I have a 2006 Lancer and it looks very similar to this one. Found it challenging to remove bottom bolts without going under the car. There are many tricks to removal but I found an impact wrench necessary.
I’m getting code po171 I’ve changed everything fuel pump, fuel filter, cleaned injectors, replaced Bank 1 o2 sensor, fuel pump relays, fuel pressure regulator. And I’m still getting the code I hear a vacuum leak but can’t see it at all is this where the issue is coming from my engine has hard starts and loses power when I press the throttle unless I let off completely and press it again
Hi, my brother had bought a galant and replaced the manifold where only one sensor doesn’t connect, not sure if he got a aftermarket one from a different model with the same motor, sensor said ifs, won’t run without that sensor obviously but is there any way around that? Does he need a pull another manifold off of a junkyard galant like I told him to begin with?
If you pulled from the same engine and model of the car wiring harness shouldn’t be an issue. Sometimes wiring harness hide under the part so you just don’t see it.
@@kashfix9160 I think he pulled it from an eclipse if I’m not mistaken, I just welded him a new mounting spot for that sensor and it runs and drives thanks brother 🙏
@@kashfix9160 I replaced the intake manifold gasket already I'm having other troubles if you could help with that. I'm getting code p0340 for camshaft position sensor circuit a bank 1 and I can't even get it to start up new fuel pump, new injectors, new alternator,new battery, starters good I did have to wire a new pigtail connector for the camshaft but idk if it's a bad ground or something else
I got error 4001 a lancer 2006 thought only to clean the egr and throttle body, do you recommend removing the intake anyway? Another question, do you know if the microfilter is changed to those injectors? Since I bought it I have only cleaned the injectors with pressurized. greetings good video.
You don’t need to remove intake a part it can be removed individually and it’s held with two 10mm bolts. Injector micro filter can be replace on many cars but I haven’t ever replace on Mitsubishi’s. You need to double check on that. Thanks for your comment and watching my video.
I have coolant leaking into my transmission speed sensor on left side of engine. Does not overheat..pressure test shows no leaks. What could be causing this? No one can figure it out. Sensor is swimming in coolant and causing shift problems. Cannot replace sensor until I find what's causing coolant leak.2001 mitsubishi galant v6
I got error 4001 a lancer 2006 thought only to clean the egr and throttle body, do you recommend removing the intake anyway? Another question, do you know if the microfilter is changed to those injectors? Since I bought it I have only cleaned the injectors with pressurized. greetings good video.
I have a 2006 Lancer and it looks very similar to this one. Found it challenging to remove bottom bolts without going under the car. There are many tricks to removal but I found an impact wrench necessary.
Nice bro! Keep making this Lancer fix videos please!
Can the intake manifold be clean
Yes. You can clean with a any cleaning agent like brake parts cleaner.
I’m getting code po171 I’ve changed everything fuel pump, fuel filter, cleaned injectors, replaced Bank 1 o2 sensor, fuel pump relays, fuel pressure regulator. And I’m still getting the code I hear a vacuum leak but can’t see it at all is this where the issue is coming from my engine has hard starts and loses power when I press the throttle unless I let off completely and press it again
Did you try replace Mass air flow sensor it does sound like you have a hidden broken hose somewhere run a smoke test if you can.
Did u ever figure out the problem?
Hi, my brother had bought a galant and replaced the manifold where only one sensor doesn’t connect, not sure if he got a aftermarket one from a different model with the same motor, sensor said ifs, won’t run without that sensor obviously but is there any way around that? Does he need a pull another manifold off of a junkyard galant like I told him to begin with?
If you pulled from the same engine and model of the car wiring harness shouldn’t be an issue. Sometimes wiring harness hide under the part so you just don’t see it.
@@kashfix9160 I think he pulled it from an eclipse if I’m not mistaken, I just welded him a new mounting spot for that sensor and it runs and drives thanks brother 🙏
So would this cause fuel smell, hard engine shaking, and white smoke from the exhaust
Could you describe more of your problem? White smoke could cause due to burning oil in engine or antifreeze parking into head cylinder.
@@kashfix9160 I replaced the intake manifold gasket already I'm having other troubles if you could help with that.
I'm getting code p0340 for camshaft position sensor circuit a bank 1 and I can't even get it to start up new fuel pump, new injectors, new alternator,new battery, starters good I did have to wire a new pigtail connector for the camshaft but idk if it's a bad ground or something else
@@isaiahwilliams2149 your timing belt could've slipped teeth
@@worldsslowestmustang it did
@@isaiahwilliams2149 bruh the funny part is I didn't even realize the comment was a year ago
I got error 4001 a lancer 2006 thought only to clean the egr and throttle body, do you recommend removing the intake anyway? Another question, do you know if the microfilter is changed to those injectors? Since I bought it I have only cleaned the injectors with pressurized. greetings good video.
You don’t need to remove intake a part it can be removed individually and it’s held with two 10mm bolts. Injector micro filter can be replace on many cars but I haven’t ever replace on Mitsubishi’s. You need to double check on that. Thanks for your comment and watching my video.
I have coolant leaking into my transmission speed sensor on left side of engine. Does not overheat..pressure test shows no leaks. What could be causing this? No one can figure it out. Sensor is swimming in coolant and causing shift problems. Cannot replace sensor until I find what's causing coolant leak.2001 mitsubishi galant v6
Sounds like you have a head gasket leak.
this doesn't look fun but I know i'll have to do it eventually on my 05 lancer. lol
Not too bad please try and let me know if you have any question
I got error 4001 a lancer 2006 thought only to clean the egr and throttle body, do you recommend removing the intake anyway? Another question, do you know if the microfilter is changed to those injectors? Since I bought it I have only cleaned the injectors with pressurized. greetings good video.