Thank you so much!!!!! Please use the sound if you can next time and explain while you doing it. It will help student a lot. Anyway thank you again!!!!!! :)
@@gadegroof if you please share me the matlab file that you have implemented recently . My email address is “qasimsaleem1988@yahoo.com”. I’ll highly appreciate your cooperation.
Could you share how did you get the values of the integrator, capacitor, inductor? Why did you change the value of the sample time of the discharging PI?
Hello sir @Naki GÜLER i want to know how to switch from Constant current to constant voltage mode at 80% SOC . It should sense automatically and enter into CV mode from CC mode. I have seen that you had changed the value manually i want to done automatically.
Sir, How do you calculate the inductance of converter and the DC Link in front of the load. and where is there not a need to put a Capacitor after the inductor for limiting the voltage variation. What is the load current for this circuit, Iref or Ibat ? as i am doing a v2g application thus i am trying to use the DC link as reference, its it a wise choice to use it ?
İyi günler hocam. Videolarınızın çok yardımı dokundu teşekkürler. Güç kaynağı olarak güneş paneli kullanmak istiyoruz. Bu durumu sisteme nasıl entegre edebiliriz.
Kindly continue this precious work. And also perform some simulations on SHEPWM, SVCPWM control techniques for multilevel converters such as cascaded, neutral point converter and flying capacitor converters etc. Its my humble request😐 if you know about these techniques.
Actually, I want to explain the basics of power electronics by using Simulink. But, many subscribers want systems that are related to their studies. It is hard for me. Because explanations of control algorithms take a long time. When I have free time, I am making videos. I have experience with NPC multilevel inverters. Maybe next time, I can make a video by the direction of your request. Thank you.
sir i am doing battery and PV mangement project , can the DC supply change to PV input directly? or need some converter to ensure the charging and discharging is functional
If you only want to charge the battery, you can directly connect the PV system. If you have a load, the design will change. You can use a converter for PV and/or you should control the battery power by depending on MPPT.
In general boost converters are using for PV system. Of course, you need an MPPT algorithm. The load should be connected to DC bus. You should control the dc bus.
The management algorithm may change by depending on your system. You should decide follows: - When the battery will be in charge mode? (I mean, the algorithm should contain SOC limits) - When the battery will be in discharge mode? - What is the emergency back-up limit? - When the battery is fully charged(100%), you should stop the charge.
@@subhabhaskaran1827, Actually the control algorithm works based on current control. But outer loop changes by depending on charge or discharge. As you said, the load is a constant voltage part for discharge mode. While the system is in charge mode, the algorithm works based on critical voltage point. These two-part generate a current reference for the inner loop.
@@nakiguler Sir, i am a final year student. I use the same software as yours but i didnt get the result of regenerative braking and i stuck at motor part. I did not know how to connect it. i would really appreciate if you can consider to guide me a bit regards the issues. Perhaps via email?
Hocam merhabalar, Vehicle-to-Grid konsepti üzerinde çalışıyorum ve sizin videolarınız gerçekten çok işime yaradı öncelikle bunun için teşekkür ederim. Bi-Directional converter ve controller konusunda bir soru işareti yok aklımda ancak size sormak istediğim benim bu sistemi bir inverter kullanarak şebekeye bağlamam gerekiyor. Ve işin içine şebeke kısmı da dahil olunca alternatifler çok fazla Simulink'te. Bu konuda bir tavsiyesiniz olur mu şu bloğu kullanabilirsin veya şu yöntemi takip edebilirsin gibi? Sevgiler, teşekkür ederim.
Hello Sir, I have followed your tutorial and have some questions: If this battery controller model were attached to an electric motor, what would be the load voltage being demanded by the motor in this model? would it be the 6V-resistor called "load" or the DC voltage source block (48)V? I will apreciate your kind feedback.
Hi sir.. Thank you thank you very much for this video.. I have one doubt..My application is charging a battery by another battery bidirectionally.. Is this setup good for it..please help with this case... I will be grateful for your help
Hi Sir, I am a grad student of Electrical Engineering at NIU and I am doing a project on using Neuro Fuzzy logic in controlling a hybrid microgrid, can you please let me know how can I contact you for more help.
Can this take on the role of an MPPT Solar Charge Controller? If not, how can I find an MPPT Solar Charge Controller or the blocks to create it, in the library?
@@nakiguler i tried to check the general circuit of a buck boost converter and ive seen that it does not have a resistor for the inductor and capacitor
Hello Sir, I want to replace the DC voltage source with Grid, I try to use the grid-connected inverter for that, but actually we need Rectifier to change AC grid voltage to DC voltage source. Can you give me some details on how I can connect a grid (3 ph voltage source) to charge battery. I have made an rectifier with output current control can that be able to replace the DC voltage source.
Please check the working principle of the bidirectional converter. Some converters uses Diode, some of uses IGBTs. Because it is bidirectional it needs two IGBTs.
Hello, actually PID and MPC are different controller types. So, one of them uses system parameters (MPC), PID has a tuning procedure depending on converter dynamics. So, the implementation procedure of MPC is different from PID.
Hello, really good video!I want to design the same charger but for 400V battery, so I would like to ask you how do you calculate the values of L,C. Thank you! *I want it for my thesis not for job.
Actually it does not matter. MOSFET or IGBT can be used. Yes, you can add more load to the battery. But, you should check the current limit. You may need to increase battery power limits.
Can you send me this simulation? My project name is to to develop prototype charging facility by bi directional buck boost converter for electric vehicle
@@rushipatel8565 it is very easy to model it in simulink. If you'll try yourself then you'll find out many more things and be able to understand this much better !
ASAP Sir, how to connect the battery to 3 phase (Vrms=380V) microgrid? Please could you answer me? I am struggling by connecting the 3P inverter and do not know the inductor, resistor and capacitor value at the output. In my system, I have PV, varying load and controlled generator. I only need BESS.
I would like to ask you if you do not mind, please. I controlled the voltage at constant level, and when I simulate the system, The voltage is kept constand SOC is at constant level, which is 75% The current is zero That wasin charging mode But, at the discharge mode The voltage is kept constant SOC decrease gradually The current is positive Is that correct
Hi Naki I am unable to connect the s_P and s_N blocks to the mosfet, am i doing something wrong ? they won't attach to the "g" connection Am i not dragging them correctly or do they need configuring?
I have 3 different scenarios for solar power, wind power and load demand. On the basis of these I want to create charge and discharge signal for battery. Like 1000 solar, 1000 wind and load demand which will be negative feedback to the summer then what should be the PI gains to charge and discharge battery??
Naki can i ask you a question? I am a student and i can't get discharge pulses curve at different temperature by lab test. Can i get these curves from manufacturer? What are keywords should i search for because i tried alot but i didn't find any result?
Youness Laazibi, because the voltage source is an infinity bus. If we decrease its voltage, the battery can not enough power to increase its voltage to the desired level. It is only a scenario, you may use a dc bus.
@@nakiguler Hi sir, I would like to ask what is the preferred nominal voltage and capacity of the battery in a grid-connected system in which PV provide power
How do you change to T = 20 sec, mine ended at 10 sec for simulation and do you know how to control buck boost converter using soc of battery instead ?
Hi, i using version 2016. In discrete PID controller parameters, there is no tab for initialization & output saturation. Mine got PID advanced only. pls advice
@@nakiguler, yes have external reset tab. choose from rising, falling, either or level. I have tab such as Main, PID Advanced, Data types & state attributes only.
@@rameshvijayan966 , you may use a saturation block as externally. And also, you may need to reset the PI controller. It may exceed saturation limits.
Başrıl payalaşınız için çok teşküer ederim ,hocam dc dönüştürcünün yükün yerine charger batarye tasarlarsam nasıl bir ortak kontrol gerçekleştermelıyım hem dönüştürücye hemde yüke ?
İlginiz için teşekkürler. Yük yerine bir batarya eklerseniz iki batarya arasında güç dağılımı söz konusu olacaktır. Nasıl bir sisteme ihtiyacınız olduğunu açıklarsanız ona göre öneride bulunabilirim.
@@nakiguler Hocam dc buck konverter systemin girişine 24V , ve 12v çivarında çıkış estiyourum bataryie şarge etmek için , buck systemi kp ile kontrol etim ama batariye balarken ortak kontrol sağlamyı bilmiyourum
Sir please upload a tutorial related to single input multiple output dc source where we can get different small voltage dc sources of our choice from a bigger value of DC source.
Thanks. Because of the battery has bidirectional power flow, the current may be negative and positive. The reference current determines the charge or discharge current.
Thank you soo much sir, this video has been of great help. The video was totally understandable, but could you add an explanatory voice, cause that would speed up the work a little bit. It would be easy for the viewer also to do the modeling. but still, Very well explained. Kudos!!
Thank you so much!!!!!
Please use the sound if you can next time and explain while you doing it. It will help student a lot.
Anyway thank you again!!!!!! :)
Can you please share formulas used to calculate values of Resistors, Capacitor and Inductor in the bi-directional converter .
@syed Daniyal have you find the formulas about bi bidirectional converter? Help me please?
for voltage PI control why did you multiply with -1 gain blocK?
Thank you for sharing your knowledge and time. I made it according to the video and everything works perfectly.
Hello Brother
@@qasimsaleem635 hello brother.
@@gadegroof if you please share me the matlab file that you have implemented recently . My email address is “qasimsaleem1988@yahoo.com”. I’ll highly appreciate your cooperation.
Could you share how did you get the values of the integrator, capacitor, inductor? Why did you change the value of the sample time of the discharging PI?
Hello sir @Naki GÜLER i want to know how to switch from Constant current to constant voltage mode at 80% SOC . It should sense automatically and enter into CV mode from CC mode. I have seen that you had changed the value manually i want to done automatically.
Great in detail video !! Thanks .
Please make BMS system video also
Sir, How do you calculate the inductance of converter and the DC Link in front of the load. and where is there not a need to put a Capacitor after the inductor for limiting the voltage variation. What is the load current for this circuit, Iref or Ibat ? as i am doing a v2g application thus i am trying to use the DC link as reference, its it a wise choice to use it ?
Tq so much sir.
Such a great help!🙂sir.
You're welcome naani :)
Can use show how can we use tuning using Z-N method for any of the PI calculations?
sir can you please tell me which alogrithim you have used for controlling
Bless you for your effort
Is there a paper or research related to it that you can provide me with?
Hello,It seems to be a nice model. Plz explain the procedure for selecting PID parameters
İyi günler hocam. Videolarınızın çok yardımı dokundu teşekkürler. Güç kaynağı olarak güneş paneli kullanmak istiyoruz. Bu durumu sisteme nasıl entegre edebiliriz.
thanks for sharing your knowledge i really appreciate
Kindly continue this precious work.
And also perform some simulations on SHEPWM, SVCPWM control techniques for multilevel converters such as cascaded, neutral point converter and flying capacitor converters etc. Its my humble request😐
if you know about these techniques.
Actually, I want to explain the basics of power electronics by using Simulink. But, many subscribers want systems that are related to their studies. It is hard for me. Because explanations of control algorithms take a long time. When I have free time, I am making videos. I have experience with NPC multilevel inverters. Maybe next time, I can make a video by the direction of your request.
Thank you.
@@nakiguler oh thats great😊
Thanku so much sir
You considered me
Sir still am waiting for ur next video
Rawal Balouch, thanks for interest. But I am so much busy for one month. After that, I will add a new one.
how did he put those values? i think calculations should have been included, else the video won't make much impact for learners.
thanks
Hey can u help me with this video?
Thank you very very very much
Thank you
many thanks
very many thanks💗💗💗💗💗💗💗💗
Sir, this is which type of charging....CC or CV or CC-CV
Sir, when i disconnect the load the battery is not charging.
Can you make video on how you tune PID controller in bidirectional converter using ziglar Nicholas method please.
sir i am doing battery and PV mangement project , can the DC supply change to PV input directly? or need some converter to ensure the charging and discharging is functional
If you only want to charge the battery, you can directly connect the PV system. If you have a load, the design will change. You can use a converter for PV and/or you should control the battery power by depending on MPPT.
Naki GÜLER if i have resistive load, what converter should use? Does mppt also need to be connected?
In general boost converters are using for PV system. Of course, you need an MPPT algorithm. The load should be connected to DC bus. You should control the dc bus.
How do you decide the value of all these parameters. Please give me more details.
many thanks for the video. how could you determine the switching frequency for the PWM generator? is the (10 kHz) obtained with a rule?
could you provide the reference for the design? Any book or research paper?
Can we integrate this model with Dc microgrid bus ??
Of course, it may need a different control strategy.
Can you please explain how did we manage that ?
The management algorithm may change by depending on your system. You should decide follows:
- When the battery will be in charge mode? (I mean, the algorithm should contain SOC limits)
- When the battery will be in discharge mode?
- What is the emergency back-up limit?
- When the battery is fully charged(100%), you should stop the charge.
Could you integrate this model to the DC bus? I also struggling about the same issue. If you have done, can you tell me how did you do that?
Sir, what is your method to tune for Kp and Ki ?
I am finding it's by try. You may use Ziegler Nicholas tuning method.
Sir what is the difference between this video and previous video with bidirectional converter and battery??
The previous one shows the battery connection to the bidirectional converter. This one demonstrates the charge and discharge control of the battery.
Good sir ...the control strategy used is combination of constant current and constant voltage??
@@subhabhaskaran1827, Actually the control algorithm works based on current control. But outer loop changes by depending on charge or discharge. As you said, the load is a constant voltage part for discharge mode. While the system is in charge mode, the algorithm works based on critical voltage point. These two-part generate a current reference for the inner loop.
@@subhabhaskaran1827, hi can i have ur email ?
Sir can i relate this project with regenerative braking system for electric vehicle? I really appreciate your kind respond.
Yes, it is possible. Because power flow is bidirectional. But the motor type may change the design.
@@nakiguler Sir, i am a final year student. I use the same software as yours but i didnt get the result of regenerative braking and i stuck at motor part. I did not know how to connect it.
i would really appreciate if you can consider to guide me a bit regards the issues. Perhaps via email?
Why reference battery current is swinging in both negative and positive values?
Is this bidirectional charging?
Both V2G and G2V
Could this battery control design be implemented directly to MPPT system explained in your previous video?
It may require a management algorithm.
Hocam merhabalar,
Vehicle-to-Grid konsepti üzerinde çalışıyorum ve sizin videolarınız gerçekten çok işime yaradı öncelikle bunun için teşekkür ederim. Bi-Directional converter ve controller konusunda bir soru işareti yok aklımda ancak size sormak istediğim benim bu sistemi bir inverter kullanarak şebekeye bağlamam gerekiyor. Ve işin içine şebeke kısmı da dahil olunca alternatifler çok fazla Simulink'te. Bu konuda bir tavsiyesiniz olur mu şu bloğu kullanabilirsin veya şu yöntemi takip edebilirsin gibi?
Sevgiler, teşekkür ederim.
Hello Sir, I have followed your tutorial and have some questions: If this battery controller model were attached to an electric motor, what would be the load voltage being demanded by the motor in this model? would it be the 6V-resistor called "load" or the DC voltage source block (48)V? I will apreciate your kind feedback.
Hi sir.. Thank you thank you very much for this video.. I have one doubt..My application is charging a battery by another battery bidirectionally.. Is this setup good for it..please help with this case... I will be grateful for your help
Hi Sir, I am a grad student of Electrical Engineering at NIU and I am doing a project on using Neuro Fuzzy logic in controlling a hybrid microgrid, can you please let me know how can I contact you for more help.
Hi , I am working on coordination of battery energy storage systems. Can we work together
@@sravankumar5209 yes
Hi there, I would like to ask, for this model is it the discharging mode based on the Constant Current?
Mr.Naki thank you so much for the video ,
How did you calculate the "PI" parameters (0.005 , 10 and 40 , 2000) ?
Hi, I didn't calculate the parameters. You may check the Ziegler Nichols method.
which DCDC converter using?
cann the same design be used with a pv panel?
Please, does it work for battery 48v to dc link 600v?
Just a great WORK!
Thanks You so much . CAN YOU please add reference book or artical for detail and can we use this model according to our desire spècification ???
You are welcome. I have no paper or book for the model.
It's amazing video
Thank you 😊
sir .is this can direct charge to battery without load connect?
Can this take on the role of an MPPT Solar Charge Controller? If not, how can I find an MPPT Solar Charge Controller or the blocks to create it, in the library?
what is the use of resistor for the inductor and capacitor? how did you compute for the values?
These are the non-ideal type of passive components.
@@nakiguler i tried to check the general circuit of a buck boost converter and ive seen that it does not have a resistor for the inductor and capacitor
@@zxcv7586 these are internal resistors. Not so much important, if you want you may neglect it.
@@nakiguler thank you :)
@@nakiguler another question sir, how did you tune the PI controller?
what if you use a fuzzy logic algorithm? Which parts need to be replaced/changed?
Do you know how the PI parameters are selected?
what about if duty cycle is below 50% and above?
what duty cycle level is discharging?
merhaba Naki hocam,
faydalı paylaşımlarınız için teşekkür ederim. RLC elemanlarının değerini nasıl belirliyorruz. teşekkürler
Merhaba,
İlginiz için ben teşekkür ederim. Buradaki değerleri deneyerek buldum ancak, Texas Instruments'in buck-boost appliacation not'una bakmanızı tavsiye ederim. İyi çalışmalar.
Hello Sir, I want to replace the DC voltage source with Grid, I try to use the grid-connected inverter for that, but actually we need Rectifier to change AC grid voltage to DC voltage source. Can you give me some details on how I can connect a grid (3 ph voltage source) to charge battery. I have made an rectifier with output current control can that be able to replace the DC voltage source.
is this bidirectional buck-boost dc/dc converter?
Yes, Nazrul.
Why is the both of the IGBTs for buck and boost working at the same time when in charging or discharging mode? Thank you.
Please check the working principle of the bidirectional converter. Some converters uses Diode, some of uses IGBTs. Because it is bidirectional it needs two IGBTs.
Please can you tell me how can I control the battery soc (from charging and discharging) just from the source
can you tell me how did you calculate the ref current?
Your video is good but how you find the value of capacitor and inductor???
You may search design of bidirectional dc/dc converter. The video shows power flow....
Hello sir,
Can I get motor controller design for Electrical vehicles?
Dc dc converter is boost but whole model is o/p to i/p u have taken???
Elinize sağlık hocam
Hello sir, in this video it seems that you are using PID controller for the battery. Is it the same way to implement MPC for the battery?
Hello, actually PID and MPC are different controller types. So, one of them uses system parameters (MPC), PID has a tuning procedure depending on converter dynamics. So, the implementation procedure of MPC is different from PID.
Sir, is this circuitry also work di directional converter.
Yes, while the battery discharging, power direction is opposite to charge. So it works as bidirectional.
thanks great video
hi, i tried to replace the DC source with a pv array . what adjustments i should make please!
What is your aim with the PV based system? It changes the control requirements.
Can you please show the algorithm for CV mode of charging for SOC>80
Hello, really good video!I want to design the same charger but for 400V battery, so I would like to ask you how do you calculate the values of L,C.
Thank you!
*I want it for my thesis not for job.
How can i use this battery to feed an inverter to control an bldc Motor?
why mosfet is used ? can we add more load or devices to battery bro
Actually it does not matter. MOSFET or IGBT can be used. Yes, you can add more load to the battery. But, you should check the current limit. You may need to increase battery power limits.
Sir, how to balance multiple cells example three cells if they are connected in series.
Hello SIr, How the graphs of SoC and Voltage are increasing?? Because in my case graphs are decreasing
for me also
Same for me also
how did you decide the integrator value to be 0.54?
Can you send me this simulation? My project name is to to develop prototype charging facility by bi directional buck boost converter for electric vehicle
@@rushipatel8565 it is very easy to model it in simulink. If you'll try yourself then you'll find out many more things and be able to understand this much better !
how to decide values for PI controller?
Thank you so much 🙏
Hi sir,May I see this file as the basis for my research
ASAP
Sir, how to connect the battery to 3 phase (Vrms=380V) microgrid? Please could you answer me? I am struggling by connecting the 3P inverter and do not know the inductor, resistor and capacitor value at the output. In my system, I have PV, varying load and controlled generator. I only need BESS.
I would like to ask you if you do not mind, please.
I controlled the voltage at constant level, and when I simulate the system,
The voltage is kept constand
SOC is at constant level, which is 75%
The current is zero
That wasin charging mode
But, at the discharge mode
The voltage is kept constant
SOC decrease gradually
The current is positive
Is that correct
Hi Naki I am unable to connect the s_P and s_N blocks to the mosfet, am i doing something wrong ? they won't attach to the "g" connection Am i not dragging them correctly or do they need configuring?
Hi, you should use "goto" and "from" blocks. Also, please be sure: you should get the Mosfets from the correct library.
I have 3 different scenarios for solar power, wind power and load demand.
On the basis of these I want to create charge and discharge signal for battery.
Like 1000 solar, 1000 wind and load demand which will be negative feedback to the summer then what should be the PI gains to charge and discharge battery??
hi have you found your answer anywhere?
what is the role of two MOSFETs in the circuit?
A basic Bidirectional DC - DC Converter consists of two switches, think of it as a buck & boost converter separately
Can we use this system for a wind turbine like a stock system ?? But i need a ac voltage how i can do this
how did you choose the PI parameters?
Do you now know how PI parameters are selected?
@@HimanshuGupta-xm2sj cant remember watching this video lol, use try and error to find out the best parameters for the PI
@@hassaniskandarani1345 I had to do the same 😂
Naki can i ask you a question?
I am a student and i can't get discharge pulses curve at different temperature by lab test. Can i get these curves from manufacturer? What are keywords should i search for because i tried alot but i didn't find any result?
Actually, if you get your battery from a big company, you may find these informations. If no, it may not be possible.
thank u for helping us
can u implement for us an hybrid system using wind turbine and PV and battery
You're welcome. I may add a hybrid system in future. I am so much busy, when I have a free time, I am planning to add a video about wind turbines.
@@nakiguler thank u; just one question. why we have to use a breaker? why we can't conect directly source with a load?
Youness Laazibi, because the voltage source is an infinity bus. If we decrease its voltage, the battery can not enough power to increase its voltage to the desired level. It is only a scenario, you may use a dc bus.
@@nakiguler please sir make it
what the purpose of the battery controller
Hello sir, which MATLAB version u used while doing a simulation.
I am getting some error.
Hello, I am using 2019a. What is the problem please type here.
@@nakiguler ok sir .i solved the error . thank u for your reply.
@@nakiguler Hi sir, I would like to ask what is the preferred nominal voltage and capacity of the battery in a grid-connected system in which PV provide power
How can i make a battery pack and then do the same control
How do you change to T = 20 sec, mine ended at 10 sec for simulation and do you know how to control buck boost converter using soc of battery instead ?
28:53 you can see a box where at middle-top. the box show 20. change it to 20 seconds.
Dear Sir . How can I get a continuous voltage of 48 volts from this circuit
Hello sir, i need your help! Can you explane me, how did you calculate the PI Controller? This help me for my Masterthesis.
Sir I am doing for 16v as dc source and 5v battery what kp,ki values should i mention in control controller and voltage controller
You should try some values. Firstly you may start with small Kp and then increase Ki.
Sir, how can we build a algorithm that for 80% SOC its Constant Current Mode and after 80% SOC it switches to Constant voltage mode.
You may do that with Matlab function(code part). You can select the charge method by comparing the SOC with critical points.
@@nakiguler Can you make a video for this constant current constant voltage mode algorithm??
@aman were you able to implement it?
@@ryansujith1504 no I'm not able to.. did you implemented it ?!!
Hi, i using version 2016. In discrete PID controller parameters, there is no tab for initialization & output saturation. Mine got PID advanced only. pls advice
Hi, is it has a reset port? Could you please write the block specifications? By the direction of these, I may suggest something.
@@nakiguler, yes have external reset tab. choose from rising, falling, either or level. I have tab such as Main, PID Advanced, Data types & state attributes only.
@@rameshvijayan966 , you may use a saturation block as externally. And also, you may need to reset the PI controller. It may exceed saturation limits.
@@nakiguler, can you show me how to do it ?
@@rameshvijayan966 have you done this work
Başrıl payalaşınız için çok teşküer ederim ,hocam dc dönüştürcünün yükün yerine charger batarye tasarlarsam nasıl bir ortak kontrol gerçekleştermelıyım hem dönüştürücye hemde yüke ?
İlginiz için teşekkürler. Yük yerine bir batarya eklerseniz iki batarya arasında güç dağılımı söz konusu olacaktır. Nasıl bir sisteme ihtiyacınız olduğunu açıklarsanız ona göre öneride bulunabilirim.
@@nakiguler Hocam dc buck konverter systemin girişine 24V , ve 12v çivarında çıkış estiyourum bataryie şarge etmek için ,
buck systemi kp ile kontrol etim ama batariye balarken ortak kontrol sağlamyı bilmiyourum
Sir please upload a tutorial related to single input multiple output dc source where we can get different small voltage dc sources of our choice from a bigger value of DC source.
Hi. I am getting an error because the Sample Time of powergui and PI Controllers are different. Please help.
Merhabalar, yaptığınız projeyi paylaşma şansınız var mı?
Sir, In charging mode also my battery is getting discharged. I don't understand what is wrong. Please Suggest.
Please check the plus and minus that used to obtain errors. It may change the PI controller behavior.
merci beaucoup mon frère
Hey man, great video! From where -5 comes from? And what means reference current? Can you please elaborate or give information to google it.
Thanks. Because of the battery has bidirectional power flow, the current may be negative and positive. The reference current determines the charge or discharge current.
hocam buradaki elemanların değerlerini nasıl hesaplayacağız?
Ben burada tasarım hesabı yapmadım ama design of bidirectional converter olarak bakarsan faydalı olabilir. Kolay gelsin
@@nakiguler cevap için teşekkürler hocam dediğiniz gibi aratıp inceleyim
Thank you soo much sir, this video has been of great help. The video was totally understandable, but could you add an explanatory voice, cause that would speed up the work a little bit. It would be easy for the viewer also to do the modeling. but still, Very well explained. Kudos!!
Thanks for your suggestion. I am trying to explain new videos with voice.
What are the mathematical equations of the circuit?
I selected these parameters, but you may check design of the bidirectional converter.
Sir can you make a video this battery charging model integrated with PV mppt control (previous video). Thanks a lot