Straightforward explanation. But didn't work for me until i figured out to set the auxiliary channel for channel 6 to source none. After that, it worked perfectly.
Michel P Thanks for this very good video. But I can see 2 drawbacks for indoor models : it needs 5 channels and 3 mixes. A fellow of my Indoor club, that built a Concorde plane with 2 motors and no rudder, was in trouble to turn. I find out the following solution that uses only 2 mixes and is compatible with 4-channel indoor receiver. Channel 1 and 2 are used for elevons and channel 3 and 4 for motors. Here is the configuration. The left motor is connected to channel 3 (CH3) and controled with the throttle stick, The right motor is connected to channel 4 (CH4) and controled with the rudder stick, Channel 3 and 4 need to be reversed with my transmiter , MIX-1 controls both motors and MIX-2 speed down one motor while speeding up the other one. Rudder trim needs to be push to the right to prevent controller to beep. MIX-1 : ON Master : CH3 Slave : CH4 +100% +100% MIX-2 ON Master : CH4 Slave : CH3 -100% -100%
Typo error in my previous message is corrected below. Using the joysticks of my Flysky FS-i6S, how do I variably control three motors to have the same RPM according to three mixes so that each mix has one motor rotating opposite to the other two as shown below. Is this even possible? Mix 1 Motor A - Forward Motor B - Reverse Motor C - Reverse Mix 2 Motor A - Reverse Motor B - Forward Motor C - Reverse Mix 3 Motor A - Reverse Motor B - Reverse Motor C - Forward Thank you.
Thank you so much for this.I did all the steps like you did but I do have one error the motor in channel 3 keep peeping and not rotate.Please note I did switched the 2 motors on receiver and working always in channel 6 but channel 3 what ever is the esc not working with a lot of peeping.
Are you using 12A Blheli esc ?? In some ESC lower point is specific and the lower point of CT6B is little bit high, so you can correct it in 2 ways: First make the EndPoint of Ch3 is 120% (Both) then 1) Adjust the trim of Ch3.(Down) OR 2) Cut the throttle by using the throttle cut switch, before connecting lipo.
Sadly not working ch3 goes maximum to 25% in the display option and ch6 is always on 100% but is somehow going down to 0% for very short amount of time can someone help me?
Great video. Using the joysticks of my Flysky FS-i6S, how do I variably control three motors to have the same RPM according to three mixes so that each mix has one motor rotating opposite to the other two as shown below. Is this even possible? Mix 1 Motor A - Forward Motor B - Reverse Motor C - Reverse Mix 1 Motor A - Reverse Motor B - Forward Motor C - Reverse Mix 1 Motor A - Reverse Motor B - Reverse Motor C - Forward Thank you.
thank bro... your language is good, you video good, your sound is good, and everything is perfect!!! very easy to understand... I very like u brooo.. thanks!!!
www.banggood.com/Flysky-FS-i6X-2_4GHz-10CH-AFHDS-2A-RC-Transmitter-With-X6B-i-BUS-Receiver-p-1090406.html?6805044548439201605Q OR www.banggood.com/FlySky-FS-i6-2_4G-6CH-AFHDS-RC-Transmitter-With-FS-iA6B-Receiver-p-983537.html?6805044548439201605Q
Bhai el problem hai please solution BTAo ..bhai mene tumhari. Video dekhkar difference throttle setup kiya pr jab mai stick ko left krta hu to left hi moter chlti hai aur right band ho jati hai jab right mai stick krta hu right ki moter. chtli hai aur left ki band ho jati hai bhai aesa kyu hota hai aur bhai jab mai throttle ko 100% kr deta hu right wali moter band kyu ho jati hai apne aap bina propeller ke 100% karuga to nhi band hoti pr jab propeller lgi hoti hai tab 💯% throttle kr duga to keval right ki band hoti hai please bhai reply fast mujhe bhut jrorat hai apke help ki 😟😟😟 bhai please help me
connection check karo left right me problem ho to channel ko swipe karo matlab right ko left ki port malagao aur left ko right ki port me lagao. aur motor stop sayed connection problem hoga
![EST Gee - NEVER NEED (Feat. Selfpaid Savage) [Official Video]](http://i.ytimg.com/vi/f2cRtr52HXI/mqdefault.jpg)
Straightforward explanation. But didn't work for me until i figured out to set the auxiliary channel for channel 6 to source none. After that, it worked perfectly.
omg i was freaking out because it wouldn't work until i saw this thanks
I think he is talking about the FS-i6. Usually Channel 6 is mapped to one of the AUX Switches which probably need to be unassigned.
David S. Yes
Olaf Schmitz thanks!
dude you save my day
Michel P
Thanks for this very good video. But I can see 2 drawbacks for indoor models : it needs 5 channels and 3 mixes.
A fellow of my Indoor club, that built a Concorde plane with 2 motors and no rudder, was in trouble to turn. I find out the following solution that uses only 2 mixes and is compatible with 4-channel indoor receiver. Channel 1 and 2 are used for elevons and channel 3 and 4 for motors. Here is the configuration.
The left motor is connected to channel 3 (CH3) and controled with the throttle stick,
The right motor is connected to channel 4 (CH4) and controled with the rudder stick,
Channel 3 and 4 need to be reversed with my transmiter , MIX-1 controls both motors and MIX-2 speed down one motor while speeding up the other one. Rudder trim needs to be push to the right to prevent controller to beep.
MIX-1 :
ON
Master : CH3
Slave : CH4
+100%
+100%
MIX-2
ON
Master : CH4
Slave : CH3
-100%
-100%
Thank you ! This really helps me
Thanks a lot! I've being trying different ch/percentage/offset combination without success until now.
Love this community
Thanks for this! Worked for me, except I had to tell mix 1 to have a -50 offset to set them in sync. Thanks again!
You made my day brother .thank you
wow, this is superb
Wowwwww thank you so much
Thank you , that was helpful. I just subbed 😊❤
Very helpful, thanks!
Very helpful thanks
muchas gracias por la informacion thanks
Are you from Spain???
Thank my friend. Very helpful
Welcome
Typo error in my previous message is corrected below.
Using the joysticks of my Flysky FS-i6S, how do I variably control three motors to have the same RPM according to three mixes so that each mix has one motor rotating opposite to the other two as shown below. Is this even possible?
Mix 1
Motor A - Forward
Motor B - Reverse
Motor C - Reverse
Mix 2
Motor A - Reverse
Motor B - Forward
Motor C - Reverse
Mix 3
Motor A - Reverse
Motor B - Reverse
Motor C - Forward
Thank you.
very helpful. Tq
thanks soo much
bro.can u tell me the mixing of twin motor for only throttle??can i get the same rpm with single battery?
Can i do this with i4x
Thank
Thank you so much for this.I did all the steps like you did but I do have one error the motor in channel 3 keep peeping and not rotate.Please note I did switched the 2 motors on receiver and working always in channel 6 but channel 3 what ever is the esc not working with a lot of peeping.
Are you using 12A Blheli esc ??
In some ESC lower point is specific and the lower point of CT6B is little bit high, so you can correct it in 2 ways:
First make the EndPoint of Ch3 is 120% (Both) then
1) Adjust the trim of Ch3.(Down)
OR
2) Cut the throttle by using the throttle cut switch, before connecting lipo.
Sadly not working ch3 goes maximum to 25% in the display option and ch6 is always on 100% but is somehow going down to 0% for very short amount of time can someone help me?
Qué radio ocupas yo lo hice en el flysky y si funciona..
Hi, can this setup be used for ESCs with reverse? Hope you can help. Thanks...
Yes, you can
MakerHand thanks for the reply, can you do a video showing how to do this please?
Great video. Using the joysticks of my Flysky FS-i6S, how do I variably control three motors to have the same RPM according to three mixes so that each mix has one motor rotating opposite to the other two as shown below. Is this even possible?
Mix 1
Motor A - Forward
Motor B - Reverse
Motor C - Reverse
Mix 1
Motor A - Reverse
Motor B - Forward
Motor C - Reverse
Mix 1
Motor A - Reverse
Motor B - Reverse
Motor C - Forward
Thank you.
with only 3 mix it's not possible
thank bro... your language is good, you video good, your sound is good, and everything is perfect!!! very easy to understand... I very like u brooo.. thanks!!!
please help me to grow
PRoF JaiLaNi your address and phone number
@@deepak_raj_rider01 why?
Thanks,,,, very help
Both Motor's are running as soon as I turned on the transmitter and from there by increasing speed by giving throttle. What should I do?
please check your transmitter's lower throttel value and calibrate the esc
Can i use this setup for making rc tank?
Yes you can
how to for radiolink t8fb
Is there any requirement of mixing in 8 channel receiver ??
No, the process will be the same
Where did you buy Flysky FS i6 transmitter and receiver
www.banggood.com/Flysky-FS-i6X-2_4GHz-10CH-AFHDS-2A-RC-Transmitter-With-X6B-i-BUS-Receiver-p-1090406.html?6805044548439201605Q
OR
www.banggood.com/FlySky-FS-i6-2_4G-6CH-AFHDS-RC-Transmitter-With-FS-iA6B-Receiver-p-983537.html?6805044548439201605Q
Can you do this with a rc car transmitter?
Only, if mixing is available
What is the max range of fs-ct6b transmitter?
I pushed up to 600 meter
Awesome video! Worked perfectly, is there a way though to not use that 3rd channel?
Sorry! you can't do that because this TX has only 3 mixes.
I did this. But one of my two motor's is starting late. Any suggestions??
calibrate ESC
MakerHand It worked!Thanks a lot!
I have the same issue...How do I calibrate my ESC's?
Do we need separate batteries for separate motors ? If not how?
No, you don't need separate battery just connect both ESC together with a single battery
Bhai el problem hai please solution BTAo ..bhai mene tumhari. Video dekhkar difference throttle setup kiya pr jab mai stick ko left krta hu to left hi moter chlti hai aur right band ho jati hai jab right mai stick krta hu right ki moter. chtli hai aur left ki band ho jati hai bhai aesa kyu hota hai aur bhai jab mai throttle ko 100% kr deta hu right wali moter band kyu ho jati hai apne aap bina propeller ke 100% karuga to nhi band hoti pr jab propeller lgi hoti hai tab 💯% throttle kr duga to keval right ki band hoti hai please bhai reply fast mujhe bhut jrorat hai apke help ki 😟😟😟 bhai please help me
connection check karo left right me problem ho to channel ko swipe karo matlab right ko left ki port malagao aur left ko right ki port me lagao. aur motor stop sayed connection problem hoga
How to do flapleron using ct6b
ruclips.net/video/PklC57SR56k/видео.html
Link is in the description of the video
How to make a four motor throttle can you explain please
You need 'Y' servo connector
Can we join our normal 2 wire dc motor plz answer i am suffering
you need brushed ESC
Necesitas 2 esc brushed motor para poder conectar y hacer la mezcla.
Sir can you upload a video that at10 trhuttale set up
I try to turn mid-air using this method. My plane just rolling. It is not making smooth turn.
you need to apply little aileron and little practice.
Thanks a lot bro..... But how to connect 4 motors
y splitter servo cables
peruvian , SUD AMERICA , CUAL SERIA LA ROTACION DE LAS HELICES PARA QUE VUELE UN AVION BIMOTOR
What??😕
Sorry, I can't understand what you say. Can you speak English please??
Un motor en rotación como el reloj y el otro al revés, solo cambias uno de los cables entre la esc y uno de los motores
The problem with this is that you dont have any spare mix to do the flaps
You don't need mix for flaps use a switch for flaps in 10channel transmitter and receiver
My throttle is not working as u said
In which TX???
Bhai hindi me banou video
My HINDI channel
ruclips.net/channel/UCO8uCN1q7dMlFum6iJzv48A
bhaiya apka phone number do mujhe apse kam hai
See the "About" section of my channel
chandan singh