Tuning a dual resonant system creating high voltage and current that are in phase.
HTML-код
- Опубликовано: 1 июн 2024
- Two capacitive coupled resonant systems are tuned,
producing high voltage and current that are in phase.
The high voltage creates strong displacement currents
that power the high current system.
This is a form of dielectric induction.
If you want to support my research,
you can make a donation on my PayPal:
www.paypal.com/donate/?hosted...
Thank you for your support!
Chapters:
00:00 - intro
02:08 - pancake coils instead of solenoid coil
02:39 - introduction to the experiment
03:10 - setup
10:08 - The PCB with flow chart
12:39 - The probes
13:27 - The current probe fault
17:20 - First experiment
19:24 - Detuning up and down
22:42 - Q factor
23:19 - detuning with less parallel capacity
26:28 - it looks tuned but isnt!
26:55 - tuning the HV system
27:19 - less paper=more capacity=lower frequency
29:14 - back to 15mm paper, checking the hV Fres
30:23 - max input power giving 38A 3kV in phase
32:09 - Infrared measurement
34:37 - Intro to experiment 2
34:46 - The square wave schematic
34:52 - the boost coil
36:25 - square wave on the scope
38:08 - changing the square wave phase
40:43 - Measuring with LCR meter
41:23 - 31.33 uH unloaded
41:37 - 8.13 uH shorted
42:28 - measuring the capacitance
42:51 - measuring the parallel capacity
43:19 - Conclusion
43:27 - Next up
43:53 - scrolling instructions
Great work! Nikola would be proud of you
The first tesla coil I built, I used copy paper as a capacitor as well. I took aluminum foil, and layed it in laminating film and laminated it as the 2 plates. And then used paper to fine tune the capacitance of the system. It is a super simple and cheap method of making capacitors. Good work on the setup you have. I like the pcb you built. Keep up the great work
thanks !
@@MasterIvo have you considered that resonance is also a quality of sound? When I was experimenting with tuning forks I noticed that a tuning fork will resonate with a frequency that matches its tuning, or any multiple thereof.
Would you consider experimenting with your system to see if multiples of the primary coil would resonate with the secondary? I am interested in the potential results, unfortunately, I don't have a system as articulate as your system is.
Please keep doing this work 🙏 our electricity system needs to be updated
First to mention I survived the cold current from last year, the persistent cough required a bonbon with Melisa, hmm it calmed and so could cure.
Interesting work and IR cam heat análisis, looks you can heat by pancake coils a room with little input ? Nice to see that in one of the most affected country of the future climatic change there is a high motivation to come to a device that can take more energy out than in. A multi channel tuning regulator for load management might be necessary. Load prediction or a intermediate battery reservoir might be useful to be a device that powers everything, incl perhaps electric vehicles. Thumbs up for the instruction of coil and tuning practice data. Awaiting a load experiment with further insights.... Remember the resonance under load is a fugitive thing humanity wants to dominate , like squeezing a wet peace of soap that slips out of hands, so a intermediate energy reservoir will help in the sense of loading it back and not tuned for instant load power rather for quick recharge of a battery, comes to mind.
right, should be able to use a high freq to charge a big cap bank then use a timed switching circuit to discharge the cap bank to load or storage system. multiple isolated resonant coils within your wireless range that have external ground sources could be combined and rectified as well, no?
Don Smith in his later years released the schematics for the inside of his 'black box', and part of those schematics was an element which would automatically tune the frequency of the device depending on the load. Do you have any idea what he might've used, or have any ideas on replicating the same functionality in your future work?
Dear Donald L. Smith gave us everything he wanted to share in fact the test instruments and simulation softwares are not designed for this part of EM and Scalar waves (dielectric induction) . To summarize Don's technique 1. Store very high DC voltage in an electrolytic Cap bank that can be done using a ZVS a flyback tfr and a high voltage diode to produce high DC voltage to be stored in a cap bank. Use low value of cap but 2x the voltage you wanna store in the cap bank. Low value of capacitance will help in fast charging of the cap bank. It is must coz your rate of pulses should be minimum 2 times less than cap bank charge rate. 2. Now use spark gap or Master IVOs circuit to discharge that electrolytic bank through an LC tank circuit . The capacitor of LC tank circuit must not be electrolytic rather a ceramic or tantalum. That will produce very high ringing voltage. Use master Ivo's driver circuit or spark gap's gap to get high voltage spikes at a suitable frequency. If your coil's wire length is exactly equal to wavelength of that frequency then you do not need those tantalum capacitor. Your coil will be tuned and resonate at that frequency. Parasitic capacitance effect will be negligible in that case but it all depends upon if you use pancake or spider Web coils which have less parasitic capacitance. The choice of wire is also important. Do not use very thin wire to avoid skin depth threshold limit and Do not use very thick wire to waste extra material that is more than the skin depth at that frequency. Secondary CW or CCW pancake coils must identical in case of Don's Smith secondary coils where he connected inner ends of both coils to the ground2 and outer ends to the output. But if you use the outer ends to the input if a full bridge rectifier then one of your coils whose CW or CCW convention is same as that of your primary coil , make that coils inductance 2x of the other coil or 2x lower. This is very important. Let the resonance play rest of the game. Due to this high voltage and current you can use some part of it to be rectified as DC but then voltage and currents will be drastically reduced. Always use two separate grounds one for primary and other for secondary.
PLL Phase Locked Loop comes to mind. But esp32 with sensors and a decent program should also work.
@@MasterIvo Appreciate the answer! I'm newer to electronic engineering in general, but your content is super enthralling
Interesting... You know six pyramids make a cube/ box. I wonder if it's similar to my device.
With each video, things become clearer.
I’m very interested to see wich loads the circuit will power.
Maybe it will be possible to measure power in and out, getting overunity with the help of the earthed positive?
Great work.
Cheers.
Thanks! We shall see.
Always Great when a video from you is released...thnx Ivo
My pleasure!
Have you ever looked into Stanley Meyer and his water fuel cell. He aimed to get voltage to build and resonate waters dielectric properties while the water capacitor being leaky from some impurities making it not perform as such. He claimed to elongate the dipole molecule while there being free electrons within the water that could disrupt the covalent bond of water in a way that require less energy than current chemical method electrolysis..
I'm not interested in particle physics. I am fusing the fields
@@MasterIvo when it comes to a water powered car. the energy is being made in a reactive component (capacitor gap) all in the inventors writing he repeats particle oscillation as a energy generator.. the particle oscillation spoke of is reactive energy in the gap reacting with charged particles. so although you say your not into particle physics.. but what if it evolves around reactive energy! the is 2 means of reactive power from water.. electrolytic and dielectric. charge particle migration toward electrodes and dielectric polarization.. Love your videos!!!!
Sharing this because your smarts are up to the Challange!
Hello Ivo, I am also researching the radiant energy of Tesla, I really like your work but there is something that is not clear to me, when you say displacement current are you referring to longitudinal energy? On the other hand I do not understand what you use the output coil for. The middle one I see is 90° out of phase. I think that longitudinal energy is perhaps better used in a different way, without rectifying it for example since it is different from an electromagnetic wave. I always think that Tesla did not use diodes or semiconductors. Greetings from Argentina
Ivo, thank you for the previous responses. I am going to be ordering the component parts in about two weeks to build your system. I know you have given all the part info in the video because you havent updated your website. Any chance when you update the component list you can let us know. Just want to make sure I dont miss anything. Thanks again.
component list is good. just read on the page where to place c21
Excellent work. Thank you so much!!
Glad you liked it!
Great work Ivo
Thank you! Cheers!
thank you Ivo all your involvement is really appreciated and fair and above all very scientific you do not skip the steps each of them leads to the learning of Mr. Nikolas Tesla and this is very authentic of you. Thank you very much for all your sharing!!
Much appreciated
Great job Ivo.
Thank you!
Very Nice Master Ivo. You know what if you only use these pan cake coils without tuning capacitors but with a specific length of the wire which is equal to full wavelength of the frequency and then higher even or sub even hormonics for current and output coil you will get more energy as compared to LC tuned coils. The parasitic capacitance is sufficient to play as the C for the LC tank of each coil. Only one single frequency from function generator and at the secondary use higher or sub even harmonics of that frequency. Give me a token of prayers. Becareful that sub harmonics increase voltage a lot and higher harmonics increase current. So it's a tradeoff. Use one hand in the pocket rule and dry wooden table under the feet. But if you use CW and CCW fashion then both goes up being in phase. Best of Luck.
I am very interested in your comment on Ivo using even or sub even harmonics. Can you please explain to me how these harmonics can create higher voltage and current. If there is any source material that I ypu know of would be helpful
as well. Thank you.
Very nice work sir.
I'd like to brainstorm with you on something. But this isn't the setting I'm looking for might you have an email to contact or discord. Ever find much interest for piezoelectricity??
You might need to find a better replacement than the paper. Ofc the coils are bound together with some of the other options. silver is my go to for wire much greater results using it.
The proportion of the coils and the source are my keys for resonance. Piezoelectric crystals are very predictable. As are the sizes of the coils. The load also stays the same in the device the ways you collect it affects the output.
I like you have my own ideas sir. And like Nikola Tesla I to admire anyone with their own ideas. ♾️🙏🏼 Ones that make sense anyways lol. Some people live in a fairytale land I do not.
Would be interesting to see a useful (resistive/inductive) load connected to the output coil :)
Noted. if it is intesting I will show it
@@MasterIvo cant wait to see it, Master Ivo you are incredible person! Keep it up
The good old 74123 (well the HC one), nice to see it in use again! :)
its the HCT version, which works with wider voltage range, this way I can use it with the TL494
thx a lot very intresting =D
Glad you liked it!
Another fantastic video, as per usual. I am constantly checking your channel almost daily for updates and I get so excited when MasterIvo uploads! 🎉
For me you're, a modern day Nikola Tesla❤
Glad you like them!
A second question. I believe that standing waves store energy and can be pulled from the nodal points. Does that seem valid to you? Also, Tesla spoke of Stationary waves and i dont believe these 2 are the same thing. But not sure what the difference is do you? Thanks again.
I dont know
Great video, especially going through the tuning in detail, and how sensitive and reactive it is to shorting the HC coil. A question I have, can one fine tune with a variable air capacitor? Is that quality enough to allow to fine tune?
it is possible in theory , but the capacity needed is so big that it isn't practicle. I now adapted a switched capacitor tuning board with its smallest capacity being 10nF. In fact It needs 5nF. but often air capacitors are max 500pF. so that is to small.
@@MasterIvo Yes okay, I understand. I purchased a 2000pf, but I figured it would be good to fine tune near the end of tuning once you are very close with other added parallel capacitors. Great work sir.
@@fernandogigliotti2299 thanks, yes that makes sense, as a final finetuner
Great work Ivo.
It's hard to me to understand all these stuff, but tell me please:
Your input power was about 52w and the output about 100+ KW ?
And getting HV and HC in phase, you can power a load, right?
Thank you
I wish it was that easy, in theory there is potential power available in the fields, but it is not yet powerimg a load, so more development is needed
Hi Ivo, thanks for the new info.
But i missed what your aim is. is it about discovering properties in new terrain, or do you have an endgoal in sight. Cheers
discovering, sharing, explaining. The goal is free electricity second goal is field propulsion third goal is electric health benefits.
Finally, delay and coax cable are in place, congrats,bird_eye
Ivo,
I have looked at Guilliem's lumped constant networks and he states that the only way to transmit power is through resonance and harmonics. he doesn't say how harmonics are used. Can you help me understand how harmonics can be used for power transmission? Thanks.
I don't see how that would work
What are you working on that uses ferrite cores? saw your alixp review :)
ah I tried making a choke, to limit the magnetic current, but found the square wave method works easier
1. Is the coil & capacitor coil at the same values
2. You should put them in series
3. How are you PULSING IT.
4. Is the GROUND in-between the L & C
L 100mH C 100mF
1 no
2 which and why?
3 square wave on the high current coil is 80ns impulse of severeal hundred volts combined with th3 capacity
4 I do not understand the question
I use earth ground on the output coil only, which is tied tonthe copper water pipes of thr street
What's your thoughts on PEMF and have you looked into it?
I heard of it. Medical devices. it's interesting.
nice
It would be interesting to see how this setup would work with a Rodin Coil, considering the affects of the Rodin Coil on frequencies. Would it give you more fine-tuning capability?
It would be hard to capacitive and inductive couple.
drive that with RF NOISE
So if I understand this correctly you need a constant value load like an inverter in order to not require re-tuning when powering random utility loads. Correct?
no, I need a pure resistor , not an inductor or a capacitor as a load .
why people do not use easily RF NOISE driver :)
What exactly is your point? Did you tried to measure the power in? And power out?
You say the voltage and current are in phase but those are not in same closed circuit
The fields are in the same time and space, which is essential
As far as wording convention goes. This is the closest thing to a flux capacitor that I've seen.
Hello Ivo from Rusland
Hello there!
wow that is a lot of power ivo , in the next video which am sure you will test this tuned system to your resistive load , can you go over the push pull transformer part not clear if its a custom built , if you can also do like a digram , good job man
Thanks. Push pull, is like the half bridge circuit, which drives the primary of the high voltage ac transformer (black box)
Very nice! I have to get my signal a stable wave, but it’s weird because our frequencies are the same after tuning..
This is probably one of the most informative videos you’ve posted, very much appreciated! I’m sure I’m not the only one working on this as well, I know they are excited, haha
Dear Master Ivo! Any weird or paranormal effects during this experiment or series of these experiments related to resonance and high Q please?
Nothing so far.
How about a Conical Tesla coil designed to maintain angles needed to maintain Phi proportions? Similar to the Giza Pyramid.
tried that years ago. in theory the magnetic field would be stronger on one side
Excellent work Ivo! Could you share the manufacture and part number of the push-pull high voltage transformer?
I'll have to look it up, it was a small webshop from Austria
@@MasterIvo I found a 15kV AC Flyback Transformer High Voltage on ebay from a shop in Austria. Thank you Ivo!
@@JochumTed flyback has a diode and doesn't give ac but pulsed dc!
@@MasterIvo Okay, thanks for the heads up.
are u living in austria?
Last question for now I promise. About a year ago when you were trying to figure out max current and max voltage I had recommended in a comment about the water hammer concept. Just wondering if that helped any in your research whereby I thought may having 1 coil
for current and anothee for voltage and just like a water hammer if timed correctly the backflow will be reinforced by the forward flow to create a higher out flow of water. Like when you
turn on a garden hose really fast water doesn't flow out initially and then spurts farther than usual. Just curious if I helped any in you research. if not that ok.. Great Work.
yes the waterhammer, no I could not integrate it
thanks uuuuuuuu
Tuning forks ring with sympathetic resonance. Is it the same electromagnetism? Frequency and vibration.
Yes, when electric systems are tuned to the same frequency they do that also
Audio frequencies are the initial portion of Electromagnetic spectrum the higher you go the same principle is repeated but with different input and output transducers. e.g in audio range you produce sound with striking two objects, tuning forks, musical instruments. Then in electrical systems you produce sound from a transducer like speaker. But in Radio frequencies your sound is transmitted carried over radio frequencies (modulation) and then received by a radio receiver demodulated into same audio frequency and played by the radio sets speaker. I miss Sir Nikola Tesla and am his great fan. He once said these beautiful words, "If you need to know the secrets of the universe, think in terms of energy, frequency and vibration. "
And he also said that which is so unfortunate due to obvious reasons, "No free energy device will ever reach the market."
@@qinaan I feel you're confusing the medium. Audio uses air. EM uses the Aether to vibrate. frequency is periods per second so infinite.
Yes everything is vibratimg energy. the whole universe.
we need free electricity for the people, the market will adapt
@MasterIvo just hijacking this thread here, why is it that the only people I see referring to the emf needing a medium of transfer is electrical engineers....
@@jumpinjaxs because a wave is not a thing, a wave is what something does. The water is waving. So what is waving with EM?
Ik herken de spoelen uit de inductiekookplaat. Zelf ben ik er ook een aan het slopen. Zou het niet zo zijn dat de pan die uiteindelijk op de kookplaat wordt gezet de werking van de spoel beïnvloed? In het centrum van de spoel zit in de inductiekookplaat een censor die controleert of er ook werkelijk een pan aanwezig is. Die zit daar niet voor niets. Door de spoel onbelast te laten werken lijkt het mij zo dat dit van belang moet zijn, wat zou het verschil zijn als de spoel normaal belast zou worden?
de Q factor en inductiviteit veranderd, omdat de pan energie wegneemt van het wisselende magnetische veld van de spoel. dus er zal een auto tune circuit inzitten. ZVS is daar perfect voor.
I saw from wiliam enki before, but great , good way
Really? Can you post a link or tittle? would love to see that
miss that guy... does he upload anywhere still? havent seen his channel anymore.
oh wow, I've got the pintek pa-677 current probe, and I'd wondered why the measurement was so sensitive to the position of the probe....
Yes, I'm thinking about putting copper tape on the clamp mouth and earth grounding it, but that will probably still give problems.
But it is a way to look at the displacement currents!
@@MasterIvo for now it's a good lesson for where to clamp the meter, i.e. to probe the current at quiet places near outer edges and low ends of things 🤷
❤
Have you considered building a “graviflyer”?
ruclips.net/video/CCUWs02HK_M/видео.htmlsi=luuCHWHsLLlE1qtx
I am working on building a vacuum chamber, to show field propulsion
@@MasterIvo Nice.
Tesla: "It was right there the whole time" 🤦♂️
What is this used for?
still in research mode, working towards power generation
I am not trained in electronics, so I have to ask, what is the objective of all these experiments and what will be the final real world outcome(s).
Learning what can be done, with the goal of free electric power
Ivo have you heard of Anapole antennae?
never
😊
I see you answer comments. What is the purpose of this device?
open source research into free electricity generation
Can't you put aluminum foil around the current clamp?
It might work, not sure how that will interfere with the magnetic current reading
I wish you could do practice first and theory after…
Thats Why I have chapters.
After you get over unity, next step is to autotune the circuit to the load and of course remove the input like Tariel Kapanatze. He has patent on it already
www.youtube.com/@tarielkapanadze9356
Is Tariel Kapanadze
Also resource channel www.youtube.com/@tarielkapanadzeresourcecha7972
I am aware of this. so close yet still so far
Lets let AI tune your coil using a software defined radio. Try using repeater values to experiment with.
Where is the load?
on my desk
What is the point of all this??? What am I missing???
learning step by step
Tesla made a transformer that would raise the amperage without raising the voltage! So, a $100.oo electrical bill would only be $10.00 But patent office won't let us see them! A Challange 4 you hope you succeed, we all need this 1 good luck brother!