller, PLEASE reply at the earliest
hi mahesh have u found a fix for that issue? i have problem EA blinking too
Our temperature -20 degree.show multifreezer combine unit and full wiring and settings and symbols.
It goes back to 25 degress once i set why?
What is EA ( letters flashing )error in dixell XR06CX controller, can anyone help n explain it to me at the earliest please. Thanks.
How do I set the defrost on this unit
I want yonjlw to reset or setting for table top cold show case for cake n pastry van u help me out of this its geeting more cold
is there a factory reset parameter????
why don`t they make it easy like traditional thermostat? why the fuk make it so complicated ?
How do I shut off low Temperture alarm .? MBF8501
Is there audio on this video?
Defrosting time?
Wuts does P2 code mean
How is it possible a $5000 piece of equipment has such a lousy instruction manual? It doesn't tell you what any of the abbreviations stand for.
What is P2
what does the abbreviations stand for
What abbreviation do you have in mind?
What is HE error
ซื้อได้ที่ไหนครับ
thanks for a good video
Just tell us how to raise the temperature so all of my drinks dont fucking freeze
Pi coming what problem??!
hola buenas tardes saludos para todos los colegas espero se encuentren bien les quería pedir el favor de ayudarme con tutorial en español del manejo de los parámetros de dixell xr60cx
இந்த டெம்பரேச்சர் ரீடிங் சரி செய்வதற்கு தமிழில் பதிவு போடவும்
What does P2 error mean
My prep cooler was messed up! I decided to put everything back to factory default settings. When I did, P2 error started. So, in programming mode I changed my P2 parameter setting back to N instead of Y and the error stopped. My cooler’s manual is worthless. I had better luck looking at this manual for the controller:
masterfrigo.com/wp-content/uploads/2013/10/XR06CX_GB.pdf
@@andykistner2240 Thanks for the info. Was able to change Dwell From factory setting of 7 to 5.
What is HT
Thank you, that is very helpful.
WHY COMING P2 please answer me
Well done keep it up for message
For a company as big as HK International this video is an embarrassment. It tells you absolutely nothing. It was published over 4 years ago and not a single response from the publishers to any of the significant questions raised by the audience who have clearly come here looking for answers that they didn't find. Word to HK. If you are going to engage in social media then at least make an effort to give the job to someone who is competent enough to do so. Whoever produced this crap is clueless not only about engaging with the general public through social media but also at the product level. Once the unit is installed it should be obvious to anyone who has been through that process what the next step is likely to be: set the preferred working temperature. That's what this video should present in a stepwise fashion. Not some general discussion about how to change the many and varied parameters most of which are vague at best as to what they represent. Must do better.
This answer represents the feelings of many people going through the same frustration. There's zero information here on how to actually set anything up.
Character In the video It's great, I like it a lot $$
heloo how to adjust difference in on and off comprssor...
What do i have to do to go back as factory
plz uplode blast freezer progaramig
What is the meaning _d_
What does PF code meaning, when I am trying to hold Set botton.
Please call our Warranty Department for technical support at 1-800-877-7782 (opt 6) or email warrantydept@hki.com
Thank you
Thanks bro
Super
Just love silent movies. Verbal explanations would be they thing , don't you think?
Q o w
Hy?
Hi
Saya tidak percaya ia boleh menjadi sebaik ini
⁉️
Sir, H2 alarm showed, how to solve?