They still look fabulous, the shape and glaze finishes are stunning. What a shame there were some cracks. There are numerous reasons these can occur. Possibly you could read up on the many reasons why. Something might grab your attention, and you may relate to one of the reasons this could be happening to your pots. Outstanding work.
Thank you for the comment✨ It was unfortunate that there was a crack, but I was relieved that there was no water leakage👌 There might have been an issue with how the stamp was pressed as well. This all became a good learning experience😊👌
Nice pieces, pitty about the cracks. Maybe its an idea to let dry your greenware longer by putting them under lose plastic. Turn them (upside down) every day and again under plastic. After some days let the plastic off. Then wait till bone dry. Or bisc fire a bit higer at 980⁰C and the second fire lower at 1080⁰C. Succes 👍
Thank you for the valuable address✨ One possible cause of the cracks could be that I dried the piece a bit too quickly. Pottery is difficult, isn't it? 😁💦 If you don't take your time and work carefully, it can lead to mistakes. 😁💦
@@tsukashigechannel7447 no problem. Yes a guick drying process can cause cracks. Depending on the weather conditions. Where i live (the Netherlands) the conditions are rather cool and the moisture is high so drying goes relatively evenly. If you don't have those conditions the drying under plastic advice might help you out. Greetz 🌸
You live in the Netherlands, right? ✨ I would love to see the pottery you made as well. ✨ Do you use Instagram? If you do, I would love to see your photos. 📷️ We can follow each other. 😊 This is my Instagram account. instagram.com/massh.tsukashige?igsh=MWhwcnAxbzR6NHI3dA==
器の形もですが、釉薬の表情が良いですね。先生のオリジナルですか?とても素敵です。
コメントありがとうございます✨
いえいえ😅釉薬は市販の釉薬を重ね掛けしています😊☝️まだまだ先生なんて呼ばれる様なうつわでは無いのです😅ちなみに、このどんぶりは金彩を掛けてから、上から藁灰の白釉を重ね掛けしています💡粘土は白い粘土を使っています😊
もし機会があれば、この重ね掛けはタブーかもしれないですがやってみて下さい😊👌面白い風合いになります🎵
返信ありがとうございます。釉薬も教えてくださりありがとうございます!朝鮮唐津に似ていて素敵なので、試してみます✨
ぜひぜひ✨やってみて下さい😊👌✨
They still look fabulous, the shape and glaze finishes are stunning. What a shame there were some cracks.
There are numerous reasons these can occur. Possibly you could read up on the many reasons why. Something might grab your attention, and you may relate to one of the reasons this could be happening to your pots.
Outstanding work.
Thank you for the comment✨
It was unfortunate that there was a crack, but I was relieved that there was no water leakage👌
There might have been an issue with how the stamp was pressed as well.
This all became a good learning experience😊👌
Nice pieces, pitty about the cracks. Maybe its an idea to let dry your greenware longer by putting them under lose plastic. Turn them (upside down) every day and again under plastic. After some days let the plastic off. Then wait till bone dry.
Or bisc fire a bit higer at 980⁰C and the second fire lower at 1080⁰C.
Succes 👍
Thank you for the valuable address✨
One possible cause of the cracks could be that I dried the piece a bit too quickly.
Pottery is difficult, isn't it? 😁💦
If you don't take your time and work carefully, it can lead to mistakes. 😁💦
@@tsukashigechannel7447 no problem. Yes a guick drying process can cause cracks. Depending on the weather conditions. Where i live (the Netherlands) the conditions are rather cool and the moisture is high so drying goes relatively evenly. If you don't have those conditions the drying under plastic advice might help you out.
Greetz
🌸
You live in the Netherlands, right? ✨
I would love to see the pottery you made as well. ✨
Do you use Instagram?
If you do, I would love to see your photos. 📷️
We can follow each other. 😊
This is my Instagram account.
instagram.com/massh.tsukashige?igsh=MWhwcnAxbzR6NHI3dA==
@@tsukashigechannel7447 nor instagram, nor facebook
OK👌✨