very good your Vídio very complete and well explained this plane doesn't have very clear instructions so if it weren't for this Vídio I would have a lot of difficulties in assembling it thanks for Vídio
Multiplex airplanes are all so well built. I've got some other brands and they can't hold a candle to how much thicker/denser/tougher the foam on MPX is. I've got the original FC and have driven it straight into the ground before and it only crinkled the nose. Would like to see a different design on the firewall but otherwise this looks really nice. Great video.
In the end, you almost always find the Multiplex foamies have the edge. They seem just better developed and thought out. Plus they always fly superbly.......
Thank you gor this video. It was helpful a lot to me when deciding if I should get the RR or kit version, considsring I already Have all the electronics from my Funray that has unfortunately crashed. The motor is a bit longer, but I think I can squeeze it in. Awsome flying there as well, congrats!
Thanks, if you are not up to the motor measurements you have to make a wooden spacer, most likely you will only fix your motor with 2 screws, do not worry they are enough. Here this is another flight of another in blue version that I have just assembled ruclips.net/video/4sFyHai3Mkg/видео.html
9:07 you should put all the servo cable in the next cavity on the fuselage and the prolongation cable let extra 4 cm in case of servo failure you cannot change the servo if apply your method
The kit version lacks all the electronics, so the extensions of the servo cables are also missing. The propeller is not included either, but by purchasing the kit version and all the necessary I have saved about $ 100 compared to the pnp persion which here where I live costs about $ 300, so I spent a total of about $ 200
I am dazzled by your dexterity with it's PLANE I just bought it I have an average indoor level Would you be kind enough to give me your settings (Expo and travel) on the three control surfaces
Hi! I've got a doubt about flap servos. They are assembled in simmetric or mirrored position. So, if I use a 'Y' cable to connect both servos to the same channel, they would move in opposite direction. How is it solved? Thanks
@@e_Duardus sure it works :) otherwise experiment soldering on a old servo. but i did serveral this way and none has failed so far... even servived my crashes lol
Buongiorno RCReporter! Ho guardato il tuo video con attenzione una paio di tempi e mi ha aiutato molto. Ma ho aspettato la instalazione d il motore e gli altri componenti elettrici. Sono stato molto arrabbiato per non avere provato il motore con buchi tradizionale prima di avere incollato la fusoliera. Ora ho leggo che qui in la Germania raccomandano avitare il motore tradizione con solo due viti. Altri persone sono costruiti adattatore (con la stampante 3D o di legna) per montare il motore. Cosa hai fatto tu? Una altra domanda: perché ancora non aveva ricevuto migliore servi (servo), ho montato i servo MG90D indietro come te. Hai avuto buone esperienze con loro? Supongo cue cambiare i servo indietro e molto difficile... Grazie mille e molti saluti di Baviera di un mezzo germano, mezzo chileno.
Ciao, ho montato il motore (sunnysky) creandomi un distanziale in legno, e purtroppo ho usato anche io solo 2 viti in quanto le altri due fori non combaciano con i fori del motore. Vai tranquillo regge benissimo anche con solo 2 viti
@@RCReporter super, grazie mille! Io ho comprato un motore surpass C3548. La lunghezza e quasi perfetta ma uno o due millimetri starebbero migliori per securita (distanza fra la elica e la fusoliera. Forse anche io posso fare un distanziale di legno o utilizo rondelli comune. In riguardo a i servi MG90D, tutto OK ? Ho avuto un incidente con il mio primo aereo di balsa. Non so se per la signale o per il servo MG90D.... Grazie e buona giornata!!
Very nice and useful video. Now I am assembling my FC NG, and have a doubt with the rudder and the vertical stabilizer. I suppose that I should cut the upper portion of foam that joins them and doesn'l let the rudder turn. But I can't find any pivot but the small hinge where the rear wheel is fixed. Is this hinge the only point where the rudder is held on?
Is it the same motor as the previous generation FunCub? I have a very worn older version, and would buy the NG kit if I knew the motor was up to the job..... Be careful you don't get cyano on the servo leads. It cracks the insulation on the leads, leading to failure.......
SunnySky X2814 1000Kv esc 40 amp propeller apc Electric 12x8 3s 2600 lipo. My version is the kit, I took 2 last year, this one in the video is the first, now I fly with the other one in blue. The latter I assembled it even better and this weekend I will mount the floats to go and fly on the lake here in the Gargano (Italy)
Saluti a Gargano! I would love you ti built my blue kit too xD. I also bought this for savings, but I thought it would be easier and the manual better. I’m from Bavaria (half Chilean too) and I’m impressed how poor the manual is… I have the same Servos as you but a bigger motor I think. 3548 from Surpass (1100kv). I hope I have time to build the kit soon. Your flying video looks like a lot of fun!! This week we travel to northern Italy 🇮🇹 Best regards!
I odrered plane and didnt know it needa gluieng and glue is not in the box. Also no ilustrations in the manual had to find them online. And mxr connector - dont like it.
![FendiDa Rappa - Clock Dat ft. Shamar Marco [Official Music Video]](http://i.ytimg.com/vi/3NBU8KHdxYY/mqdefault.jpg)
Awesome job! We can't wait to try out an NG. All our time and experience with Fun Cubs is with the OG model. Timeless airplane.
Incomplete guide, just like the manual they gave us.
Me too, waiting in the living room
very good your Vídio very complete and well explained this plane doesn't have very clear instructions so if it weren't for this Vídio I would have a lot of difficulties in assembling it thanks for Vídio
As a German I’m impressed how poor the manual is…. I was expecting like a LEGO manual….
Thanks god RC Reporter ha fatto un buon video!
Multiplex airplanes are all so well built. I've got some other brands and they can't hold a candle to how much thicker/denser/tougher the foam on MPX is. I've got the original FC and have driven it straight into the ground before and it only crinkled the nose. Would like to see a different design on the firewall but otherwise this looks really nice. Great video.
In the end, you almost always find the Multiplex foamies have the edge. They seem just better developed and thought out. Plus they always fly superbly.......
Nice video! But when and how will the motor be installed? It looks like you can't reach it once the 2 fuselage halves are together.
Nice video, thanks!
Question: what type of motor is used and how many battery cells? Sorry, can't find it in the video.
If you still have this funcub... I highly recommend using a VESS electric wood prop.
What happens WHEN servos fail that are embedded in the fuselage? You have to cut the whole plane open to swap out a servo?
Thank you gor this video. It was helpful a lot to me when deciding if I should get the RR or kit version, considsring I already Have all the electronics from my Funray that has unfortunately crashed. The motor is a bit longer, but I think I can squeeze it in. Awsome flying there as well, congrats!
Thanks, if you are not up to the motor measurements you have to make a wooden spacer, most likely you will only fix your motor with 2 screws, do not worry they are enough. Here this is another flight of another in blue version that I have just assembled ruclips.net/video/4sFyHai3Mkg/видео.html
Was für einen Kleber nutzt du für die funcub? Cooles Video
9:07 you should put all the servo cable in the next cavity on the fuselage and the prolongation cable let extra 4 cm in case of servo failure you cannot change the servo if apply your method
Were the servo extention cables included? Were the prop adapter, spinner and prop included as well?
The kit version lacks all the electronics, so the extensions of the servo cables are also missing. The propeller is not included either, but by purchasing the kit version and all the necessary I have saved about $ 100 compared to the pnp persion which here where I live costs about $ 300, so I spent a total of about $ 200
awesome
Se mi servissero accessori o pezzi di ricambio per questo fun cub?
I am dazzled by your dexterity with it's PLANE
I just bought it I have an average indoor level
Would you be kind enough to give me your settings (Expo and travel) on the three control surfaces
Hi!
I've got a doubt about flap servos. They are assembled in simmetric or mirrored position. So, if I use a 'Y' cable to connect both servos to the same channel, they would move in opposite direction.
How is it solved?
Thanks
desolder and switch the 2 outer kabels on the podmeter and the 2 wires of the servo motors. then servo is reversed! :)
@@Dragon69FlyTeam Finally I purchased a servo reverser (less than 10€). I hope it will work...
@@e_Duardus sure it works :) otherwise experiment soldering on a old servo. but i did serveral this way and none has failed so far... even servived my crashes lol
Buongiorno RCReporter! Ho guardato il tuo video con attenzione una paio di tempi e mi ha aiutato molto. Ma ho aspettato la instalazione d il motore e gli altri componenti elettrici. Sono stato molto arrabbiato per non avere provato il motore con buchi tradizionale prima di avere incollato la fusoliera. Ora ho leggo che qui in la Germania raccomandano avitare il motore tradizione con solo due viti. Altri persone sono costruiti adattatore (con la stampante 3D o di legna) per montare il motore. Cosa hai fatto tu?
Una altra domanda: perché ancora non aveva ricevuto migliore servi (servo), ho montato i servo MG90D indietro come te. Hai avuto buone esperienze con loro? Supongo cue cambiare i servo indietro e molto difficile...
Grazie mille e molti saluti di Baviera di un mezzo germano, mezzo chileno.
Ciao, ho montato il motore (sunnysky) creandomi un distanziale in legno, e purtroppo ho usato anche io solo 2 viti in quanto le altri due fori non combaciano con i fori del motore. Vai tranquillo regge benissimo anche con solo 2 viti
@@RCReporter super, grazie mille! Io ho comprato un motore surpass C3548. La lunghezza e quasi perfetta ma uno o due millimetri starebbero migliori per securita (distanza fra la elica e la fusoliera. Forse anche io posso fare un distanziale di legno o utilizo rondelli comune.
In riguardo a i servi MG90D, tutto OK ? Ho avuto un incidente con il mio primo aereo di balsa. Non so se per la signale o per il servo MG90D....
Grazie e buona giornata!!
Very nice and useful video. Now I am assembling my FC NG, and have a doubt with the rudder and the vertical stabilizer.
I suppose that I should cut the upper portion of foam that joins them and doesn'l let the rudder turn. But I can't find any pivot but the small hinge where the rear wheel is fixed.
Is this hinge the only point where the rudder is held on?
It is clear to me (it is shown in the video). Just cutting the upper portion of material, the vertical "strip" works as hinge...
@@e_Duardus yes, the central part acts as a hinge, then if it comes off you can use normal hinges to repair it
Is it the same motor as the previous generation FunCub? I have a very worn older version, and would buy the NG kit if I knew the motor was up to the job..... Be careful you don't get cyano on the servo leads. It cracks the insulation on the leads, leading to failure.......
SunnySky X2814 1000Kv esc 40 amp propeller apc Electric 12x8 3s 2600 lipo. My version is the kit, I took 2 last year, this one in the video is the first, now I fly with the other one in blue. The latter I assembled it even better and this weekend I will mount the floats to go and fly on the lake here in the Gargano (Italy)
@@RCReporter Useful information, thanks for the quick reply!
Saluti a Gargano! I would love you ti built my blue kit too xD. I also bought this for savings, but I thought it would be easier and the manual better. I’m from Bavaria (half Chilean too) and I’m impressed how poor the manual is…
I have the same Servos as you but a bigger motor I think. 3548 from Surpass (1100kv). I hope I have time to build the kit soon. Your flying video looks like a lot of fun!!
This week we travel to northern Italy 🇮🇹
Best regards!
ciao, che servi hai montato?
9gr ingranaggi in metallo
hola q motor montaste
hola cual son los grados de los flaps
Ciao..Che servi hai usato, îl link se poi dire e che colla ciano hai usato, lo stesso îl link per favore. Scusa îl mi-o italiano..Buona serata
how is that blue device at 22:06 called?
It is called a "servo tester"
I odrered plane and didnt know it needa gluieng and glue is not in the box. Also no ilustrations in the manual had to find them online. And mxr connector - dont like it.