@rr8195 You can do that 2 ways. One is by using the EQ to notch out that very high end. two is the use the Global EQ settings in the System "Input" section. You have many EQ settings there.
Cool deal!!! when I was tryin to decide between the gt10 and pod I watched these videos and they didn't make much sense, now that I own the gt10 and have had a few months to tweek around with it these videos make tons of more sense to me. Thanx for the time you take to make these videos, they help a lot
AT LAST.....now i will go ahead and buy this thing. I like music like Angels and Airwaves and U2 and wanted to make sure that smooth transition between delay and no delay and general smooth control of other effects was possible. i messed around with the one at my local store and just couldnt figure out how to do it. i was about to buy the VG-99. You just saved me alot of money mate. THANK YOU.
@musikeroz73 You have to press the Master FX button to turn on an assign. Also when using CTL1 for an assign other than chorus(which is the default) you must first go into the pedal assign mode and turn CTL1 to off.
@VegasGuitarPlayer Yes I think you can. Just go into the assigns and find the preamp gain control and assign a minimum and maximum amount to the pedal. It should work.
We have a winner!! Thank you... really, really helpful. I've even managed to program a simultaneous 'reverse swell' on the expression pedal to counter the increase in volume as the gain increases.
Thanks for all the tips and info, Glenn. I just swapped my old GNX4 in for a GT-10, and I absolutely LOVE it. Sooo, much more capable piece of equipment. I have the GT-10 with the FS-6 dual footswitch for CTRL 3 and 4, with a TC Electronics Nova Delay running through the effects loop of the unit. I took your suggestion and use the expression pedal for gain control and other things, and have a seperate volume pedal on the board. Lovin' it!!
Yes if you use the amp models they are "fizzy". That's why I don't use them. I use either real distortion pedals OR I only use the Overdrive stomps in the GT-10 and POD HD500, depending on what rig I am using that night. I have four complete different rigs. The best & biggest is 2 Marshall heads and 2 4x12cabs. The smallest is just the POD HD400 right into the PA direct.
@rr8195 By using the EQ settings as I described to you. And also you can try the Resonator effect in wither FX1 or FX2. This also is sort of an overall EQ
@Saved4Life1550 Press the write button and save it to presets starting at U-01. You can't save to the P-01 settings because that is the factory presets.
Well yes & no. You CAN save effects and recall them easily and apply them to other patches. For example, you can set a chorus sound like you want it and you can save that setting. Then when you switch to another preset and you want a chorus you can turn on the chorus and using the "User Settings" you can apply your saved version of that chorus. You can do this with all of the effects and even the amps in the GT-100.
@glinder5150 Yes, try the Tone Modify effect on either FX1 or FX2. This is an effect that no one talks about but I use it on every single patch. It really adds life to the sound.
You are totally the best tutorial-guy on RUclips, and an amazing guitar player to. Keep up the good work. I have a GT-10. Bought it because I saw your videos, and I am still learning. Can't wait to check out your next tip. Thanks :-)
thanks Glenn your help is much appreciated and keep up the good work, because people like you are hard to come by who give up there time to help others improve at a much faster rate than was ever thought possible. Cheers,, Neil
Yes there is a way to get that sound. I have a patch in my bundle called Ice Crystals that uses the dual delay, hall reverb and chorus effect. It's a pretty cool sounding patch.
@extremevideopro You totally rock Glenn. I'm learning a few pointers here and there from the knowledge and experience you share. Not only that buy you are a very good singer and guitarist. Thanks a bunch and keep rockin!!! Joe...
Thanks for the quick reply Glenn - my GT10 should be coming in the post today :) Keep up the good work and thanks for the hard work you do to educate us all.
@extremevideopro Oh, I just figured it out. Thanks. I had my setting in the Preamp channel set to "dynamics" which is why it's switching between A and B. Thanks. Rock on!!
wow man ive been watchin ur vids for a while now and i never knew that you played praise and worship. i am also the lead guitarist for a praise and worship team in northern Arkansas. Rock On!! lolz...
I'm in a cover band and I've written a patch for each song...this will help a lot! BTW, Traynor owes you a commission, I bought a K4 yesterday. Thanks for the recommendationS and advice! YOU DA MAN!!!
@glinder5150 Yes normally if you are going to use distortion from the GT-10 you will want to have your amp on a clean channel. Try that and you should be OK.
If you hook your GT-10 up to your computer using the USB then yes you can. Using the USB connection your GT-10 becomes your sound card so all audio from your computer goes to the GT-10 so you can use Media player or whatever you use to listen to music on your computer and it will come through the GT-10 and you can play along with it that way. That's the only way AFAIK
@extremevideopro Thanks man! I got the ME-70 and I am very pleased!!! my only gripe about the pedal is that switching between sounds and patches will take some getting used to, but boss makes a great pedal!
Yeah, I do this do for some of my patches, typically my standard dirty rhythm tone patches. Give it enough gain all the way up to play some lead, and clean enough all the way back to give you a cleanish strummable tone under vocals. hugely important for controlling volume, much more convenient than adjusting the guitar volume all the time.
@extremevideopro Both... I run direct playing with the praise and worship team at my church, but I also play with a Christian contemporary band out of Oklahoma City, and I run through either a rackmount power amp and 4x12 enclosure, or my Randall combo, depending on the venue we're playing. The fexibility of this unit is perfect for me.
Glen you are amazing dude... very helpful!!! If you could do a full tutorial on how to master the use of gt-10 it would be great man!!! keep rocking ;)
@MattWilson02 I use the four cable method also through my mesa boogie head and it sounds good, I can get a pretty good sound though using it direct, but it does take a lot of tweeking, but running direct to a pa system as long as my output select is set to a line out instead of the amp setting it sounds really good
So there is no "Set" of FX can can be added all at once. It's all done on a patch by patch basis. But there is no reason why you can have say 20 patches saved with certain effects and then 20 more patches saved with different effects.
Thanks for your answer ! But the rocktron velocity 300 is a guitar power amp and i think i can't put it in the fx loop !! no ? Perhaps i have do a bad calibration of my input guitar in the gt-10 ? or another think, so i test a lot of solution but never find the good ! sniff
Man! I just spent 3 hours trying to figure this out!!! Not 3 minutes in and you just had to say 1 word that made a light in my head go on so I hit pause and VOALAA! I almost just guessed just because of 1 word and visual moment in the clip! Thanks, were was this 3 hours ago?
Hello Glenn, great video!!!!!!!!! I have a Marshall Jcm 2000 tsl 100 . I have the Boss gt-10 and I would like to know about the 4 method cable. I do not think it is anything I can do, but maybe you can help me. I do not think that my marshall has a MIDI.Another question that I have is the FX LOOP, is this FX LOOP serial or Parallel? I think that I have both (Serial and Parallel), but I prefer i you can tell me which one I have and what position do I have to put. Let me know and thank you. Inaki
The grass 10 does a nice job of loosely emulating guitarists sounds eg. erupting however can more solid presets be dialed in? Perhaps an online community that shows the exact settings Eddie used and how to program them I.
Would I be correct in assuming that if a guy wanted to still have volume control on the floor instead of having to use the volume knobs on the guitar, he could just add a stand alone volume pedal into the chain?
Man that's good stuff so you played right into that amp on a clean channel then used the od in the gt10? have you ever had the problem I have with these cosm multi fx where you get what I would call digital fizz usually as you are muting the strings especially on high gain stuff and have you found a way to fix that?
Thanks for prompt reply! If I assign one delay setting to CTRL 1 and another delay setting to CTRL2 and press CTRL2, doesn't that change the "state" that CTRL 1 is in?
@extremevideopro Hi again, by the way...I tried it and it's great...but my only problem is when I pick my guitar strings harder, my overdrive goes out. Is there some sort of a sensitivity adjustment that will accomodate for my harder strumming? Thanks again.
Thank You for the Tutorial. it really helped me with my GT-10. But how can I increase the volume of my clean? The overall sound of clean is so small and theres a big difference when i switch from clean to od on the pedal
Hi Glenn, Is there a way to set two different delay settings in one patch? Also, I have a problem when I engage the wah, the volume is at max. How can I resolve this situation. Thanks for being my best resource for GT10 issues!!!
@extremevideopro still tryin to figure out the proper way to go about getting the flat tin type sound out of alot of the distortions on the gt10 or rather how to get the tone back. seems like the distortions have great crunch but seems to make the tone flat any suggestions
Glen, always found your videos very constructive and useful and your playing is awesome. I have a question for you about the GT10 and that is can I achieve a shimmer effect like Edge from U2 with the GT10 if so how? do I need to add a Shimmer effect via a Verbzilla which I also have. I have a Marshall MG100dfx & a small VOX combo amp there is no send /return on these amps can I achieve it via the external foot pedal send/return hellllllllllllllllpppppppppp
Hi Glenn, I have a boss gt-10 and just purchased a fender 1x12 40w hot rod deluxe. What cables do you recommend, and how exactly do I set it up. I apologize I'm newer to the expression world :) THANK!
Im not sure what my issue is it could be the fight between the gain on the amp and the gain on the pedal system but theres a few distortions im having trouble setting up when i go through them i get alot of noise when not playing. Should i turn down the amp gain all the way? I have a line 6 212 spider Any info you guys can give on how i should go about this would be great thanks for your time
@extremevideopro so what you have dont use batteries??? by the way you did a great job showing your setup in the gt-10 and thanks again for sharing your patches, i have one question... how did you recorded it???
hi glenn...ive got an issue with my gt-10...im trying to use it in manual mode and i am ok with programmin it but i cant understand why it wont let me store fx1 as c# harmony and fx2 as f# harmony..?...when i save it as such they both revert to 1 key?....hope you can help...your demo's are excellent and most helpfull...regards jud.
Hi Mr Gleen I want to know if Do you think that is good idea mix the GT10 with a pedal distortion like Metal Core or Digitech Metal Master....or is a waste of money buying other pedal. I use the GT10 with the four cable method and sound really good. But I want to reach my own sound, and i like strong Metal distortion, and I want to know if It was a good idea mix a distortion pedal with Boss gt 10.
Is there a way to set it up on the GT-10 to have Channel A do exactly what you've shown here with the gain control assigned to the EXP Pedal 1, but when you switch to Channel B, you can have EXP Pedal come on with a Wah assigned to it instead of the gain control?
hi glen, is it possible to use the expression pedal as a volume control, but when ctl1 is pressed (which is assigned to wah) for it then to change the frequency sweep?
HI GLEN,,, HAD A QUESTION HOPEFULLY YOU CAN HELP ME, I MUST OF DISSABLED MY VOLUME PEDAL,ALREADY TRIED THE PEDAL VOL.CALIBRATION & STILL DONT WORK, ANY IDEAS WAT COULD OF HAPPEND? THANX GLEN, JUST DIDN'T WANT TO BACK TO ORIGIONAL FACTORY PRESETS,,AND ERASING MY ORIGIONAL SETTINGS......THANKS
Glenn, I received my K4 and I'm having trouble keeping the harsh high end out of the the hi freq drivers. I was wondering if you cut the treble at the amp or perhaps eq everything with the GT and cut the 2k or so. I'm using a Luke Music Man with an active EMG 85 at the bridge and EMG single coils mid & neck. I'm staring to wonder whether active pups are not a good match with the GT. Suggestions? THANKS!
Another question, I was trying out the looper then I thought of recording it via USB like my other recordings, then I listened to what I've record. when I play over my loops, the only thing that is recorded is the one I'm actually playing, the loops are not recorded. Is there a way I can record my loops aside from manually copying and pasting my loops on a track?
Hey there, Glen... Can you tell me if this effect can be done using the Preamp instead of the OD function? I've followed your instruction and works well if using the OD...but not for the Preamp. Thanks.
I must say braddah, your demos were the deciding factor for buying my GT-10 and my JC-120. They are a match made in heaven. Thanks for the vids.
@rr8195 You can do that 2 ways. One is by using the EQ to notch out that very high end. two is the use the Global EQ settings in the System "Input" section. You have many EQ settings there.
Thanks Glenn. It was time for all of us in the other side to see you make new things with the gt10. I am a fan of yours.
Cool deal!!! when I was tryin to decide between the gt10 and pod I watched these videos and they didn't make much sense, now that I own the gt10 and have had a few months to tweek around with it these videos make tons of more sense to me. Thanx for the time you take to make these videos, they help a lot
Great vid. Don't think I ever would have figured that one out. Please keep the GT-10 tips & trick coming. Thank alot.
AT LAST.....now i will go ahead and buy this thing. I like music like Angels and Airwaves and U2 and wanted to make sure that smooth transition between delay and no delay and general smooth control of other effects was possible. i messed around with the one at my local store and just couldnt figure out how to do it. i was about to buy the VG-99. You just saved me alot of money mate. THANK YOU.
@musikeroz73 You have to press the Master FX button to turn on an assign. Also when using CTL1 for an assign other than chorus(which is the default) you must first go into the pedal assign mode and turn CTL1 to off.
@VegasGuitarPlayer Yes I think you can. Just go into the assigns and find the preamp gain control and assign a minimum and maximum amount to the pedal. It should work.
Glenn DeLaune lesson pleeeese. Im A quick study, turn on the cam and start the buttons pressing:)
man Boss should definitely hire you, you make the best demonstration videos!
We have a winner!! Thank you... really, really helpful. I've even managed to program a simultaneous 'reverse swell' on the expression pedal to counter the increase in volume as the gain increases.
Thanks for all the tips and info, Glenn. I just swapped my old GNX4 in for a GT-10, and I absolutely LOVE it. Sooo, much more capable piece of equipment. I have the GT-10 with the FS-6 dual footswitch for CTRL 3 and 4, with a TC Electronics Nova Delay running through the effects loop of the unit. I took your suggestion and use the expression pedal for gain control and other things, and have a seperate volume pedal on the board. Lovin' it!!
Yes if you use the amp models they are "fizzy". That's why I don't use them. I use either real distortion pedals OR I only use the Overdrive stomps in the GT-10 and POD HD500, depending on what rig I am using that night. I have four complete different rigs. The best & biggest is 2 Marshall heads and 2 4x12cabs. The smallest is just the POD HD400 right into the PA direct.
Yes, you could try putting the Nova drive in the FX loop of the Gt-8
@rr8195 By using the EQ settings as I described to you. And also you can try the Resonator effect in wither FX1 or FX2. This also is sort of an overall EQ
@Saved4Life1550 Press the write button and save it to presets starting at U-01. You can't save to the P-01 settings because that is the factory presets.
Well yes & no. You CAN save effects and recall them easily and apply them to other patches. For example, you can set a chorus sound like you want it and you can save that setting. Then when you switch to another preset and you want a chorus you can turn on the chorus and using the "User Settings" you can apply your saved version of that chorus. You can do this with all of the effects and even the amps in the GT-100.
@glinder5150 Yes, try the Tone Modify effect on either FX1 or FX2. This is an effect that no one talks about but I use it on every single patch. It really adds life to the sound.
You are totally the best tutorial-guy on RUclips, and an amazing guitar player to. Keep up the good work. I have a GT-10. Bought it because I saw your videos, and I am still learning. Can't wait to check out your next tip. Thanks :-)
thanks Glenn your help is much appreciated and keep up the good work, because people like you are hard to come by who give up there time to help others improve at a much faster rate than was ever thought possible. Cheers,,
Neil
Yes there is a way to get that sound. I have a patch in my bundle called Ice Crystals that uses the dual delay, hall reverb and chorus effect. It's a pretty cool sounding patch.
@extremevideopro You totally rock Glenn. I'm learning a few pointers here and there from the knowledge and experience you share. Not only that buy you are a very good singer and guitarist. Thanks a bunch and keep rockin!!! Joe...
Yes i think so, that would be in the pedal bend settings.
Nice demonstration man, you are really good to show how its done. Great job on the trick :D
I wish I had the answer. It should work if you go MIDI out of the GT into the MIDI in of the Nova.
Thanks for the quick reply Glenn - my GT10 should be coming in the post today :)
Keep up the good work and thanks for the hard work you do to educate us all.
@extremevideopro Oh, I just figured it out. Thanks. I had my setting in the Preamp channel set to "dynamics" which is why it's switching between A and B. Thanks. Rock on!!
Thank you. I use Dunlop Clear D Large
@glinder5150 Yes it does have that effect.
Those MG's are pretty good. I think they sound good all on their own. I would put the GT-10 in the FX loop of the amp.
wow man ive been watchin ur vids for a while now and i never knew that you played praise and worship. i am also the lead guitarist for a praise and worship team in northern Arkansas. Rock On!! lolz...
@extremevideopro thanks for the quick response (time zone difference helps that ;) will get searching now!
I'm in a cover band and I've written a patch for each song...this will help a lot! BTW, Traynor owes you a commission, I bought a K4 yesterday. Thanks for the recommendationS and advice! YOU DA MAN!!!
The GT-10 does not allow you to save your manual mode setting on a per patch basis. The GT-100 however DOES allow this function.
You should try going into the FX loop of your amp instead of going in the front input.
@glinder5150 Yes normally if you are going to use distortion from the GT-10 you will want to have your amp on a clean channel. Try that and you should be OK.
If you hook your GT-10 up to your computer using the USB then yes you can. Using the USB connection your GT-10 becomes your sound card so all audio from your computer goes to the GT-10 so you can use Media player or whatever you use to listen to music on your computer and it will come through the GT-10 and you can play along with it that way. That's the only way AFAIK
Hmmm, that's good question Tay, I'm not sure but I can check.
Yes you can and i think the setting would be momentary.
@extremevideopro Thanks man! I got the ME-70 and I am very pleased!!! my only gripe about the pedal is that switching between sounds and patches will take some getting used to, but boss makes a great pedal!
Yeah, I do this do for some of my patches, typically my standard dirty rhythm tone patches. Give it enough gain all the way up to play some lead, and clean enough all the way back to give you a cleanish strummable tone under vocals.
hugely important for controlling volume, much more convenient than adjusting the guitar volume all the time.
great and very usefull explanation Glenn !
grtz from Belgium
You are very talented and professional...really....
Excellent Glenn, Il be using that tip!!
Thanks so much Steve.
Thank you
Fantastic tutorial, well done! Great playing style as well!
@extremevideopro Both... I run direct playing with the praise and worship team at my church, but I also play with a Christian contemporary band out of Oklahoma City, and I run through either a rackmount power amp and 4x12 enclosure, or my Randall combo, depending on the venue we're playing. The fexibility of this unit is perfect for me.
Glen you are amazing dude... very helpful!!! If you could do a full tutorial on how to master the use of gt-10 it would be great man!!! keep rocking ;)
dude it sounded amazing on the recording!
I have had little luck adding this pedal into the fx loop. That would be a tutorial I’d be all over:)
man, thx a lot. these vids are really great and they help me much !
You could go either way but I would first try going straight into the front input of the Marshall. What model Marshall are you getting??
@MattWilson02 I use the four cable method also through my mesa boogie head and it sounds good, I can get a pretty good sound though using it direct, but it does take a lot of tweeking, but running direct to a pa system as long as my output select is set to a line out instead of the amp setting it sounds really good
Amazing tutorial, because this help me to program other effects.
great stuff, Glenn - BOSS should hire you(if they already haven't).
So there is no "Set" of FX can can be added all at once. It's all done on a patch by patch basis. But there is no reason why you can have say 20 patches saved with certain effects and then 20 more patches saved with different effects.
Nice thanks ..sounds very nice
Thanks for your answer ! But the rocktron velocity 300 is a guitar power amp and i think i can't put it in the fx loop !! no ? Perhaps i have do a bad calibration of my input guitar in the gt-10 ? or another think, so i test a lot of solution but never find the good ! sniff
Man! I just spent 3 hours trying to figure this out!!! Not 3 minutes in and you just had to say 1 word that made a light in my head go on so I hit pause and VOALAA! I almost just guessed just because of 1 word and visual moment in the clip! Thanks, were was this 3 hours ago?
@extremevideopro, Damn, didn't think so lol! Thanks for the reply!
Hello Glenn, great video!!!!!!!!! I have a Marshall Jcm 2000 tsl 100 . I have the Boss gt-10 and I would like to know about the 4 method cable. I do not think it is anything I can do, but maybe you can help me. I do not think that my marshall has a MIDI.Another question that I have is the FX LOOP, is this FX LOOP serial or Parallel? I think that I have both (Serial and Parallel), but I prefer i you can tell me which one I have and what position do I have to put. Let me know and thank you.
Inaki
The grass 10 does a nice job of loosely emulating guitarists sounds eg. erupting however can more solid presets be dialed in? Perhaps an online community that shows the exact settings Eddie used and how to program them I.
Thanks for doing these videos.
Killer trick man! Thanks.
Would I be correct in assuming that if a guy wanted to still have volume control on the floor instead of having to use the volume knobs on the guitar, he could just add a stand alone volume pedal into the chain?
OK great, I'm glad it helped out. Now go practice, practice, practice!!!
Another great video clean! Great work.
Question? Is there a tremendous volume increase using this method? Also
Man that's good stuff so you played right into that amp on a clean channel then used the od in the gt10? have you ever had the problem I have with these cosm multi fx where you get what I would call digital fizz usually as you are muting the strings especially on high gain stuff and have you found a way to fix that?
Thanks for prompt reply! If I assign one delay setting to CTRL 1 and another delay setting to CTRL2 and press CTRL2, doesn't that change the "state" that CTRL 1 is in?
@extremevideopro Hi again, by the way...I tried it and it's great...but my only problem is when I pick my guitar strings harder, my overdrive goes out. Is there some sort of a sensitivity adjustment that will accomodate for my harder strumming? Thanks again.
Do you have a Line 6 POD X3 Live?? can you make some video explanation for it? Thanks for all your Lessons!
Thank You for the Tutorial. it really helped me with my GT-10. But how can I increase the volume of my clean? The overall sound of clean is so small and theres a big difference when i switch from clean to od on the pedal
Hi Glenn, Is there a way to set two different delay settings in one patch? Also, I have a problem when I engage the wah, the volume is at max. How can I resolve this situation.
Thanks for being my best resource for GT10 issues!!!
@Saved4Life1550 Yes
@extremevideopro still tryin to figure out the proper way to go about getting the flat tin type sound out of alot of the distortions on the gt10 or rather how to get the tone back. seems like the distortions have great crunch but seems to make the tone flat any suggestions
i got the gt 10b but your tutorial is helpful! thank you :)
Glen, always found your videos very constructive and useful and your playing is awesome.
I have a question for you about the GT10 and that is can I achieve a shimmer effect like Edge from U2 with the GT10 if so how? do I need to add a Shimmer effect via a Verbzilla which I also have. I have a Marshall MG100dfx & a small VOX combo amp there is no send /return on these amps can I achieve it via the external foot pedal send/return hellllllllllllllllpppppppppp
Hi Glenn,
I have a boss gt-10 and just purchased a fender 1x12 40w hot rod deluxe. What cables do you recommend, and how exactly do I set it up. I apologize I'm newer to the expression world :)
THANK!
Can you also program the expression pedal to add the feedback of the delay? thanks
should be noted if you want to go from clean to distortion use the blues od for distortion.
Im not sure what my issue is it could be the fight between the gain on the amp and the gain on the pedal system but theres a few distortions im having trouble setting up when i go through them i get alot of noise when not playing. Should i turn down the amp gain all the way? I have a line 6 212 spider Any info you guys can give on how i should go about this would be great thanks for your time
@extremevideopro so what you have dont use batteries??? by the way you did a great job showing your setup in the gt-10 and thanks again for sharing your patches, i have one question... how did you recorded it???
Nice this is awesome Glenn! Just one question though do you know if this is possible with the POD X3 Live?
hi glenn...ive got an issue with my gt-10...im trying to use it in manual mode and i am ok with programmin it but i cant understand why it wont let me store fx1 as c# harmony and fx2 as f# harmony..?...when i save it as such they both revert to 1 key?....hope you can help...your demo's are excellent and most helpfull...regards jud.
Hey duds? I have a question?
How to save permanent the effects dat u creat?
quesiton about this, can you program this to one pedal and then for another pedal have the exp ped control the wah etc? make sense
Nice ! You lighting me
Hi Mr Gleen I want to know if Do you think that is good idea mix the GT10 with a pedal distortion like Metal Core or Digitech Metal Master....or is a waste of money buying other pedal.
I use the GT10 with the four cable method and sound really good.
But I want to reach my own sound, and i like strong Metal distortion, and I want to know if It was a good idea mix a distortion pedal with Boss gt 10.
Hi Glen, Is there a way to set exp pedal in GT 10 Bends the harmony between a fourth up (toe up) and a fifth up (toe down) above the input note ?
Is there a way to set it up on the GT-10 to have Channel A do exactly what you've shown here with the gain control assigned to the EXP Pedal 1, but when you switch to Channel B, you can have EXP Pedal come on with a Wah assigned to it instead of the gain control?
hey Glenn, which output select are you using? I tryied all of them im My Marshall VS100 Input, and the only one that i liked was the line/phones.
Did you try the different output modes? Try scrolling through them until you find one that sounds good and tweak your patches if necessary.
Love this stuff. Thanks Glenn!
hi glen, is it possible to use the expression pedal as a volume control, but when ctl1 is pressed (which is assigned to wah) for it then to change the frequency sweep?
I love the tutorials ... Could you doa tutorial dialing in the Blackmore tone (ish ..) using the BOSS GT 10 ..;-) ?
HI GLEN,,, HAD A QUESTION HOPEFULLY YOU CAN HELP ME, I MUST OF DISSABLED MY VOLUME PEDAL,ALREADY TRIED THE PEDAL VOL.CALIBRATION & STILL DONT WORK, ANY IDEAS WAT COULD OF HAPPEND? THANX GLEN, JUST DIDN'T WANT TO BACK TO ORIGIONAL FACTORY PRESETS,,AND ERASING MY ORIGIONAL SETTINGS......THANKS
Glenn, I received my K4 and I'm having trouble keeping the harsh high end out of the the hi freq drivers. I was wondering if you cut the treble at the amp or perhaps eq everything with the GT and cut the 2k or so. I'm using a Luke Music Man with an active EMG 85 at the bridge and EMG single coils mid & neck. I'm staring to wonder whether active pups are not a good match with the GT.
Suggestions? THANKS!
Another question, I was trying out the looper then I thought of recording it via USB like my other recordings, then I listened to what I've record. when I play over my loops, the only thing that is recorded is the one I'm actually playing, the loops are not recorded. Is there a way I can record my loops aside from manually copying and pasting my loops on a track?
@extremevideopro i already have no reverb on either my amp or the gt 10
Hey there, Glen... Can you tell me if this effect can be done using the Preamp instead of the OD function? I've followed your instruction and works well if using the OD...but not for the Preamp. Thanks.