Hello, good video, I have a problem, with Powersoft K20 it was working normally and I got an "error 6300" message on channel 1, what could be the cause and its possible solution?
@@mastercell14 In my Q3002 they are 1800uf 100V x14 of them. If replacing with cheap components then take 2200 if they fit. Some of the newer components are smaller than the old capacitors in the earlier Powersoft series. On the older Powersoft amps you can now fit bigger value capacitors or smaller ones than the originals with the same value. Giving either more air flow and more spacing from hotter parts of the board or a slightly larger value in capacitance. When servicing older amps always check all of the capacitors value and esr. I just repaired c55 in my amp. it was short blowing d5 and r42 i think. There is a part of this video where he is working next to the big capacitor bank and those caps are 680uf 250V Also.. TAKE THE FRONT PANEL OFF AND CLEAN ALL THE DUST OUT OF THE FILTER! oops caps lock,...
Good Job My Friend. Dear friend which Mosfet is better for 192KHZ Frequency ,Powersoft used this Mosfet Which you are Show in this video "FDH45N50F" . this mosfet is too slow according to the [ td(on), tr, td(off), tf ].
Mỏng dính size 1u vậy mà 18kw 2 kênh. Thật quá khủng.
Nếu không có đầu ra thì nên kiểm tra cái nào?
xem nh video của ad mới biết powersoft ko bền như lời đồn của các video quảng cáo
em sai rồi. Đồ điện tử nào sài vĩnh viễn em.
Great job. Do more videos like this.
Your DIN mounted watt meter it's not working properly. 220V x 1.6A =352W not 176.
Mạch class d chạy motfet loại mã số nào tốt ạ
100n50
@@76139tins😮😮 for power supply or for output 😮😮
Hello, good video, I have a problem, with Powersoft K20 it was working normally and I got an "error 6300" message on channel 1, what could be the cause and its possible solution?
Cara vc teria o ci que marca 611 para venda
Alguém pode mim falar estou precisando do ci que marca 611 -150 que vem Power sorft m50
Lo tienes el service manual circuito esquematico.
friend of what value are the filters of the power source of that amplifier
22uH
@@76139tins Greetings friend, not the coil, the source capacitors, how many uf are they?
@@mastercell14 In my Q3002 they are 1800uf 100V x14 of them. If replacing with cheap components then take 2200 if they fit. Some of the newer components are smaller than the old capacitors in the earlier Powersoft series. On the older Powersoft amps you can now fit bigger value capacitors or smaller ones than the originals with the same value. Giving either more air flow and more spacing from hotter parts of the board or a slightly larger value in capacitance. When servicing older amps always check all of the capacitors value and esr. I just repaired c55 in my amp. it was short blowing d5 and r42 i think.
There is a part of this video where he is working next to the big capacitor bank and those caps are 680uf 250V
Also.. TAKE THE FRONT PANEL OFF AND CLEAN ALL THE DUST OUT OF THE FILTER! oops caps lock,...
@@izzzzzz6 excelente amigo por esa gran explicacion tan valiosa
@@76139tins gracias amigo
Good Job My Friend. Dear friend which Mosfet is better for 192KHZ Frequency ,Powersoft used this Mosfet Which you are Show in this video "FDH45N50F" . this mosfet is too slow according to the [ td(on), tr, td(off), tf ].
You know power soft used which mosfet
@@shyamsharmas-invomahamai2552 exactly I don't know , I just see in this video which I've mentioned above