Это видео недоступно.
Сожалеем об этом.
Simple Automatic Plant Watering System || DIY
HTML-код
- Опубликовано: 27 июн 2020
- Learn to make a simple automatic plant watering system with easy to use plug and play wiring. No Arduino evolved. No Soldering Needed. Fun project for both gardeners and electronics beginners alike. Cost less then $7 to make the entire project. Project item list is below:
5V Submersible Pump:
www.ebay.com/p...
5V relay module:
www.ebay.com/i...
Soil Sensor:
www.ebay.com/i...
Completed my 1st year project thanks to you. Cheers sir
Moisture sensors like the one shown will corrode away to nothing in a few months in moist soil. The fully insulated capacitive sensors cost a dollar more but they last.
Great work man! Keep projects like this coming...
Nice video! And a cool idea. I have a 4x 5V relay and you have encouraged me to do this 4 times over for a few potted indoor plants. Thank you for the content!
I'm thinking of doing a entire automation series that doesn't use arduino/raspberry pi
you prolly dont give a damn but does anybody know of a trick to log back into an instagram account..?
I stupidly lost the account password. I love any tips you can offer me!
@Chandler Karter instablaster :)
@Malakai Raymond I really appreciate your reply. I found the site thru google and Im in the hacking process atm.
Seems to take a while so I will reply here later with my results.
@Malakai Raymond It did the trick and I actually got access to my account again. I am so happy!
Thank you so much you saved my ass!
Found you on the Vivosun fb post 💪thanks for sharing
Thanks for the support!
Nice nice
What a idea❤
Thanks duct tape mechanic
is it possible to just use the "low trigger" types of relay module instead of the "high trigger"???
This will work unless the end of the tube (in the pot) is below the surface of the water == water will tend to balance its height/level in both pots.
Thank you so much door the video.. Just bought it so yet wasn't sure how to put it all together.. The last step wasn't completely clear to me.. When.using the power bank all I have is one red that is.not yet wires, and one black the isn't wired.. Is it only one positive and one negative wires that goes to the power bank.? Do you happen to have drawing of it all.?
If you could figure out a way to auto PH balance the water too that would be sweet.
Cool idea !
I'm new to electronics. I reproduced your exact setup but it's not working. I did a bit of debugging and the pump works well if I connect the usb directly to it. After a while, I realized my relay is 12v. Would that explain why nothing happens when I put everything together and plug it in ? Ah and also, thx for this video, I really like it.
Yes that would explain it. You need a 5v relay.
Has any done this with a capacitive sensor. All the ones I see you have to use Arduino with the capacitive sensor but this setup is much simpler and I want to use the capacitive sensor. Thanks in advance.
Thanks for the video but the sensor just corrodes as it is DC so will not last long please look at Capacitive sensors
Hey ductape mechanic,
I have a question, i made one but mine is werking the other way around. So of the meter is in contact with water, it starts the pump. Do you have any ideas in why this is happening?
Hey! Yes take a look out how the pump is wired into the relay. Is it in the NO or NC position? Also check to see if the relay jumper is set to be triggered at a high signal.
Why does my dc water pumps does not stop automatically
Hi! I have a question. Why does my pump keep on watering even though my sensor detects the water.
Also can you please give a blueprint on this.
P. S.Thank you for the great content!
Thank you for watching. Is it possible you have ur relay set for "low trigger". Make sure the relay jumper is set to "high trigger". I would check that first. Then make sure u are getting power to the sensor PCB (I believe an LED should be lit). Hope this helps.
hello, can I ask what type of jumper cables, is it 100mm or 200mm? Thank you
Shouldn't really matter I'd go with the longer wire
could you send photo with all conections? my pump is working all the time :D
Have you found a solution? I have the same problem
@@petlifesaver i don't :/
i'm a complete electronic noob, so a larger relay to power a larger pump?
If you have a larger pump that draws more current then the specifications of this relay (I believe they can handle up to 10 amps) then you would need a larger relay (maybe even a contactor if you are dealing with loads greater then 30 amps or so)
@@DuctTapeMechanic thnx bro, much apreciated
I buy IT with Batterie but this System use to much Power and The battery is empty after one day (The pump dont Run in this time)
bro i am confused make a clear video about everystep again please!
i tried this project but i am not getting correctly because some confusing
have you figured it out? mine doest work too
What happens when the water reservoir runs dry?
It's more for if your going on vacation or if you plan on refreshing the reservoir once a week
@@DuctTapeMechanic Is there a way to disconnect the battery when there's no more water? Like a switch?
What is Final set point of moisture value?
i wana know too
Bro can u send the circuit diagram of the project
Can i use other 5v Submersible pump?
Yes shouldn't be a problem
@@DuctTapeMechanic its not working in a usb cable there's no light in Relay module
@@DuctTapeMechanic what should i do
why not normal speed video?
Hey, can we use a cooler pump in this 220V
Please tell
I don't think that relay is rated at 220 volts
@@DuctTapeMechanic ok
Please give the circuit diagram
Code please
Sell me one on eBay!
Too fast.
You are not to familiar with the term simple. It's sad how you waste people's time because you can't understand simple things.
So sad
Nice nice