Just a tip, before turning off idle it all the way down before turning off. Good habit for all engines. Its hard on them to go from running wide open to instantly shut off
I've used this sprayer several times now on brick pavers, a wood deck, patio, and a driveway. ruclips.net/user/postUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX It has performed as expected on all surfaces. For larger areas like the decks and patios, I think I will be looking into a surface cleaner attachment to speed up the job, or at least make it a little easier. Hose and sprayer connections are tool-less, tight, and quick. I used the yellow nozzle on the concrete/brick surfaces, and the pressure was adequate for cleaning those surfaces.I am disappointed that these units are still being shipped with a nozzle storage holder that allows them to vibrate out of the holder way too easily and become lost, but I don't want to knock off a star for that reason. The functional part of the washer works very well, so I would recommend this product.
@@motorcarnut i just got my today but water spells all over but i just realize y put compressor oil stupid right what i should do now cleaning empty all oil and out 1040 or wht ty
Just got mine Yesterday can't wait to wash my cars and use a foam cannon, had 2 electric ones pumps went out, never again, gas is the way to go for pressure washers, more constant power and pressure 😎
That doesn't make any sense. All you do is switch to a different nozzle other than the black soap and when you spray a little soap comes out then stops, simple.
@@motorcarnut Hell I dunno man. I'm just relaying what I read in the manual. It said "detergent could become embedded in the surface" when using higher powered nozzles.
This looks almost identical (besides colors) to my Westinghouse 3200psi gas pressure washer. The only differences are the soap reservoir and the valve orientation at the rear where the hoses hook on. Mine has only lasted about 2 years before some internal clogging has occurred and now water spills into the soap dispenser and is pressurized enough to pop the lid off the soap reservoir…
Got mine for $399. First 2 days worked fine...last few started surging (not sure if that's normal) also the plastic line connected to the soap dispenser is clogged with water looks like the seal is stuck in the hole so water is overflowing out the dispenser box. Going to return and try again (no I didn't put any liquid in it).
I got one of these today. I was excited to try it out but am having problems with mine. It will start on full choke but will cut out on run. Oil type and amount is correct and I’m using ethanol free fuel. I’m reluctant to even check the carburetor because it’s a brand new power washer. I will likely return it.
I have the exact same one..hoping we can still power wash floor mats without shredding them. We just got ours 2 days ago..I know not to get mega close to them lol
@@motorcarnut They always tell me that when an item is already sale priced a coupon cant be used. One or the other, not both. So whats up with that??? I am an inside track club member also.
I need a washer that will work with 300-500 foot of water hose. Some can pump from a portable tank or 500 feet of 3/4” water hose. The pump on the one you’re testing does look like it is made from brass.
I’m not real impressed with Harbor Freight at the moment. Second time this has happened to me . I start researching one of there products in hopes to buy it and all of a sudden the price jumps up to as mush as the rest of the competition. I was going to buy this pressure washer but within a day of researching it jumps up to $449. Sorry Harbor Freight but I just purchased the Simpson Mega Shot with the Honda engine for the same price.
How do you like the Simpson? They are all the same price, but I actually see better reviews on the predator. I'm wondering if we're getting to the point where Harbor Freight quality is better than some of the name brands? I would trust the Honda engine more, but these pressure washers seem to have other problems to worry about.
you probably fixed yours by now but I had the same problem today and it ended up being the float needle valve was gunked up. I took it out and cleaned it and it starts right up now
How old is it? And what do you mean doesn’t start well? Is it hard to get it going? All depends if it’s still under warranty that’s why I ask how old it is.
Just used mine today. After 15 minutes of use I shut it down to move furniture. Would not start. Had to wait 30 minutes before it would start again. My boy bought a 4400psi. Had the same problem. His even had a backfire problem.
@@BillyBob-op6lg thats what i was thinking. There was alot of other pressure washers I found during my research. That looked about the same. So i just got that one curbside pickup form HD
Hello, I am actually watching your video since I want to get this same model. When cleaning the concrete, do you add any additive to the tank other that just the special detergent? Say Clorox? Thank you!
Actually . for the concrete unless its for disinfecting , just the pressure of the water should be all you need. The detergent tank is for laying the soap on at a low pressure. I'm not sure if you can use other cleaners in the tank, got to check owners manual.
Do you ever feel this 3200 psi could damage paint on a car or run the risk or ever want a lower pressure for car washing or is it pretty safe with common sense?
40 degrees. Most brands you the same colors for their nozzles. The pressure doesn’t change but the concentration of stream does. That’s the most important. You can have a 1200 psi washer and if you use the wrong tip, it will damage the paint as well.
I got this unit. Works great except while it’s running when I go to move it to a different spot it dies. Is this a new safety feature or is there a fault with the machine? Anybody know?
The numbers on the craftsman were not as good but like someone else said, who knows if the numbers are accurate. But the HF does have a Honda clone engine and I got it for a great price and it's a great machine I use it all the time.
@@motorcarnut was looking for a used one and I found it for 100 but it wouldn’t start so they gave it to me and I took the carburetor apart and the screw that has the hole was clogged up and now it works like new. It took me maybe 10 minutes to fix it.
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
Just a tip, before turning off idle it all the way down before turning off. Good habit for all engines. Its hard on them to go from running wide open to instantly shut off
Very true, thank you for that extra info!
I've used this sprayer several times now on brick pavers, a wood deck, patio, and a driveway. ruclips.net/user/postUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX It has performed as expected on all surfaces. For larger areas like the decks and patios, I think I will be looking into a surface cleaner attachment to speed up the job, or at least make it a little easier. Hose and sprayer connections are tool-less, tight, and quick. I used the yellow nozzle on the concrete/brick surfaces, and the pressure was adequate for cleaning those surfaces.I am disappointed that these units are still being shipped with a nozzle storage holder that allows them to vibrate out of the holder way too easily and become lost, but I don't want to knock off a star for that reason. The functional part of the washer works very well, so I would recommend this product.
Yes, they are great machines, mine is going strong with no problem at all.
I just got mine today for $369 also with coupons with tax it's almost $400. Hopefully, it'll do the jobs around the house. You got a great deal sir...
I know. I think you will like it, I love mine.
@@motorcarnut i just got my today but water spells all over but i just realize y put compressor oil stupid right what i should do now cleaning empty all oil and out 1040 or wht ty
Hopefully you didn’t ruin the engine with compressor oil. Yes flush out and use engine oil.
I buy one too today for $369
Good deal and great machine. Remember you have to fill it with oil Before using it.
3:25 DONT FORGET TO ADD OIL! Thank you for telling us this!!
No problem, it may be obvious to some but not to others and will destroy the engine and they won’t take it back.
Just got mine Yesterday can't wait to wash my cars and use a foam cannon, had 2 electric ones pumps went out, never again, gas is the way to go for pressure washers, more constant power and pressure 😎
Definitely gas powered.
@@motorcarnut hey boss mine makes a sputtering noise when running is that normal?
No should be smooth and powerful
@@motorcarnut it's brand new first time using it.. So should I return it?
I would definitely
Wow, this thing is $400 now! Fricken inflation is ridiculous!
Tell me about it
Bidenomics
@geo745don Lol
Everything I needed to know. thank you.
Sure no problem!
They actually recommend emptying the detergent tank and clearing the line if you're going to use other nozzles apart from the black one.
That doesn't make any sense. All you do is switch to a different nozzle other than the black soap and when you spray a little soap comes out then stops, simple.
@@motorcarnut Hell I dunno man. I'm just relaying what I read in the manual. It said "detergent could become embedded in the surface" when using higher powered nozzles.
Maybe just take care to spray it clear elsewhere before hitting the target surface after switching away from detergent.
I was thinking about the size is perfect for a trailer hitch basket and a small reel with 100 ft hose
It is
Sorry, but I’m new to using one. You didn’t specify in the video, once you start it, do you immediately switch from start to run?
Yes
This looks almost identical (besides colors) to my Westinghouse 3200psi gas pressure washer. The only differences are the soap reservoir and the valve orientation at the rear where the hoses hook on. Mine has only lasted about 2 years before some internal clogging has occurred and now water spills into the soap dispenser and is pressurized enough to pop the lid off the soap reservoir…
This uses a Honda engine, pretty much all parts are interchangeable.
@@motorcarnutHonda clone, but still very good motor!
@MrRunItUp I think so
Got mine for $399. First 2 days worked fine...last few started surging (not sure if that's normal) also the plastic line connected to the soap dispenser is clogged with water looks like the seal is stuck in the hole so water is overflowing out the dispenser box. Going to return and try again (no I didn't put any liquid in it).
Yes, bring it back sounds defective. Mine has no issues for over 2 years.
I got one of these today. I was excited to try it out but am having problems with mine. It will start on full choke but will cut out on run. Oil type and amount is correct and I’m using ethanol free fuel. I’m reluctant to even check the carburetor because it’s a brand new power washer. I will likely return it.
You probably got a defective one, it happens. Just a another one, mine stills works as new 2 years later
I have the exact same one..hoping we can still power wash floor mats without shredding them. We just got ours 2 days ago..I know not to get mega close to them lol
You can just keep the wand further away and use the widest nozzle and you'll be fine.
Are you sure you paid $260, new price? Harbor Freight has this for $369 on sale.
Yes, I’m an inner club member plus I had a coupon
@@motorcarnut what coupon plz share
I had a 30% off coupon I used plus it was on sale and I’m an inner member
@@motorcarnut They always tell me that when an item is already sale priced a coupon cant be used. One or the other, not both. So whats up with that??? I am an inside track club member also.
Don’t go to a normal one go to the big warehouse they have more options and are cheaper 😊
Do you think this would be able to do my semi truck?
Sure, no problem
Will it work with over 50 feet of hose?
If the pump isn’t made from brass then it’s junk.
Idk, I never used more than it came with
@@motorcarnut Sorry I meant the water inlet hose not the sprayer hose.
@Robert-ug8uu oh yes, I’m using 50 foot hose now.
I need a washer that will work with 300-500 foot of water hose.
Some can pump from a portable tank or 500 feet of 3/4” water hose.
I need a washer that will work with 300-500 foot of water hose.
Some can pump from a portable tank or 500 feet of 3/4” water hose.
The pump on the one you’re testing does look like it is made from brass.
I’m not real impressed with Harbor Freight at the moment. Second time this has happened to me . I start researching one of there products in hopes to buy it and all of a sudden the price jumps up to as mush as the rest of the competition. I was going to buy this pressure washer but within a day of researching it jumps up to $449. Sorry Harbor Freight but I just purchased the Simpson Mega Shot with the Honda engine for the same price.
I understand where you’re coming from. The HF does have a clone Honda engine as well. But with prices going up it gets hard to choose.
How do you like the Simpson? They are all the same price, but I actually see better reviews on the predator. I'm wondering if we're getting to the point where Harbor Freight quality is better than some of the name brands? I would trust the Honda engine more, but these pressure washers seem to have other problems to worry about.
@Soupy_loopy depends on the exact tool you’re talking about but like anything got to comparison shop
I cant start my pressure washer it has oil and fuel. Anyone have any idea why it wouldn’t start??
Plug fouled, make sure choke is on
you probably fixed yours by now but I had the same problem today and it ended up being the float needle valve was gunked up. I took it out and cleaned it and it starts right up now
Thanks for the info, maybe will help others
Used my power washer to kill lantern flies using dish soap on my tree.. it worked
Not a bad idea
@@motorcarnut I’ll let you know during the week if they come back
Hello, from Arizona here. For some reason my unit doesn’t start well with the choke on start. Premium gas and 10w-30 oil. Any thoughts?
How old is it? And what do you mean doesn’t start well? Is it hard to get it going? All depends if it’s still under warranty that’s why I ask how old it is.
Just used mine today. After 15 minutes of use I shut it down to move furniture. Would not start. Had to wait 30 minutes before it would start again. My boy bought a 4400psi. Had the same problem. His even had a backfire problem.
@chessiekid4018 maybe bad gas? If both were giving problems?
how did you get it for $260. its $430 at my store?
They put them on sale all the time where I live and I used a coupon to bring it down even more to $269
$369.00 Sonora Ca.....thats with coupon...what a great steal for this guy...congrats
@@4RFarmLife i ended up going with the ryobi 2900 psi 2.5 gpm for $330
@@supertitan21 more than likely this predator is exaggerating the pressure anyways
@@BillyBob-op6lg thats what i was thinking. There was alot of other pressure washers I found during my research. That looked about the same. So i just got that one curbside pickup form HD
Hello, I am actually watching your video since I want to get this same model. When cleaning the concrete, do you add any additive to the tank other that just the special detergent? Say Clorox? Thank you!
Actually . for the concrete unless its for disinfecting , just the pressure of the water should be all you need. The detergent tank is for laying the soap on at a low pressure. I'm not sure if you can use other cleaners in the tank, got to check owners manual.
@@motorcarnut
Roger that!
Truly appreciated.
Where do you turn the psi down on it at?
See what the manual says, I’m not sure, maybe you can’t, have to use a different nozzle I’m assuming.
Anyone recommend this unit for starting up an exterior painting business?
I have the machine for over a year and it’s been reliable and use it often.
Do you ever feel this 3200 psi could damage paint on a car or run the risk or ever want a lower pressure for car washing or is it pretty safe with common sense?
Perfectly safe with common sense. You can always hold the wand further away from the paint and use the proper nozzle, the white one.
@@motorcarnut any idea the angle of the white one I have a different brand. It’s still 3200 psi pressure right that doesn’t change
40 degrees. Most brands you the same colors for their nozzles. The pressure doesn’t change but the concentration of stream does. That’s the most important. You can have a 1200 psi washer and if you use the wrong tip, it will damage the paint as well.
Thanks very much buddy 🎉, very good, clear video with great instructions and demonstration. Appreciation for your video review ✨️.
Thank you! Appreciated! Still use it and have no issues.
Just got mine today and I’m excited shits cool
It's a decent machine, I use it a lot. Good luck with it.
I can get one for 300 with a coupon but cannot find it for 269
That’s not a bad price these days and it works great, just used mine again today, starts with one pull.
Do you think 280 for one is a good price?
Yes I do. It’s a great machine and I use it all the time.
Where did you find it for 280? Harbor freight wants 430.00
Offer up lol I ended up buying it haven’t used it too many times but the times I have I like it
You’re the man. Thanks.
Thanks bro!
@@motorcarnut Literally got me going in less than 10 minutes after watching this video. Beat flipping through a manual.
Awesome!
What kind of soap did you use ?
Karcher Pressure Washer Car Wash & Wax Cleaning Soap Concentrate - 1 Gallon a.co/d/0zbfxSA
@@motorcarnut thank you 👍
Seems like a good unit
So far so good, I use mine pretty often.
@@motorcarnut is it easy to load into the bed of a truck?
Has anyone ever tried to use it as a pressure washer business?
It’s not made for commercial use but for the money it’s a great unit.
Thank you for the fast response
You're welcome!
I got this unit. Works great except while it’s running when I go to move it to a different spot it dies. Is this a new safety feature or is there a fault with the machine? Anybody know?
No, it’s not supposed to do that. Make sure gas line is not kinked.
This seems like a good little machine. Like to see a comparison to a craftsman from like lowes.
The numbers on the craftsman were not as good but like someone else said, who knows if the numbers are accurate. But the HF does have a Honda clone engine and I got it for a great price and it's a great machine I use it all the time.
@@motorcarnut I am very late, but my craftsman just stopped working and I got this one. I will let you know how it goes if it still matters to yall.
@@dylanbehrends8932any update?
@Dylan Behrends any news??? Working good??
Dayum I payed 400 for mine at harbor freight
Prices go up on everything unfortunately
You should get a foam cannon lol
I like soaping up by hand to get all the areas, I haven't used a cannon yet though.
@@motorcarnut great investment you should look into it prob can get one for like $30 maybe even cheaper. High quality for no more than $100
Will do, Thanks!
Damn way more expensive now
I hear ya, what isn’t!
$260??? what? It's $449 on their site
Yep, that was a couple of years ago too
Man, that thing is $449 right now.
Wow, inflation is out of control
$287 display they have one more
That’s a great price for a 2023 model
Hows your predator doing , about to buy one i think
I used it about 6 times this year so far and it’s still working great.
@@motorcarnut thanks buying one this weekend
@E2DaG805 sure good luck and make sure you put the oil in it before you start it they come dry.
Not the best spray for foam get the chemical guys foam sprayer
No, it doesn’t replace foam sprayer’s, I agree
Got mine for free
Wow, how did you manage that?
@@motorcarnut was looking for a used one and I found it for 100 but it wouldn’t start so they gave it to me and I took the carburetor apart and the screw that has the hole was clogged up and now it works like new. It took me maybe 10 minutes to fix it.
Ha, good for you!! That’s great
This piece of gah bidge is now $450, not $260
It may be more expensive now, what isn't? But it's a decent machine, I have no problems with it.
Thank You For Your Video
Does Not Clean Properly Good,
2.8 GPM With Not Strong Power,
The 2.5 Ryoby Cleans And Do
Better Job Than This Machine.
Amén.
You’re welcome. Mine cleans perfectly fine maybe yours is defective?
You shouldn't be getting so close to your house sding or wood
No I know what you mean, it can do damage.
Where did you get it for $269?
Read comments, explained it already I’m a member and coupons on sale.