Great video ty for sharing. Another trick that may help in the future that many people don't know/forget about is using COLD instead of heat... Putting that sleeve in the freezer for a few hours can shrink it enough (even a fraction of a millimeter helps lots) to get that thing pressed back in.... Also bushings work even better in the freezer since they're not metal they shrink more.
Separate the ball joint with a pickle fork and you won't have to mess with that bushing! Place a floor jack under the ball joint nut after loosening, put most of the car's weight on the ball joint and wail away on the pickle fork. several good whacks is all that's needed. Nice video BTW!
Informative video for my exact car. Thanks!!! Thanks Ford for ditching all your cars (except Mustang), not everyone wants to drive an F150 everywhere. Never will understand their reasoning behind that move. The Fusion (with some updates/refresh) could easily compete with the Honda Accord/Toyota Camry.
I spent a couple days trying to get those damn ball joints out of the steering knuckles. Ended up pulling the entire steering knuckle assemblies out with the lower control arms attached and installed my new control arms on a couple knuckles I got from my local junkyard for $50/piece. Well worth $100 to not have to continue hammering on those ball joints. LOL
He said he wasn't going to torque the bolts until he had weight on the wheel, he even went into good description of why its a bad idea not to preload the spring before tightening the bolts, 15:00. He only snugged the bolts down first.
I have a question. I replaced the same lower control arm. The old one was really bad (ball joint). Didn't have a problem with the steering at all. I installed the new part and the car pulls or steering pulls to the right. The steering is not where it was before .my mechanic told that I need an alignment. Any ide why?
Are all the subframes the same as well I have a 06 Mazda 6 3.0 Automatic duel Manuel 4 Dr Sedan and I can’t find one so can anyone help me with rechargeable crossmember subframes PLEASE
“Not that hard for doing on jack stands” me hearing that after watching another video of someone needing to lift the trans and lower subframe to remove the lower arms bolts
@@RepairGeek No, it is called saving the customer money, and their lives! Part changer like you are why Techs get sued! You should be lock in prison for ripping people off! It is much cheaper to do the job right the first time and not have them pay it again over and over again, because you are too stupid to understand how reality works!!!
@@RepairGeek Only changing one, knowing full well that all four need changed, as it is always known, is ripping someone off! You are a scammer and the reason people think poorly of techs.
@@inyoudeep1 cool. Next time I get a car in for a brake job I'll change the master cylinder and all the lines as well. Then, tell the customer I'm doing them a favor by changing everything. Makes total sense.
@@RepairGeek Changing only one, is like only changing one brake pad! You know it, but are trying to justify ripping people off and endangering their lives.
Great video ty for sharing. Another trick that may help in the future that many people don't know/forget about is using COLD instead of heat... Putting that sleeve in the freezer for a few hours can shrink it enough (even a fraction of a millimeter helps lots) to get that thing pressed back in.... Also bushings work even better in the freezer since they're not metal they shrink more.
Separate the ball joint with a pickle fork and you won't have to mess with that bushing! Place a floor jack under the ball joint nut after loosening, put most of the car's weight on the ball joint and wail away on the pickle fork. several good whacks is all that's needed. Nice video BTW!
Thanks for the video, this will help make the work on my wife’s car go easier! It’s nice to see the job done before going into it myself.
Informative video for my exact car. Thanks!!! Thanks Ford for ditching all your cars (except Mustang), not everyone wants to drive an F150 everywhere. Never will understand their reasoning behind that move. The Fusion (with some updates/refresh) could easily compete with the Honda Accord/Toyota Camry.
I just did the job on a 2011, did not mess with the suspension as the inside bolt was easy to remove.
Good video. I'll most likely be doing this on my Mazda 6 soon. Very harsh when hitting bumps and bushings are cracked.
Good job bro.
good video..i think i could do this ,ill watch again to be sure ive got it ..
Very nice video tanks
hello i have to change both sides back and forth for my 2007 fusion ford!
the question is Lateral Link Control Arm is the same, thank you
Excelent video
I spent a couple days trying to get those damn ball joints out of the steering knuckles. Ended up pulling the entire steering knuckle assemblies out with the lower control arms attached and installed my new control arms on a couple knuckles I got from my local junkyard for $50/piece. Well worth $100 to not have to continue hammering on those ball joints. LOL
Thanks buddy 💥
Driver side? On the V6 do you have to lift the engine up to get the subframe bolt out from the rear center arm?
Yes.
Before tightin nuts preload tha spring to 15 7/8
He said he wasn't going to torque the bolts until he had weight on the wheel, he even went into good description of why its a bad idea not to preload the spring before tightening the bolts, 15:00. He only snugged the bolts down first.
I have a question. I replaced the same lower control arm. The old one was really bad (ball joint). Didn't have a problem with the steering at all. I installed the new part and the car pulls or steering pulls to the right. The steering is not where it was before .my mechanic told that I need an alignment. Any ide why?
congratulation, thank you!
You can get replacement boots for a fraction of what the arm costs.
Are all the subframes the same as well I have a 06 Mazda 6 3.0 Automatic duel Manuel 4 Dr Sedan and I can’t find one so can anyone help me with rechargeable crossmember subframes
PLEASE
Can a 2007 Mazda 6 rear l Lateral arms interchangeable with AWD 3.5L Fusion sport rear Lateral arms ? Does anyone know? Stay Frosty All 🥶
Does this not apply to the 2008 Mazda 6?
The setup looks the same in my Mazda 6 mark 1, body type GG
6:00 never grip it on the sleeve .. just press it out
you could have lowered the sub-frame to get that rear control arm bolt out, it's pretty easy to do.
“Not that hard for doing on jack stands” me hearing that after watching another video of someone needing to lift the trans and lower subframe to remove the lower arms bolts
It's needed for the driver side my brother
@@mtsanchez27 yeah
My only real issue is that you only changed one! You should have changed all four! No self respecting Tech would only change one.
Yep only changed what was broke, instead of ripping someone off for all 4 😂 and that's apparently a bad thing?
@@RepairGeek No, it is called saving the customer money, and their lives! Part changer like you are why Techs get sued! You should be lock in prison for ripping people off! It is much cheaper to do the job right the first time and not have them pay it again over and over again, because you are too stupid to understand how reality works!!!
@@RepairGeek Only changing one, knowing full well that all four need changed, as it is always known, is ripping someone off! You are a scammer and the reason people think poorly of techs.
@@inyoudeep1 cool. Next time I get a car in for a brake job I'll change the master cylinder and all the lines as well. Then, tell the customer I'm doing them a favor by changing everything. Makes total sense.
@@RepairGeek Changing only one, is like only changing one brake pad! You know it, but are trying to justify ripping people off and endangering their lives.