I worked team 5 At JEP in 94/1995 assembly line and before I installed the valve cross-heads. I was finding an inordinate amount of misaligned half locks in the valve spring retainer. That got the engine pulled off the line til the repair was made. The pointing fingers between the head line and assembly was comical, I must have found a dozen or so over time until it was rectified that had me with TOP "good Catch" overall finds write-ups for the team I was at 40 percent and 2nd place was my friend Doug at 10 percent.....and down from there for other employee's. A friend from test showed me a disassemble engine that ate a valve and it was destroyed. Being a mechanic gave me the edge to spot problems where most others were just droids putting in they're time. so what did they do when production was lowered; they booted the temp (me), so some other got to stay on. The line was producing the L10 and the M11 engines at that time
@@truckerstyleshawn place called heavy diesel tuner in Cleveland Tn nice folks but damn expensive 1,499 for custom tune and rebuild of ecm but can’t find anyone else that will mess with m11 celect
can i remark my accessory pulley by going off of the valve position? mine is A for 1and 6 so could i do cylinder one valves closed to know that i’m at “A” and remark the pulley, i’ll replace it anyway but i figure i’ll need to clock the position regardless.
Hey yall i got a 2001 cummins ISM. The oil starts out at 65 psi then drops into the teens after warming up and it drops at the filter head Ive ruled out pump, guage, leaks, injectors, jakes while everything on the valve train looks good. I had a 12 hour diagnostic that ensured the internals had normal ware. I recently had the injectors in cylinder 2 replaced as well as a rocker arm on the same cylinder replaced. I used the truck for two days and had to bring it back to the same shop. The mechanic informed me that there was a wire broken on the number 2 jake assembly. And now insists that it wasnt from the work they did but dosent know whats wrong with it please any suggestions will be greatly appreciated
I worked team 5 At JEP in 94/1995 assembly line and before I installed the valve cross-heads. I was finding an inordinate amount of misaligned half locks in the valve spring retainer. That got the engine pulled off the line til the repair was made. The pointing fingers between the head line and assembly was comical, I must have found a dozen or so over time until it was rectified that had me with TOP "good Catch" overall finds write-ups for the team I was at 40 percent and 2nd place was my friend Doug at 10 percent.....and down from there for other employee's.
A friend from test showed me a disassemble engine that ate a valve and it was destroyed.
Being a mechanic gave me the edge to spot problems where most others were just droids putting in they're time.
so what did they do when production was lowered; they booted the temp (me), so some other got to stay on.
The line was producing the L10 and the M11 engines at that time
Thank you. I'm doing a valve adjustment on a stupid old Minnesota DOT Snowplow that is all rusted up from salt.
Mines due too need to get it done before my ecm gets back from the tuner and I put that 450hp custom tune on the poor lil motor lol
That will be nice! Hope you got a ism block stiffener
@@truckerstyleshawn oh yeah got it ordered yesterday
Where did you get it tuned?
@@truckerstyleshawn place called heavy diesel tuner in Cleveland Tn nice folks but damn expensive 1,499 for custom tune and rebuild of ecm but can’t find anyone else that will mess with m11 celect
I’ve got jakes to deal with need to find the specs on that I guess before I do it
Trouble weak Jake brake on m 11 plus , need know adjusting .
How to check compression of Cummins QSM11 engine? And what about standard compression pressure??
Hi when you are on number 3 valve is the injector rocker supposed to be loose
can i remark my accessory pulley by going off of the valve position? mine is A for 1and 6 so could i do cylinder one valves closed to know that i’m at “A” and remark the pulley, i’ll replace it anyway but i figure i’ll need to clock the position regardless.
Hey yall i got a 2001 cummins ISM. The oil starts out at 65 psi then drops into the teens after warming up and it drops at the filter head Ive ruled out pump, guage, leaks, injectors, jakes while everything on the valve train looks good. I had a 12 hour diagnostic that ensured the internals had normal ware. I recently had the injectors in cylinder 2 replaced as well as a rocker arm on the same cylinder replaced. I used the truck for two days and had to bring it back to the same shop. The mechanic informed me that there was a wire broken on the number 2 jake assembly. And now insists that it wasnt from the work they did but dosent know whats wrong with it please any suggestions will be greatly appreciated
I would pull the oil pump and shim it or Chang it out. That’s what I would do.
Do I need to do that to replace a power steering pump base on my 350 engine
Think I can get a link for that diagram and manual
My m11 engine start run and just shut down and don't know the problem
I have qsm 11 engine knocking problem abosorve above after1500 RPM give us suggestions